ADT Security Services GD00Z2Garage Door Opener Controller Installation Guide

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-2 - LINEAR P/N: 235971 X22- INK: BLACK - MATERIAL: 20 LB. MEAD BOND WITH 80 LB. WHITE COATED COVER - SIZE: 5.500” X 8.500” - SCALE: 1-1 - FOLDING: ALBUM FOLD - BINDING: SADDLE-STITCH
GARAGE DOOR OPENER
REMOTE COMMAND
CONTROLLER
with TILT SENSOR
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
Installation Instructions
GD00Z-2
® 

Regulatory Information  ●Z-Wave®
 is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
  ●Changes or modi cations not expressly approved by the manufacturer could void the user’s 
authority to operate the equipment.
  ●Les changements ou modi cations non approuvés expressément par la partie responsable de 
la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
  ●This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is...

1
Table of Contents
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
The Garage Controller System  . . . . . . . . . . ....

2
Figure 1. System Overview
THE TILT SENSOR SENDS DOOR
OPEN OR CLOSED STATUS TO THE
GARAGE DOOR CONTROLLER
THE GARAGE DOOR CONTROLLER
SENDS THE DOOR STATUS TO THE
ADT PULSE SYSTEM
THE ADT PULSE SYSTEM
DISPLAYS THE DOOR STATUS
THE ADT PULSE SYSTEM
COMMANDS THE GARAGE DOOR
CONTROLLER TO OPEN
OR CLOSE THE DOOR
Overview
  ◆Replication is the process of copying or transferring your Z-Wave network from one 
controller to another.
  ◆This is a Security enabled Z-Wave product and must be used with a Security...

3
GD00Z-2
GARAGE DOOR
CONTROLLER
POWER
INPUT
JACK
WARNING
LIGHT
INCLUDE
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-2
POWER
SUPPLY TILT
SENSORSTATUS
INDICATOR
OPTIONAL
ADJUSTABLE
GD00Z-2 MOUNTING
BRACKET
POWER
SUPPLY
RETAINING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSORSCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
The Garage Controller System
The GD00Z-2 System consists of three major components:
The Controller — The Controller wires to the...

4
Mounting the Tilt Sensor
The battery powered Tilt Sensor attaches to the top panel of the garage door.
1. Before installation, activate the Tilt Sensor by pulling and removing the battery 
protection strip.
2. If using screws to mount the Tilt Sensor, open the sensor case with a small 
screwdriver.
3. Use the double-sided tape or screws supplied to attach the Tilt Sensor to the top panel 
of the garage door.
  ✓NOTE: Drill two 1/16” pilot holes if using the screws to attach the mounting plate.
4. If...

5
Enrolling the Garage Door Controller
Before the system can be used, the ADT Pulse system needs to enroll the Garage Door 
Controller. Bring the Controller near your ADT Pulse Gateway and apply power to the 
Garage Door Controller.
  ✓NOTE: Before enrolling device to any Z-Wave network, or after removing it from any Z-Wave 
network, it is recommended that the Controller be factory reset. Reset the Controller by 
pressing the Include button 5 times.(Location of Include button is shown in Figure 2 on...

6
4. In the Manage Devices Assistant window, click Lights, Thermostats & More.
5. From the drop-down list, select the Garage Door Remote Controller, and then click 
Continue.
6. At the Trigger Device screen, press and hold the Garage Door Controller’s include 
button for 1 second (See page 3, Figure 2 for the location of the include button).
7. Wait while the system  nds the GD00Z-2 Device. When the device is successfully 
recognized, the Found Device screen appears.
  ✓NOTE: Adding the Garage Door...

7
8. Enter a name for the device, and then click Continue.
A message informs you that the device was successfully added.
9. Click Finish.
Enrolling with the System (Cont.) 

8
Resetting or Excluding the Garage Door Controller
If you have trouble adding the Garage Door Controller you can reset the device. Resetting 
the device removes it from a site (Not the same as factory resetting the device). You can 
then try to add the device again.
To reset a Garage Door Controller:
1. In the web portal, click the System tab.
2. Click Manage Devices.
  ◆The Manage Devices Assistant wizard appears.
3. Click Lights, Thermostats & more.
  ◆The Z-Wave Assistant wizard appears.
4. Click...