Addonics Technologies Saturn Cipher 35 IDE saturn cipher ed User Manual

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
10
Chapter 6 Attaching USIB int erface cable  
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
Be sure the Saturn cipher key is inserted into the dr ive enclosure prior to 
turning on th e power or attachi ng the USIB  interface cable to the co mputer. 
Hard drive will not be detected if the interface cable is attached to the 
computer without the Cipher key inserted first.  Under such condition, the 
power to the drive enclosure will have to be turned off  and turned back on 
with the Ciph er key already  inserted into the drive enclosure in order for the 
hard dri ve to be detec ted by the system. 
 
The Saturn Cipher drive enclosure can be use d as an internal removab le hard 
drive or as a drive cartridge by  installing the optional drive cradle into the 
drive bay o f a Desktop, Server or any computing equipment.  For m ore detail 
of these options, visit the Saturn Cipher page on Addonics we b site 
www.addonics.com. 
  
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
11
Chapter 7    USIB interface cable installation 
 
USB 2.0 USIB  interface cable  
  
Ø Since USB 2.0 Hi-Speed is an evolution of the existing  USB 1.1 
specification, it is fully forward and backward compatible with 
current USB sys tems.  
 
Ø If you do not have an USB2.0 port, you may install an  optional 
USB2.0 adapter or controller  
             
USB driver installation 
For Win98 and Win98SE  
 
1. Make sure your computer is up and running. 
2. Insert the USB cable to the USB  Port. 
3. A New Hardware Found message shall pops up.  
4. Follow w izard and poin t to the location of the driver. (Follow the 
steps from the Dri ver Disc to where yo u saved the driver files) 
5. Let Windows finish the installation and that’s it. 
6. Double click My  Computer icon and t here should be an extr a drive 
letter for the Saturn Cipher ExDrive. 
7. You may now access the drive. 
 
    Note: Saturn Cipher ExDrive is Plug and play under Windows  XP, and 
Me, 2000. There is no third party driver needed. 
 
              Brand New Har d drive must be Partitioned and Fo rmatted first.
            
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
12
Serial ATA USIB interface cable  
 
 
     
 
 
Serial ATA Saturn Cipher ExDrive Installation 
 For Win98SE, Me, 2000 and XP 
 
 
Note: There no drivers needed to use the Serial ATA cable as long as the 
drivers are installed for the Serial ATA Controller card/chip. It is plug and 
play. 
 
1. Make sure the Seria l ATA cable is securely attach to the back of  the 
drive. (For Addonics Pocket drives such as Pocket CDROM, Exdrive etc. 
you may attach th e USB c onnector t o the USB port of the computer to 
provide power for the pocket dr ives). May vary from system’s US B port 
power output. 
2. Make sure that power is attach to the drive and turned on.   
3. Power on the system or yo u may hot plug  while system is on.  
4. On the Window Desktop, doub le click on the MY COMPUTER icon.                    
5. Plug the Serial ATA connector in to your computer’s Serial ATA port.  
6. Wait for a few seconds, yo ur computer may blink for a moment as well. 
Double Click on the “My Computer” icon if not open yet.  
You are now ready  to use the Saturn Ciph er ExDrive.    
 
 
Note: Brand New Hard drive must be Partitioned and Form atted first.
  
  
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
13
Firewire USIB interface cable  
  
    
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
14
CardBus / PCMCIA setting 
 
The Addonics CardBus PCMCIA card has an option switch can all ow 
you to choose using either PCMCIA m ode or CardBus mode. The switch 
position is as follows: 
       
        
  
 
 
 
 
 
 
 
 
Side View 
 
 
 
 
 
CardBus mode supports WIN 95/98/ME/2000 and XP only.  
For DOS, WIN 3.1x and WIN NT, the switch must be set in 
PCMCIA mode. 
       
Note: Brand New Har d drive must be Partitioned and Fo rmatted first for 
the OS to assign the drive letter.  
 
CardBus/PCMCIA driver installation 
 For Windows 95, 98, 98SE and Me 
 (Do not run the SETUP program from the driver disk, SETUP   
  is for DOS or WIN 3.1 using PCMCIA mode only) 
    
1. Power on your system and wait for the Desktop screen. 
2. Connect the CardBus/PCMCIA cable and external AC/DC adapter 
into the back of y our Saturn Cipher ExDr ive kit. 
3. Plug the CardBus / PCMCIA card end of the cable into the PCMCIA 
slot on the side of y our computer. 
4. The system will automatically identify the new c ard and ask to load the 
driver.  
Front view 
Cardbus and PCMCIA 
selection switch.  
CardB us mode – move the 
switch to the side with the 
DOT indicator 
PCMCIA CardBus 
Factory def ault setting 
is CardBus mode  
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
15
5. Insert the driver diskette in “A” drive and follo w the instruction on the 
screen to load “Addonics CardBus IDE Controller”. Follow wizard 
and point  to the location of the driver. (Follow the steps f rom the 
Driver Disc to where you saved the driver files) 
6. When installation is finished, a PCMCIA card ico n will appear in the 
lower right-hand of the Window’s sy stem tray. 
7. Double Click on the “My Computer” icon. You ar e now ready to use 
the Saturn Cipher ExDrive kit. 
 
Note: Brand New Hard drive must be Partitioned and Fo rmatted first.
  
 
PCMCIA Installation for Windows NT 
 
1.    Go to Start\Settings\Control Panel 
2. Double Click SCSI adapter icon 
3.    Click on the Driver Tab 
4.    Click Add to add new driver 
5.    Follow wizard and poin t to the location of the driver. (Follow the 
steps from the Driver Di sc to where you saved the driver files) 
6. Select “Addonics PCMCIA…” then click ok. 
7.    Windows will prompt yo u for driver location again, to continue 
Type in A:\NT then click continues. 
8.   Click YES to restart your computer. 
9.   Double Click on the “My Computer” icon. You are n ow ready to use 
the Saturn Cipher ExDrive kit. 
 
Note: You must use the PCMCIA mode for Windows NT. 
CardBus/PCMCIA Installation for Windows 2000 
 
1. Make sure your computer is up and runn ing 
2. Verify that all cables are connected and ther e is power to the dr ive. 
3. Insert the PCMCIA cable to the PCMCIA socket. 
4. A New H ardware Found message shall pops up.   
5. Select Nex t to continue installa tion.  
6. Select Search for a suitable driver.... button an d select Next. 
7. In select a Device Driver page, select Have Disk to specify 
location. Follow wizard and point  to the location of the driver. 
(Follow the steps from the Driver Disc to where you saved the driver 
files) Select Addonics CardBus.... click YES for the Win dows 
warning message and let Win2000 to finish the Installation and 
thats it. 
8.   Double Click on the “My Computer” icon. You ar e now ready to use 
the Saturn Cipher ExDrive.  
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
16
 
 
CardBus/PCMCIA Driver installation 
(Windows XP PCMCIA Installation Guide) 
1. Make sure that all  cables are properly c onnected and the drive has 
power. 
2. If you are using the Saturn Ci pher ExDrives, make sure that th e 
power brick has a steady green light. 
3. Boot y our computer  to Windows.  
4. Plug in the Cardbus/PCMCIA cable to  the Computers PCMCIA 
Socket/Port then insert th e card to the Computer. 
5. Windows should now  find a new har dware and ask for the driver 
location. 
6. Follow the Wizard.  Click next to Continue.  
7. Follow wizard and poin t to the location of the driver. (Follow the 
steps from the Dri ver Disc to where yo u saved the driver files) 
example browses to your floppy  drive and go to the A:\Win2kXp 
folder. 
8. Click the second radio button or select the ADVANCED button then 
Click Next.   
9. Select the Search for be st driver in this location”. Ch eck the 
“include this Location in the search” option only then click Browse. 
10. Browse to your floppy drive an d go to the A:\Win2kXp folder. 
11. Select the WinXP driver then click OK, Click next to continue. 
12. Click the Contin ue Anyway  to proceed. 
13. Let the OS install the Driver and thats it. Click Finish. 
             
         Click YES to restart the Computer if prompted and thats it. 
 
 
  
 
 
 
 
 
 
 
  
 
 
 
 
  
						

							Addonics Technologies Saturn Cipher ExDrive Use r Guide 
 
17
Technical Support 
 
If you need assistan ce to get your unit functionin g properly, please call 
Addonics Technical Support .  Our technical staff will be happy to  assist you, 
but they will need your help to do so.  Calling th e technical support staff 
without all the proper information can be both time consuming and 
frustrating.  Here are some tips to help yo u out: 
 
(1) MODEL NUMBER – Please have this number on hand. 
(2) SYSTEM INFORMATION – Type of computer, periph erals, etc. 
(3)   OPERATING SYSTEM – What version of Windows   
(4)   WHAT’S THE TROUBLE? – Give enough information  
About your problem so that we can recreate an d diagnose it. 
 
FREE Software Drivers for all Addonics Technologies 
Products are available 24 hours per day at the  
World Wide Web Site: www.addonics.com. 
 
Contact Information 
 
Addonics Technologies 
2466 Kruse Drive 
San Jose CA, 95131 
 
Phone:  408-433-3899 
Fax:  408-433-3898 
Email:  [email protected] 
Internet:  http://www.addonics.com 
 
TECHNICAL SUPPORT 
Phone:  408-433-3855 
Hours:  8:30-6:00 PST 
Email:  [email protected] 
 
Please visit our web site www.addonics.com to register your warranty online.