Addonics Technologies USB HDD Flash duplicator UDFH15 User Manual

Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
www.addonics.com
User Guide
1:15 USB HDD / Flash Duplicator
(UDFH15)
T E C H N O L O G I E S         

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Unpacking and Overview
Power Cord (US Version Shown) 

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Compatibility
Duplicator is USB 2.0 compliant. Works with USB 3.0 devices at 480Mb/s.
Works with the following devices:
- USB Flash media drive
- USB External hard disk
- Addonics Pocket Ultra DigiDrive (including PCMCIA storage devices or 
flash 
  storage with the Addonics adapters)
- Addonics Pocket eSATA/USB DigiDrive
- Addonics Pocket Micro SATA UDD
- Addonics Diamond or Ruby...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
 
For Direct mode:
 Once the Duplicator has analyzed the source device, it will scan for 
suitable target devices. While examining connected targets, the ports g\
reen 
LED will blink. If the device is suitable, the green LED will glow. If the device 
is unsuitable, the red LED will glow. The Display will show how many targets 
are ready.
  Press OK once all of the targets are ready...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
3. Copy+Compare
Performs both the Copy and Compare functions in a single step. Between 
the two functions the devices are all powered down for a duration set by\
 the 
Power Off Time Between Copy+Compare function in the Setup menu. 
Copy+Compare does not display the Copy Area setting.
4. Capacity Check
Performs a basic test on target devices to determine if they are functio\
ning...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
6.2. Measure Speed
Estimates the read and write speed of the target media. After selecting this 
function, the port number in use will appear on the LCD, beginning with \
Port 
2 (the first target). Press the arrow buttons to switch between target\
s. Once a 
target is detected, the test will continue to run without accepting any \
more 
input until it is complete, then provide a...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
6.8. Calc. Checksum
Calculates a checksum value for the  Copy Area function defined in the 
Setup Menu.
NOTE: This function is not to be used to validate copies. Media that have 
identical content and structure may still have different checksums. Testing 
media devices for accurate duplication should only be done using the 
Compare function.
Setup Menu
7.1. Startup Menu
Defines the...

www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US
7.6. Asynchronous
Enables or disables Asynchronous Mode during the copy function. When 
enabled, the Copy, Compare, and Copy+Compare functions will work as 
described by the Quick Start section of this User Guide. When disabled, \
the Copy, Compare, and Copy+Compare functions will work as described 
in the Quick Start section of this User Guide in Direct Mode only.
Default is “Enable.”...