ADT Security Services NV412AADT Video Encoder Installation Guide

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ADT Pulse®  Interactive Solutions  
NV412 A-ADT 
Video Encoder  
Installation Guide  
 
    
						

							NV412A-ADT Video Encoder Installation Guide 
 
Table of Contents 
INTRODUCTION  ...........................................................................................................  1 
Overview .......................................................................................................................  1 
NV412A-ADT Features .......................................................................................  1 
Package Contents .......................................................................................................  1 
Physical Details – NV412A -ADT ..............................................................................  2 
Front Panel ............................................................................................................  2 
Rear Panel ..............................................................................................................  3 
INSTALLATION .............................................................................................................  4 
Configuring the NV412A-ADT  .................................................................................  4 
Adding the NV412A-ADT to your ADT Pulse Wireless Network  ......................  4 
Wall Mounting (Optional)  ..........................................................................................  8 
APPENDIX A: SPECIFICATIONS  ...............................................................................  9 
APPENDIX B: REGULATORY APPROVALS ..........................................................  10 
FCC Statement ..........................................................................................................  10 
CE Approvals .............................................................................................................  10 
 
 
 
 
 
 
 
 
 
 
UNITED STATES LICENSE INFORMATION: AL  Alabama Electronic Security Board of Licensure, 
7956 Vaughn Rd., Montgomery 36116, (334) 264 -9388;  AK 37950, 5520 Lake Otis Pkwy., 
Anchorage, AK 99507;  AR E12 -041, Regulated by Arkansas Bd. of Private Investigators & Private 
Security Agencies, #1 State Police Plaza Dr., Little Rock, AR 72209, (501) 618 -8600;  AZ ROC 
279591;  CA ACO7155, alarm company operat ors are licensed and regulated by the Bureau of 
Security & Investigative Services, Dept. of Consumer Affairs, Sacramento, CA 95814, 974443, 
PPO17232;  CT ELC.0106069 -L5;  DC ECS902743;  FL EF0001121;  GA LVA205265,  -205326,  -
205572,  -205679,  -205878, LVU405673 , -004349;  HI  CT -32297;  ID  ELE- SC-2643; 
IL  124001792;  LA F1639, F1640, F1643, F1654, F1655;  MA 172C;  MI 3601206258, 
5103208    -  4182 Pier North Dr. Ste. D, Flint,  MI 48504; MN TS650251;  NC 7535P2, 7561P2, 
7562P10, 7563P7, 7565P1, 7566P9  -  Alarm Systems Lice nsing Bd., 4901 Glenwood Ave, Ste. 
200, Raleigh, 27612 (919) 788- 5320; NM 374838; NV 0077105;  NJ Electrical Contractor Lic. #'s 
34FA00140500, 34BA00179000, 7895 Browning Rd., Pennsauken, NJ 08109; 
NY    12000305615, Licensed by NYS Dept. of State; OH  50- 18- 0018, 50 -25 -0023, 50- 29-0003, 
50- 31- 0014, 50 -48 -0008, 50 -50- 0005, 50- 76-0006, 50 -89 -0016, 53 -89 -1726;  OK 1995; 
OR    196560;  PA Pennsylvania Home Improvement Contractor Registration Number: PA090797; 
RI   35683;  TN ACC- 1688,  -1689,  -1690,  -1691,  -1692,  -1693,  -1694,  -1695,  -1696; TX B17944 -
140 Heimer Rd. Ste. 100, San Antonio, TX  78232    -  Texas Private Security Bureau, 5805 N. Lamar 
Blvd., Austin 78752; UT  8289653;  VA 11 -7345, 11 -7348, 11 -7351, 11 -7354, 11- 7598, 11-7900, 
11- 8205, 11- 8353, 11-8447 2705147728 Cl ass B Contractor Classification ESC; 
WA   ADTLLL881DO, 11824 N Creek Pkwy #105, Bothell, WA 98011;  WI 1210943;  WV 049758.  
MS 15019511  ©2013 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo, 800 ADT.ASAP 
and the product/service names  listed in this document are marks and/or registered marks. 
Unauthorized use is strictly prohibited.  
 
Canada  Licence number:  RBQ 3019 -4070 -50.©2013 ADT Security Services Canada, Inc. All rights 
reserved. ADT, the ADT logo, 800.ADT.ASAP and the product/serv ice names listed in this document 
are marks and/or registered marks. Unauthorized use is strictly prohibited.  
 
 
Document  957YDC02MY  
Ver sion 1.1  
ii  ADT Pulse® Interactive Solutions 
  
						

							NV412A-ADT Video Encoder Installation Guide 
 
Introduction 
This installation guide provides simple, step-by -step instructions for configuring 
and installing your  NV412A-ADT  Video Encoder on  your ADT Puls e® w ireless 
system . 
 
Overview   
The NV412A-ADT  (hereafter referred to as the  video encoder) digitizes video 
signals and streams digital images directly to the  ADT Pulse wireless system .  
 
NV412A -ADT Features   
•  Easily installs t o the ADT Pulse wireless system  
•   MPEG4 and JPEG encoders built into the video encoder generate a ready -to 
view video stream  
•   Supports TCP/IP networking  
 
 
Package Contents   
1. NV412A- ADT Video Encoder  
2. 12V Power Adapter  
3. Video Output Terminator  
4. Two  Mounting Brackets   
5. Four  Mounting Screws   
6. Installation Guide 
  
ADT  Pulse® Interactive Solutions 1 
  
						

							NV412A-ADT Video Encoder Installation Guide 
  
Physical Details – NV412A -ADT   
  
Front Panel     
 
Figure 1: Front Panel 
Video Out To ensure the best quality video, attach a coaxial 
terminator to the Video Out  connector . 
Video In  Supports a single composite video source. 
Line Out / 
Line/Mic In  
Not Used 
IMPORTANT 
 THE LINE OUT AND LINE/MIC IN INPUTS ARE NOT 
SUPPORTED BY ADT PULSE.
 
Network LED 
(green)   On
 –  Ethernet connection is detected 
Off  –  Ethernet connection is  not detected  
Blinking  –  Data  is being transmitted or received via the 
Ethernet  connection 
Active LED 
(green) 
Off – No user is viewing the video encoder 
Blinking  –  User is viewing the video encoder  
Power LED 
(green) 
On – Power on 
Off –  No power  
Blinking  –  Ready mode  
Reset The device can be reset when the video encoder is in the 
ready mode. Using a pin or paper clip, press and hold the 
reset button for at least 10 seconds. The communication 
configuration settings of the video encoder  reset to the 
manufacturer ’s default settings.  
IMPORTANT 
 The Reset button changes 
the communication 
configuration settings and should only be used under 
the direction of ADT support.  
 
   
2  ADT Pulse® Interactive Solutions 
  
						

							NV412A-ADT Video Encoder Installation Guide 
  
Rear Panel    
 
Figure 2: Rear Panel 
 
Ethernet Port Uses a standard Ethernet cable to connect the video 
encoder  to the  ADT Pulse  Gateway.   
Power Port  The supplied 12VDC power adapter connects to the video 
encoder’s power supply .  
Terminal 
Blocks  
Not Used. 
IMPORTANT THE TERMINAL BLOCKS ARE NOT USED WITH ADT 
PULSE.  
 
 
ADT Pulse® Interactive Solutions 3 
  
						

							NV412A-ADT Video Encoder Installation Guide 
 
Installation 
This section  provides details of installing and configuring the  NV412A -ADT 
Video Encoder . 
 
Configuring the NV412A -ADT    
The following instructions provide details of configuring the video encoder . 
1.  Connect the Video Output  of the analog camera to the Video In  on the 
video encoder , using a standard video cable with a BNC connector.  
2. Connect the Video Output Terminator to the Video Out  on the video 
encoder , to ensure the best video quality.  
  
Adding the NV412A-ADT to your ADT Pulse  Wireless 
Network   
 
IMPORTANT 
 
Only use one Video Encoder per analog camera.   
No more than 10 cameras (analog or wireless) can be 
enrolled  on  the ADT Pulse Gateway.  
 
1. Open your web browser. In the address bar, type:  
https://Portal.ADTPulse.com. 
2.  Type your Username  and  Password, and  then cli ck the Sign In  button.  
 
4  ADT Pulse® Interactive Solutions 
  
						

							NV412A-ADT Video Encoder Installation Guide 
 
3. Click the System  tab , and  then click the Manage Devices  button. 
 
4. In the Manage Devices Assistant , click Cameras. 
 
 
ADT  Pulse® Interactive Solutions 5 
  
						

							NV412A-ADT Video Encoder Installation Guide 
 
5. Click the picture of the NV412A  or select it from the drop- down list, and 
then click the Continue  button.   
 
 
6.  Assign the video encoder  a unique camera  name in the space provided, and  
then type the video encoder’s  MAC ID  in the space provided.  
 
 
NOTE:  A valid MAC ID is 12 characters long and contains only 
numbers and/or the letters A
-F.
 
 
7.  Click the Continue  button.  
 
6  ADT Pulse® Interactive Solutions 
  
						

							NV412A-ADT Video Encoder Installation Guide 
 
8. Connect the video encoder  to the Device LAN  port of the  Gateway  using the 
Ethernet cable.  
9. Connect the power supplies for both the analog camera and the video 
encoder . 
10.  C lick the Continue  button.  
 
 
NOTE:  The 
Power  LED turn s on  briefly , and then starts  blinking for 
approximately 15 -20seconds during startup . After startup 
is complete, the Power and Network LEDs on the f ront of 
the  vide o encoder  turn solid green.
 
 
11.  Once connected, click the Continue  button. 
 
ADT Pulse® Interactive Solutions 7 
  
						

							NV412A-ADT Video Encoder Installation Guide 
 
12. Click  Finish  after the installation is complete.  
 
  
Wall Mounting (Optional)   
If desired, you can mount the NV412A -ADT  to a wall or other solid surface using 
the enclosed mounting brackets.  
 
1.  Attach the mounting brackets to either side of the NV412A -ADT. 
2.  Use two screws per bracket to mount the video encoder  to the surface.  
 
 
8  ADT Pulse® Interactive Solutions