Addonics Technologies 15 Hard DriveSSD Duplicators 1 to 5 HDDSSD Duplicator Deluxe C web User Manual

							Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v3.1.11
www.addonics.com
1:5 HDD/SSD Duplicator Deluxe C(HD5SNDXHS, HDUS5SNDX)
T E C H N O L O G I E S
User Guide         
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Drive Installation
The SOURCE drive is the Snap-In Mobile Rack, the TARGET 
drives are the remaining five units below.
1. Be sure all doors are unlocked, use the provided keys to    
    unlock if needed.
2. Gently pull the lever on the door to release it.
3. Insert the drive as shown on the label inside the door: The  
    SATA connector toward the rear. Insert the SOURCE drive 
    with label side on top and the TARGET drives with label side   
    to the right. The drive should slide in easily, dont force it.
4. Close the door on the drive bay. It should also give little 
    resistance, dont force it. It can help to slightly tug the lever 
    while snapping the door shut to make it easier. As soon as 
    the drive is in position it will power up.
5. The SOURCE drive must be locked in place with the 
    provided key to power up. The TARGET drives may be 
    locked in place if desired. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Connecting  th e Power  Cable a nd Powering On
a .Connect the  power cord provided f rom the wall  outlet to  the  back  of the t ower. 
b. Turn on the main power switch on the rear of the chassis.
c. Push the power button on the front of the unit to turn on the HDD dup\
licator.
The  D uplicato r P an el
T here  are four buttons  and an LCD  on the panel  of HDD  Duplic ato r.
1  –  LCD s hows a funct ion or a mess age.
2  –  it  is  used t o s c roll  up f unct ion menus.
3  –  it  is  used t o s c roll  down f unction menus .
4  –  it  is  used t o e xe cu te  a  funct ion.
5  –  it  is  used t o canc el a function.
 
E
N T
ESC
Duplicat or Panel
1
2
34
5
Quick Start
By default, the duplicator will initialize, scan for drives and offer the 
copy function. Insert the source and target drives, power up the unit,  \
wait for the copy function to appear, then press ENT.
Canceling Functions
When selecting menu options, canceling is done by pressing ESC. 
When the unit is busy performing an operation such as copy, verify, 
or overwrite, the operation can be canceled by holding the ESC 
button until the unit beeps.
Duplicator Functions
The duplicator has three menu sections: The Main menu, Setup 
Options, and Advanced Setup Options. Setup Options is accessed 
through the Main menu. Advanced Setup Options is accessed by 
holding the ESC button from any other menu until the unit beeps.
When the duplicator completes some of the functions it will record a 
log of the most recent activity. Select VIEW LOG from the Main 
Menu to review the latest functions results. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Main Menu
1. Copy HDD
Scans the ports, then copies from the source to any targets found.
2. Async Copy HDD
Scans the ports, then copies from the source to any targets found. More \
drives may be added before the process is complete, they will begin the \
process as soon as they are detected.
3. Compare HDD
Scans the ports, then any targets found will be compared to the source.
4. Async Compare
Scans the ports, then any targets found will be compared to the source. \
More drives to compare may be added before the process is complete, 
they will begin the process as soon as they are detected.
5. PreScan Source
Reads all blocks on the source drive to confirm no I/O errors are 
encountered.
6. ReScan BUS
Manually scans all ports and reports how many units were found.
7. Source Size
Examines the source drive and reports total space and space used, if 
drive contains compatible partitions. Press up/down to change display, 
ESC to exit.
8. Secure Erase
Scans all ports, then erases all data on all connected drives.
NOTE: some drives will remain in a locked state when the process is 
complete. Drives that are locked may not appear to an operating system 
and will cause an I/O error if used as a target in the duplicator. If this 
happens, start secure erase again and hold ESC to cancel the opera -
tion a few moments after it begins. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
9. Overwrite
Overwrite is used to write data onto the entire hard disk, it will destr\
oy all 
data on all HDDs connected to the duplicator (including Source HDD) by\
 
writing data to all sectors. There are 4 sub-options: One pass (zero), One 
pass (random), 3 pass and 7 pass.
10. Setup
Enters the Setup menu. See Setup Options.
11. View Log
Shows the results from the most recent drive operation, such as copy, 
overwrite, etc.
12. Adv Setup
Enters the Advanced Setup Menu. Only available by holding ESC on any 
Main Menu option. See Advanced Setup Options.
Setup options
10-1. Language
Use this option to select the language of the system, currently only 
English is supported.
10-2. Copy Size
Controls how much of the source drive to use for copy operations, in 
percentage. Default setting is ALL (100%).
10-3. Startup Menu
Sets the first menu option to appear after boot. Default setting is Copy\
 
HDD.
10-4. Auto Compare
Controls whether or not targets are compared automatically when copy is \
complete. Default setting is OFF.
10-5. Button Sound
Enables audible beep when pressing buttons. Default setting is ON.
10-6. Device Info
Displays information about connected drives. Main display is drive 
manufacturer and size. Press up/down to select drives, ENT to display 
model number and firmware revision of selected drive. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10-7. System Info
Displays firmware version and date.
10-8. Fast Copy
When this setting is ON, the duplicator will attempt to copy the source \
drives contents instead of the entire disk. Also controls Compare function. 
Default setting is OFF.
NOTE: Target drive size is still required to be equal to or greater than 
source. Only works with source drives formatted using Master Boot 
Record. If the source drive has a boot record other than MBR, the entire\
 
disk will be copied as if Fast Copy were OFF. If the source drive is format-
ted with a Master Boot Record and contains only FAT32 or NTFS parti-
tions, identical partitions will be created on the target(s) and only \
the files 
will be copied. If the source drive with MBR format includes partitions \
other than FAT32 or NTFS, all sectors of all partitions (including FAT32 
and NTFS) will be duplicated.
Enabling Fast Copy may not produce bootable duplicates.
10-9. Auto Start Drive
When source drive is present, inserting a target drive will cause copy 
process to begin automatically. Default setting is OFF.
10-10. Auto Start Timer
Sets delay in time after target insertion before beginning auto copy 
process if Auto Start Drive is ON. Default setting is OFF (no delay).
10-11. Tolerance Size
Sets the minimum target size in percentage compared to the source that 
is allowed to use for copying. Default is 100% (equal in size).
NOTE: Leaving this setting at 100% or using for minor adjustments only is 
strongly recommended. Permitting target size less than source size may 
result in inaccurate copies.
10-12. BootTime Delay
This option is used to set boot delay time. Default setting is 5 seconds\
.
10-13. Quick Compare 
Sets Compare function to stop after a small amount of data has been 
verified, up to 100MBytes. Default setting is OFF. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10-14. Copy with Size
Causes duplicate drive to report to an operating system the exact same 
total size as source when copy is complete. Works only on drives format -
ted using a Master Boot Record. Default setting is OFF.
Advanced Setup Options
12-01. Read Error Skip
Allows duplicator to ignore I/O errors while reading source drive. Defau\
lt 
setting is OFF.
12-02. Update Firmware
Used to apply firmware updates. Connect a drive formatted as FAT 
containing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a 
drive that is as small as possible is strongly recommended.
12-03. Compare Firmware
Used to confirm correct firmware. Connect a drive formatted as FAT 
containing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a 
drive that is as small as possible is strongly recommended.
12-04. Quick Erase HDD
Scans the ports, then quickly erases all sectors on all connected drives\
.
12-05. Full Erase HDD
Scans the ports, then completely erases all sectors on all connected 
drives.
12-06. H/W Diagnostic
Starts comprehensive tests for Ram, LCD, buttons, ports and Flash.
12-07. Load Default
Resets all configuration settings to default.
12-08. Copy HPA
Enables copy functions to duplicate the source drives Host Protected 
Area. Normally this area is defined as not available to a host controlle\
r as 
defined by ATA/SATA specifications. 
						

							12-09. Burn In
Runs a function continuously until aborted. Selections are Copy & 
Compare, Compare, Async Cpy & Cmp, Async Compare.
www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US