Addonics Technologies External DigiDrive Flash Reader AEPUDDU user guide

							www.addonics.com
Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v7.1.11
T E C H N O L O G I E S
User Guide
Pocket Ultra DigiDrive
(AEPUDDU  / AEPUDDU9  / AEPUDDSA  / AEPUDDSA9)         
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Any flash media below is compatible to use with the Pocket Ultra Digidrive, 
using the optional Addonics CF DigiAdapter and 4-in-1 DigiAdapter or 
equivalent third party adapter.
Note:   The Pocket UDD is not compatible with Wireless Broadband card,    
  Panasonic P2 card, SRAM card and Linear Memory card.
Back
Front
LED
Flash Media Slot
Eject Button5V Power Input
USB Port
MDCF-ICF-II
MSSMSDMMC
ATA FlashPCMCIA Hard Drive
XD Memory AdapterXD
CF DigiAdapter
4-in-1 DigiAdapter 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Driver Installation
For Win98 and Win98SE Note:  Plug and Play under Windows Me, 2000 and XP
  Uses Mass Storage Driver under Windows Me, 
  Windows 2000 and XP (Plug and Play)
1.  Make sure your computer is up and running
2.  Verify that all cables are connected.
3.  Insert the Flash card that you will be using to the Digidrive.
4.  Connect the USB cable to the USB Port.
5.  A New Hardware Found message shall pops up. 
  a.  Follow the ON SCREEN wizard and point to the location of A:\USBWIN98 for the  
  driver.
  b.  Let Windows finish the installation and that’s it.
  c.  Double click My Computer icon and see if you have an extra drive letter \
for the  
    Pocket Ultra Digidrive.
  You may now access the Pocket Ultra Digidrive.
Operation of Pocket UDDThe pocket UDD is designed not to draw any power when there is no media \
inserted. So the LED light will 
remain off even the device is connected to the computer. 
Use the following procedures to add or remove the media from the Pocket \
UDD.
1.  Insert the media fully into the device, the LED light will turn green, i\
ndicating the media is  
  properly inserted inside and the device is now turned on. Your operating system will report new  
  hardware detected and begin to install the device. This may take a few seconds before a new  
  drive icon appears in the My Computer folder. During this initialization, the LED light on the  
  Pocket UDD toggles between orange and green color; and will stay green o\
nce the computer  
  recognizes the media.
2.  Once the drive icon appears, the media is now ready and can be used like\
 regular floppy  
 media.
3.  During the read / write operation, the LED light of the Pocket UDD will \
turn Red.
4.  To remove the media, click on the Safe Remove icon to stop the connection\
 as shown below.  
  Once the “you may now safely remove window” shows up, you can then\
 remove the media  
  from the Pocket UDD by pushing on the eject button. 
  Note: if you eject the media from the Pocket UDD without checking the Sa\
fe Remove icon, a  
  warning message will appear from Windows 98SE, Me and 2000. This message is a reminder  
  that it is safer to use the Safe Remove icon when you remove the media t\
o prevent possible  
  data loss in case you are in the middle of copying a file to and from th\
e media. You can go  
  ahead and close this message.
5.  After the media is ejected from the Pocket UDD, the LED light will go of\
f, indicating the media  
  is fully ejected from the device. 
6.  Do not pull the media out of the device without using the eject button. \
This may crash the  
  computer, as it does not realize the media has been manually removed from the de\
vice. 
						

							www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US