Addonics Technologies 19 Hard driveSSD Duplicators M2HU9HS2S User Manual

							www.addonics.com
1:9 M2 /SSD/HDD HS
Duplicator PRO
(M2HU9HS-2S)
Technical Support
If you need any assistance to get your unit functioning properly, please have
your product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/ 
						

							Overview
 
1www.addonics.com
Technical Support (M-F 8:30 am – 6:00 pm)
WARNING: Please remember 
to set the power supply to 
your local outlet voltage prior 
to plugging in the power 
cord. Failure to do so may 
damage the power supply.
Power Switch Power Connector
Power SelectCooling Fans
Source Select 
Jumper3.5” Source
2.5” Source
Ta r g e t s
Power Button
To Controller Not Used
2.5” Source 3.5” Source
Control Panel
Source Select Jumper
NOTE: The provided jumper MUST be 
connected between “To Controller” and 
either of the two source connectors.
2.5 M2 (NGFF) SSD drive (Qty. 10) 
						

							M.2 Installation
Phone: 408-453-6212 Email: www.addonics.com/support/query/    2
Step 1. For 80mm device, remove 
the screw from the 80mm Standoff 
before proceeding. Otherwise, place 
Metal Standoff over mounting hole 
for 30mm, 42mm, or 60mm device.
Note: An extra screw and standoff 
are provided, when installing 60mm 
or 80mm media, remove the extra 
parts.
Step 3. Secure the device in place 
with the mounting screw.
80mm StandoffMetal Standoff 
						

							Connecting the Power Cable and Powering On
a. Connect the power cord provided from the wall outlet to the back of the tower.
b. Turn on the main power switch on the rear of the chassis.
c. Push the power button on the front of the unit to turn on the HDD duplicator.
Quick Start
By  default,  the  duplicator  will  initialize,  scan  for  drives  and  offer  the  copy  function.  Insert
the source and target drives, power up the unit, wait for the copy function to appear, then
press ENT.
Canceling Functions
When selecting menu options, canceling is done by pressing ESC. When the unit is busy
performing an operation such as copy, verify, or overwrite, the operation can be canceled
by holding the ESC button until the unit beeps.
Duplicator Functions
The  duplicator  has  three  menu  sections:  The  Main  menu,  Setup  Options,  and  Advanced
Setup  Options.  Setup  Options  is  accessed  through  the  Main  menu.  Advanced  Setup
Options is accessed by holding the ESC button from any other menu until the unit beeps.
When the duplicator completes some of the functions it will record a log of the most recent
activity. Select VIEW LOG from the Main Menu to review the latest functions results.
Main Menu
1. Copy HDD
Scans the ports, then copies from the source to any targets found.
2. Async Copy HDD
Scans  the  ports,  then  copies  from  the  source  to  any  targets  found.  More  drives  may  be
added  before  the  process  is  complete,  they  will  begin  the  process  as  soon  as  they  are
detected.
3. Compare HDD
Scans the ports, then any targets found will be compared to the source.
4. Async Compare
Scans  the  ports,  then  any  targets  found  will  be  compared  to  the  source.  More  drives  to
compare  may  be  added  before  the  process  is  complete,  they will  begin  the  process  as
soon as they are detected.
5. PreScan Source
Reads all blocks on the source drive to confirm no I/O errors are encountered.
6. ReScan BUS
Manually scans all ports and reports how many units were found.
3www.addonics.comTechnical Support (M-F 8:30 am – 6:00 pm) 
						

							7. Source Size
Examines the source drive and reports total  space  and  space  used,  if  drive  contains
compatible partitions. Press up/down to change display, ESC to exit.
8. Secure Erase
Scans all ports, then erases all data on all connected drives.
NOTE: some drives will remain in a locked state when the process is complete. Drives that
are locked may not appear to an operating system and will cause an I/O error if used as a
target in the duplicator. If this happens, start secure erase again and hold ESC to cancel
the operation a few moments after it begins.
9. Overwrite
Overwrite is used to write data onto the entire hard disk, it will destroy all data on all HDDs
connected  to  the  duplicator  (including  Source  HDD)  by  writing  data  to  all  sectors.  There
are 4 sub-options: One pass (zero), One pass (random), 3 pass and 7 pass.
10. Setup
Enters the Setup menu. See Setup Options.
11 .  Vi ew  L o g
Shows the results from the most recent drive operation, such as copy, overwrite, etc.
12. Adv Setup
Enters  the  Advanced  Setup  Menu.  Only  available  by  holding  ESC  on  any  Main  Menu
option. See Advanced Setup Options.
Phone: 408-453-6212 Email: www.addonics.com/support/query/    4 
						

							Setup options
10-1. Language
Use this option to select the language of the system, currently only English is supported.
10-2. Copy Size
Controls how much of the source drive to use for copy operations, in percentage. Default
setting is ALL (100%).
10-3. Startup Menu
Sets the first menu option to appear after boot. Default setting is Copy HDD.
10-4. Auto Compare
Controls  whether  or  not  targets  are  compared  automatically  when  copy  is  complete.
Default setting is OFF.
10-5. Button Sound
Enables audible beep when pressing buttons. Default setting is ON.
10-6. Device Info
Displays information about connected drives. Main display is drive manufacturer and size.
Press  up/down  to  select  drives,  ENT  to  display  model  number  and  firmware  revision  of
selected drive.
10-7. System Info
Displays firmware version and date.
10-8. Fast Copy
When  this  setting  is  ON,  the  duplicator  will  attempt  to  copy  the  source  drives  contents
instead of the entire disk. Also controls Compare function. Default setting is OFF.
NOTE: Target drive size is still required to be equal to or greater than source. Only works
with  source  drives  formatted  using  Master  Boot  Record.  If  the  source  drive  has  a  boot
record  other  than  MBR,  the  entire  disk  will  be copied  as  if  Fast  Copy  were  OFF.  If  the
source drive is formatted with a Master Boot  Record  and  contains  only  FAT32  or  NTFS
partitions,  identical  partitions  will  be  created  on  the  target(s)  and  only  the  files  will  be
copied. If the source drive with MBR format includes partitions other than FAT32 or NTFS,
all sectors of all partitions (including FAT32 and NTFS) will be duplicated.
Enabling Fast Copy may not produce bootable duplicates.
10-9. Auto Start Drive
When  source  drive  is  present,  inserting  a  target  drive  will  cause  copy  process  to  begin
automatically. Default setting is OFF.
10-10. Auto Start Timer
Sets  delay  in  time  after  target  insertion  before  beginning  auto  copy  process  if  Auto  Start
Drive is ON. Default setting is OFF (no delay).
5www.addonics.comTechnical Support (M-F 8:30 am – 6:00 pm) 
						

							10-11. Tolerance Size
Sets the minimum target size in percentage compared to the source that is allowed to use
for copying. Default is 100% (equal in size).
NOTE:  Leaving  this  setting  at  100%  or  using  for  minor  adjustments  only  is  strongly
recommended.  Permitting  target  size  less  than  source  size  may  result  in  inaccurate
copies.
10-12. BootTime Delay
This option is used to set boot delay time. Default setting is 5 seconds.
10-13. Quick Compare
Sets  Compare  function  to  stop  after  a  small  amount  of  data  has  been  verified,  up  to
100MBytes. Default setting is OFF.
10-14. Copy with Size
Causes  duplicate  drive  to  report  to  an  operating  system  the  exact  same  total  size  as
source  when  copy  is  complete.  Works  only  on  drives  formatted using a Master Boot
Record. Default setting is OFF.
Phone: 408-453-6212 Email: www.addonics.com/support/query/    6 
						

							Contact Us
Advanced Setup Options
12-01. Read Error Skip
Allows duplicator to ignore I/O errors while reading source drive. Default setting is OFF.
12-02. Update Firmware
Used to apply firmware updates. Connect a drive formatted as FAT containing one partition
with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a drive that is as
small as possible is strongly recommended.
12-03. Compare Firmware
Used  to  confirm  correct  firmware.  Connect  a drive formatted as FAT  containing  one
partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a drive that is as
small as possible is strongly recommended.
12-04. Quick Erase HDD
Scans the ports, then quickly erases all sectors on all connected drives.
12-05. Full Erase HDD
Scans the ports, then completely erases all sectors on all connected drives.
12-06. H/W Diagnostic
Starts comprehensive tests for Ram, LCD, buttons, ports and Flash.
12-07. Load Default
Resets all configuration settings to default.
12-08. Copy HPA
Enables copy functions to duplicate the source drives Host Protected Area. Normally this
area is defined as not available to a host controller as defined by ATA/SATA specifications.
12-09. Burn In
Runs  a  function  continuously  until  aborted. Selections  are  Copy  &  Compare,  Compare,
Async Cpy & Cmp, Async Compare.
www.addonics.com
Phone: 408-573-8580
Fax: 408-573-8588
Email: http://www.addonics.com/sales/query/