Home > Addonics Technologies > Raid Tower > Addonics Technologies RAID Tower IV RTIV535HEU3 user guide web

Addonics Technologies RAID Tower IV RTIV535HEU3 user guide web

    Download as PDF Print this page Share this page

    Have a look at the manual Addonics Technologies RAID Tower IV RTIV535HEU3 user guide web online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 299 Addonics Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Technical Support
    If you need any assistance to get your unit functioning properly, please have your 
    product information ready and contact Addonics Technical Support at:
    Hours: 8:30 am - 6:00 pm PST
    Phone: 408-453-6212
    Email: http://www.addonics.com/support/query/
    v8.1.11
    T E C H N O L O G I E S
    www.addonics.com
    User Guide
    RAID Tower IV
    (RTIV535HEU3)         
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    In sta llin g d riv es in to  t h e 
    R AID  T o w er I V
     
    For the Disk Array 3SA: 
    1. Secure the drive into the tray using the flat
    screws as shown.
     
    2. Slide the tray into the bay with the lever open
    as shown. When the tray slides all the way into the
    bay,  close the lever gently until it snaps into
    position. It is recommended to lock the lever in the
    closed position by turning the safety lock to the
    locked position. 
     
     
    1: Temperature LED and Alarm Reset. When the
    temperature inside the Disk Array exceeds 60°C,
    An alarm will sound and this LED will glow red.
    Pressing the RESET button will silence the alarm
    and turn off the LED.
    2-5: Power Switch and LED for each individual
    drive.
    6: Drive lever safety lock. 
    Disk Array Features:
    For each Snap-In Mobile Rack: 
    1.  Be sure the lock on each drive door is in an unlock position. If not, use the key that came 
    with the Raid Tower to unlock the drive doo r. Pull 
    on the door lever to swing open the drive door all 
    the way .
    2.  Slide a 3.5” SA TA  hard drive into the drive slot 
    with the drive connector side facing in and the label
    side up.  The drive should slide all the way into
    the slot with very  little resistance. Forcing the
    drive into the slot will cause permanent damage
    to the drive or the Snap-In enclosure .
    3.  Once the drive is all the way into the drive slot, 
    close the door all the way till the drive door latch es
    securel y. L ock the  drive door with the ke y. This will
    engage power and data connection with  the hard
    drive.
    4.   To remove the hard drive from the  enclosur e, 
    simply follow the step 2 – 3 in reverse. 
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    Dip Switch S ettings
    Enable
    ERR Buzzer
    Function Auto-
    Rebuilding
    to Spare
    Drive Port Multiplier Mode
    Raid Mode
    1               2    3                4               5
    Individual Drive(Factory Default)OFF
    OFF
    OFF
    OFF
    OFF
    OFF
    OFF OFF
    ON
    ON
    ON
    OFF
    OFF ON
    OFF
    OFF
    OFF
    OFF
    OFF
    OFF
    OFF OFF
    ON
    ON
    OFF ON
    ON
    OFF OFF
    ON
    OFF
    OFF
    OFF ON
    ON
    0
    1 and 10
    3
    5
    Clone
    Large
    R
    AID  Setting B utto n
    Dip S witch
    e S ATA  Host Port  (P ort  5)U SB  3.0 /2 .0  Host Port S
    ATA  Port s
    Error
    and
    Drive
    A ctivit y
    L E D s
    F loppy
    P ower
    Connect or
    B uzze r
    A larm     
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    Default  fact ory  D IP  Swi tc h  sett ing:
    SW 1 –  R AID  S ett ing  DIP  Swi tc h
    BZS  –   Error  b uzze r fu nctio n
    EZ    –   Automa tic  rebuilding  to  s pare  dri ve  (one  o f th e dri ve s o n th e raid  is  se t a s a   
      spare) . If EZ  is  EN ABLE D  anda  drive  failure  occurs , th e spare  will     
      automa ticall y a ct a s a  drive  replacemen t and  rebuilding  will  a utoma tically   
      sta rt.
    M 2  –    RAID  mode  2
    M 1  –    RAID  mode  1
    M 0  –    RAID  mode  0
    1 .  Error  b uzze r fu nction  is  E N ABLE D  ( BZS ) when  dip  s w it c h  is  in  OFF  posit io n
    2 .  Auto-rebuilding  to  s pare  dri ve  is  D ISAB LE D  ( E Z)
    3 .  Indi vidual  dri ve  mode
      is  E N ABLE D  (M0 ~M 2)
    N ote:  W hen  t h e d efaul t f a ctory  R AID  s e tting  is  used , independen t dri ve  c o nfigura tion  
    and  o ptical  drive  are  s uppor te d only  when  c onne cting  to  con trollers  w it h  S ilicon  
    I mage  Sil3124 ,  Sil3132  chip  se t  or  co ntroller s  th at  are  Port  Mul tiplier  (P M ) 
    compa tible . S imul taneous  D VD  wri ting  was  te ste d using  th e Nero  B urning  Rom .
    LE D  Pin  Header
    J1 –  D riv e Act iv it y  L ED
    P 5  –    Activ ity  LE D  fo r e S ATA  h ost por t ligh ts up when  it  is  conne cte d to  a             
      SATA  con troller  card .
    P 0,  P 1,  P 2,  P 3 &  P 4 -  Act iv it y  L E D s fo r por t 
    0 ,  1 ,  2 ,  3 ,  4  &  5  ligh t  u p when  a  dri ve  is  
    connec te d and  blink s when  there ’s  drive  a ctiv it y .
    J 3 –  E rro r L ED
    P 5  –    error  L E D  fo r e S ATA  h ost por t
    P 0, P 1, P 2, P 3 & P 4 -  error  L E D  fo r por t 0 , 1 , 2 , 3 , 4  &  5
    J 3          J1
    E rro r L ED      Act iv it y  L ED
    P4  P3  P2  P1  P0  P 5P4  P3  P2  P1  P0  P5
    1       2       3       4       5SW 1
    BZS  EZ     M2    M 1    M 0
    OFF
    OFF
    OFF
    OFF
    OFF 
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    Sett ing  or M odi fy ing  th e R AID  M ode U sing  th e J M ic ro n 
    H W  R AID  M an ag er U tili ty  P ro gram :
    1.  For W indow s u sers , in stall  th e J M ic ron  H W  R AID  Manager  lo ca te d o n th e  
      SATA  Con troller  C D. In  th e C D, g o to  Con figura tion  U tili tie s >  JM B393 . T his   
      manager  can  b e use  to  crea te  and  moni to r th e s ta tu s o f th e R AID  volume .
      It is  r e commended  to  u se  th e d efaul t fa cto ry  R AID  D IP  s w it c h  s e tting  when   
      using  th e J M ic ron  H W  R AID  Manage r.
    2 .  Modify  th e R AID  mode  o n th e 5-por t H PM -X U  u sing  D IP  swi tc h
      Recommended  to  b e u se d o n opera ting  s y ste m  w it hou t JMicron  H W  R AID   
      Manager  s uppor t lik e  Linu x, Mac  & Solaris. Window s u se rs  can  a ls o  u se  th e  
      procedure  belo w.
    N ote:  S te p s A  t o  D  n eed  t o  be p erf orme d eac h t im e t h e r a id  mode is  m odi fie d .
      a.  Set th e D IP  swi tc h  to  fa cto ry  d efaul t s e tting . 
     
      b.  Pre ss  th e R AID  s e tting  b utto n w it h  a  ball  poin t pen .
      c.  While  pre ssing  th e R AID  s e tting  b utto n turn  o n th e sys te m  power   
       where th e H PM  is  connec te d. T he b uzzer  will  s ound  while  holding  th e  
       RAID  s e ttin
    g  b utto n. Release  it  a fte r a t leas t 5  seconds  fo r hardware   
       initiali za tion . A  s ingle  beep  will  b e heard  to  indi ca te  ini tiali za tion  is   
       complete d. T he above  s teps  a ct a s a  rese t.
      d.  Power  o ff  th e s ys te m  powe r.
    1        2       3       4       5SW 1
    BZS  EZ     M2    M 1    M 0
    OFF
    OFF
    OFF
    OFF
    OFF 
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
      e.  On the  DIP  s witch , change  (M0 to M2) s etting t o the   
       desired  RAID  mode  using t he diagram  below.
       A ll settings  on the diagram  shows
       •  Error  buzzer f unction is EN ABLED
       •  EZ function  is  DISABL ED .
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    RAID 0  M ode
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    Clone  M ode
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    RAID 1&  RAI D 10  Mode
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    Larg e M ode
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    RAID 3  M ode
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    Individual Dri ves  Mode
    1      2       3      4      5SW1
    BZS  EZ    M2   M1   M 0
    RAID 5  M ode
    OFF
    OFF
    ON
    ON
    ON
    OFF
    OFF
    ON
    ON
    OFF
    OFF
    OFF
    ON
    OFF
    OFF
    OFF
    OFF
    OFF
    ON
    OFF OFF
    OFF
    OFF
    ON
    ON
    OFF
    OFF
    ON
    OFF
    ON
    OFF
    OFF
    OFF
    OFF
    OFF 
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    f.  Pre ss th e R AID  s e ttin g b utto n w it h  a  b all  p oin t p en.
    g .  While  press in g th e R AID  s e ttin g b utto n tu rn  o n th e s yste m  p ow er  
      where  th e H PM  is  c o nnecte d. T he b uzze r w ill  s o und w hile  hold in g th e  
      RAID  s e ttin g b utto n. Rele ase  it  a fte r a t le ast 5  seco nds fo r hardw are   
      in it ia liz a tio n. A  sin gle  b eep w ill  b e h eard  to  in dic a te  in it ia liz a tio n is   
      comple te d. 
    h .  Verif y  if  th e R AID  a rra y is  d ete cte d b y th e s yste m .
    i .   If t
    h e 5 -p ort H PM -X U  is  c o nnecte d to  th e m otherbo ard  onbo ard   
      SATA , o n th e C M OS s e tu p u tilit y , th e r a id  a rra y w ill  d is p la y a s  
      “A ddonic s H /W  R AID 5” if  s e tu p a s a  R AID 5 a rra y.
    j .   If t h e 5 -p ort H PM -X U  is  c o nnecte d to  a n e S ATA  h ost c o ntrol le r c a rd ,  
      on th e R AID  BIOS , th e r a id  a rra y w ill  d is p la y a s “ A ddonic s H /W   
      RAID 0” if  s e tu p a s a  R AID 0 a rra y.
    k .  If b oote d in to  W in dow s, in  D is k D riv e s u nder D evic e  Man ager,  th e
      
      ra id  a rra y w ill  d is p la y a s “ A ddonic s H /W  L A R G E” if  s e tu p a s a   
      LA R G E a rra y.
    l .   Once  r a id  a rra y is  v e rif ie d, y o u c a n s e t th e b uzze r e it h er O N o r O FF.
    1        2        3        4        5S W 1
    BZS  EZ     M 2   M 1   M 0
    RAID  1 &  R AID  1 0 M ode
    1       2        3        4        5S W 1
    BZS  EZ     M 2   M 1   M 0
    Clo ne M ode
    W hen 2  dri ve s a re  
    c o nnecte d to  th e H PM -X U , 
    a nd D IP  s w it c h  is  s e t to  th is  
    s e ttin g, th e 2  dri ve s w ill  b e 
    c o nfigu re d a s a  2 -d riv e  
    R AID 1 a rra y.
    C lo ne’s  a ctio n is  simi la r to  
    R AID 1. H ow eve r,  a ll  o f th e 
    h ard  dri ve s w ill  b e mirro re d. 
    C lo ne m ode is  u se fu l 
    especia lly  w hen u se rs  lik e  
    t o  c o py d ata  fr o m  a  sou rc e  
    h ard  d riv e  to  th e d riv e s 
    c o nnecte d to  th e H PM -X U .
    RAID  S ettin g N ote s:
    W hen 4  d riv e s a re  c o nnecte d to  th e H PM -X U , th e 4  d riv e s w ill  b e 
    c o nfigu re d a s a  4-dr iv e  R AID 10 a rra y. 
    						
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    Note s o n S pare  D riv es u sin g t h e E asy R AID  S ettin g ( E Z)
    W hen E Z fu nctio n is  E N ABLE D , th e a uto-rebu ildin g to  spar e d riv e  is  a uto m atic .
    T he d egrade d R AID  grou p wil l  s ta rt rebu ildin g a uto m atic all y b y usin g th e exi stin g 
    spar e driv e.
    *  S par e d riv e  c a n b e e it h er p lu gge d a ft e r R AID  b uildin g o r a  n ew  driv e c a n b e plu g 
    a s th e spar e driv e whe n R AID  r e buil d is  r e quire d.
     
     
     
      When  w ill r e b uild  a ctio n s ta rt ?
      •  When th e rai d fa ils  a nd E Z is  e nable d, th e
     H PM -X U  wil l     
       auto m aticall y r e buil d th e R AID  grou p usin g th e spar e.
      •  When th e rai d fa ils  a nd E Z is  d is able d, th e H PM -X U  wil l  N O T  
        re buil d th e rai d grou p u nles s y o u in sta ll  a  goo d driv e to  r e plac e th e  
       faile d d riv e .
     
     
     
    C
    onnectin g t h e P ow er C ab le  a n d R AID  T o w er t o  t h e        
    C om pute r
    a.  Conne ct th e powe r cor d p ro vide d fr o m  th e wal l 
      outle t to  th e bac k o f th e to w er.
    b .  Make  s u re  th e powe r is  o ff  ( p owe r L E D  lig ht  
      shoul d b e o ff ) .
    c . 
      
     
     
    P ow er o n/o ff  c o ntr o l
    a.  A mai n powe r s w it c h  is  lo ca te d a t th e bac k o f  
      th e to w er.  T urn  th e s w it c h  o n. A noth er a uxilia ry  
     
      sw it c h  is  lo ca te d o n th e fr o nt o f th e to w er.
    b .  Make  s u re  th e powe r is  o ff  o n th e a uxilia ry    
      sw it c h  ( p owe r L E D  lig ht s houl d b e o ff ) .
    c .  Powe r o n th e to w er. 
    Connect either the USB 3.0 or eS ATA  cable 
    from the back of the tower to a USB 3.0 or 
    eSA TA  connector on the compute r.
    P ow er
    Conn ector
    P
    ow er
    S w it c h
    USB  3.0 Port
    eSATA Port
    Power Button
    Power LED 
    Light 
    						
    							www.addonics.com
    Phone:   408-573-8580
    Fax:     408-573-8588
    Email:   http://www.addonics.com/sales/query/
    CONTACT US 
    						
    All Addonics Technologies manuals Comments (0)

    Related Manuals for Addonics Technologies RAID Tower IV RTIV535HEU3 user guide web