Home
>
Addonics Technologies
>
HDD Duplicator
>
Addonics Technologies 11 Hard DriveSSD Duplicators HDUS325DX User Manual
Addonics Technologies 11 Hard DriveSSD Duplicators HDUS325DX User Manual
Have a look at the manual Addonics Technologies 11 Hard DriveSSD Duplicators HDUS325DX User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 299 Addonics Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 2
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
Drive Installation
The top enclosure houses the SOURCE drive and the bottom enclosure
houses the TARGET drive.
To install drives, unlock the enclosure using the provided key and gently\
pull
the lever until the door swings open.
For 3.5” installation, insert the drive with the SATA connectors to the rear and
the label side up as shown. For 2.5” drives, follow the steps below t\
o...](http://img.usermanuals.tech/thumb/181/2449/w64_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-1.png "Page 2
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
Drive Installation
The top enclosure houses the SOURCE drive and the bottom enclosure
houses the TARGET drive.
To install drives, unlock the enclosure using the provided key and gently\
pull
the lever until the door swings open.
For 3.5” installation, insert the drive with the SATA connectors to the rear and
the label side up as shown. For 2.5” drives, follow the steps below t\
o...")
![Page 3
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
To install a 2.5” drive into the Snap-In 25 adapter:
Step 1. Gently squeeze the latches on the Snap-In 25 tray and slide it out of
the enclosure.
Step 2. Gently pull the drive retainer clips outward on the tray while inserting\
the drive from the top.
Latches](http://img.usermanuals.tech/thumb/181/2449/w64_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-2.png "Page 3
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
To install a 2.5” drive into the Snap-In 25 adapter:
Step 1. Gently squeeze the latches on the Snap-In 25 tray and slide it out of
the enclosure.
Step 2. Gently pull the drive retainer clips outward on the tray while inserting\
the drive from the top.
Latches")
![Page 4
Step 3. Slide the tray back into the enclosure until the latches snap into
place.
Quick Start
Note: Make sure the TARGET drive is equal to or larger than the SOURCE
drives capacity.
After installing the drives and turning on the Unit, the duplicator will\
beep,
wait for a set delay and display its firmware version. A few moments later it
will display the COPY function. Pressing ENT at this point will begin a copy
operation immediately.
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)...](http://img.usermanuals.tech/thumb/181/2449/w64_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-3.png "Page 4
Step 3. Slide the tray back into the enclosure until the latches snap into
place.
Quick Start
Note: Make sure the TARGET drive is equal to or larger than the SOURCE
drives capacity.
After installing the drives and turning on the Unit, the duplicator will\
beep,
wait for a set delay and display its firmware version. A few moments later it
will display the COPY function. Pressing ENT at this point will begin a copy
operation immediately.
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)...")
![Page 5
Quick Start
By default, the duplicator will initialize, scan for drives and offer the copy
function. Insert the source and target drives, power up the unit, wait \
for the
copy function to appear, then press ENT.
Canceling Functions
When selection menu options, canceling is done by pressing ESC. When the\
unit is busy performing an operation such as copy, verify, or overwrite, the
operation can be canceled by holding the ESC button until the unit beeps\
.
Duplicator Functions
The duplicator has...](http://img.usermanuals.tech/thumb/181/2449/w64_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-4.png "Page 5
Quick Start
By default, the duplicator will initialize, scan for drives and offer the copy
function. Insert the source and target drives, power up the unit, wait \
for the
copy function to appear, then press ENT.
Canceling Functions
When selection menu options, canceling is done by pressing ESC. When the\
unit is busy performing an operation such as copy, verify, or overwrite, the
operation can be canceled by holding the ESC button until the unit beeps\
.
Duplicator Functions
The duplicator has...")
Technical Support If you need any assistance to get your unit functioning properly, please have your product information ready and contact Addonics Technical Support at: Hours: 8:30 am - 6:00 pm PST Phone: 408-453-6212 Email: http://www.addonics.com/support/query/ www.addonics.com T E C H N O L O G I E S HDD Duplicator Deluxe (HDUS325DX) User Guide
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/ Drive Installation The top enclosure houses the SOURCE drive and the bottom enclosure houses the TARGET drive. To install drives, unlock the enclosure using the provided key and gently\ pull the lever until the door swings open. For 3.5” installation, insert the drive with the SATA connectors to the rear and the label side up as shown. For 2.5” drives, follow the steps below t\ o install the drive in the Snap-In 25 adapter, then insert into the enclosure with the SATA connectors to the rear and the “Addonics” side up as shown. Lock \ the enclosure with the provided key - the drive will not power up until the \ enclo - sure is locked.
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/ To install a 2.5” drive into the Snap-In 25 adapter: Step 1. Gently squeeze the latches on the Snap-In 25 tray and slide it out of the enclosure. Step 2. Gently pull the drive retainer clips outward on the tray while inserting\ the drive from the top. Latches
Step 3. Slide the tray back into the enclosure until the latches snap into place. Quick Start Note: Make sure the TARGET drive is equal to or larger than the SOURCE drives capacity. After installing the drives and turning on the Unit, the duplicator will\ beep, wait for a set delay and display its firmware version. A few moments later it will display the COPY function. Pressing ENT at this point will begin a copy operation immediately. www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
Quick Start
By default, the duplicator will initialize, scan for drives and offer the copy
function. Insert the source and target drives, power up the unit, wait \
for the
copy function to appear, then press ENT.
Canceling Functions
When selection menu options, canceling is done by pressing ESC. When the\
unit is busy performing an operation such as copy, verify, or overwrite, the
operation can be canceled by holding the ESC button until the unit beeps\
.
Duplicator Functions
The duplicator has three menu sections: The Main menu, Setup Options, and
Advanced Setup Options. Setup Options is accessed through the Main
menu. Advanced Setup Options is accessed by holding the ESC button from
any other menu until the unit beeps.
When the duplicator completes some of the functions it will record a log\
of
the most recent activity. Select VIEW LOG to review the latest functions
results.
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
The Duplicator Panel
There are four buttons and an LCD on
the panel of HDD Duplicator.
1. LCD shows a function or a
message.
2. Use to scroll up function menus.
3. Use to scroll down function menus.
4. Use to execute a function.
5. Use to cancel a function.
1
EN T
ESC
24
35
Duplicator Panel
Connecting the Power Cable and Powering On
a. Connect the power cord provided from the wall outlet to the back of
the tower.
b. Push the power button to turn on the HDD duplicator.
Main Menu: 1. Copy HDD Scans the ports, then copies from the source to any targets found. 2. Compare HDD Scans the ports, then any targets found will be compared to the source. 3. PreScan Source Reads all blocks on the source drive to confirm no I/O errors are encoun- tered. 4. ReScan BUS Manually scans all ports and reports how many units were found. 5. Source Size Examines the source drive and reports total space and space used, if drive contains compatible partitions. Press up/down to change display, ESC to exit. 6. Setup Enters the Setup menu. See Setup Options for details. 7. USB Mode Not supported. 8. Fast Copy When this setting is ON, the duplicator will attempt to copy the source drives contents instead of the entire disk. Also controls Compare function. Default setting is OFF. NOTE: Target drive size is still required to be equal to or greater than source. Only works with source drives formatted using Master Boot Record. If the source drive has a boot record other than MBR, the entire disk will be copied as if Fast Copy were OFF. If the source drive is formatted with a Master Boot Record and contains only FAT32 or NTFS partitions, identical partitions will be created on the target(s) and only the files will be copied. If the source drive with MBR format includes partitions other than FAT32 or NTFS, all sectors of all partitions (including FAT32 and NTFS) will be duplicated. Enabling Fast Copy may not produce bootable duplicates. 9. Adv Setup Enters Advanced Setup Options menu. Only available when holding ESC on any main menu option. See Advanced Setup Options. www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/ Setup Options: 6-01. Language Use this option to select the language of the system, currently only Eng\ lish is supported. 6-02. Copy Size Controls how much of the source drive to use for copy operations, in per\ cent - age. Default setting is ALL (100%). 6-03. Startup Menu Sets the first menu option to appear after boot. Default setting is Copy\ HDD. 6-04. Auto Compare Controls whether or not targets are compared automatically when copy is \ complete. Default setting is OFF. 6-05. Copy with Size Causes duplicate drive to report to an operating system the exact same t\ otal size as source when copy is complete. Works only on drives formatted using a Master Boot Record. Default setting is OFF. 6-06. Button Sound Enables audible beep when pressing buttons. Default setting is ON. 6-07. Device Info Displays information about connected drives. Main display is drive manuf\ ac - turer and size. Press up/down to select drives, ENT to display model number and firmware revision of selected drive. 6-08. System Info Displays firmware version and date. Advanced Setup 9-01. Detect HDD Delay Sets delay between attempts to detect disk connection or disconnection. \ Default setting is 4 seconds. 9-02. Read Error Skip Sets whether a sector or block may be skipped if a read error occurs on \ the source drive. Default setting is OFF. 9-03. Update Firmware Used to apply firmware updates. Connect a drive formatted as FAT contain- ing one partition with the firmware file in the root directory. NOTE: This function scans the entire disk before proceeding. Providing a drive that is as small as possible is strongly recommended. 9-04. Compare Firmware Used to confirm correct firmware. Connect a drive formatted as FAT contain- ing one partition with the firmware file in the root directory. NOTE: This function scans the entire disk before proceeding. Providing a drive that is as small as possible is strongly recommended. 9-05. Quick Erase HDD Scans the ports, then quickly erases all sectors on all connected drives\ . 9-06. H/W Diagnostic Starts comprehensive tests for LCD, SDRAM, HDD ports, and Flash memory. 9-07. Load Default Resets all configuration settings to default. 9-08. Link Option Enables USB Mode option on the Main Menu. This feature is not supported. Default setting is ON. 9-09. USB Auto-Link Automatically enables USB Mode. This feature is not supported. Default setting is ON. 9-10. COPY HPA Enables copy functions to duplicate the source drives Host Protected Area. Normally this area is defined as not available to a host controller as d\ efined by ATA/SATA specifications.
Main Menu: 1. Copy HDD Scans the ports, then copies from the source to any targets found. 2. Compare HDD Scans the ports, then any targets found will be compared to the source. 3. PreScan Source Reads all blocks on the source drive to confirm no I/O errors are encoun- tered. 4. ReScan BUS Manually scans all ports and reports how many units were found. 5. Source Size Examines the source drive and reports total space and space used, if drive contains compatible partitions. Press up/down to change display, ESC to exit. 6. Setup Enters the Setup menu. See Setup Options for details. 7. USB Mode Not supported. 8. Fast Copy When this setting is ON, the duplicator will attempt to copy the source drives contents instead of the entire disk. Also controls Compare function. Default setting is OFF. NOTE: Target drive size is still required to be equal to or greater than source. Only works with source drives formatted using Master Boot Record. If the source drive has a boot record other than MBR, the entire disk will be copied as if Fast Copy were OFF. If the source drive is formatted with a Master Boot Record and contains only FAT32 or NTFS partitions, identical partitions will be created on the target(s) and only the files will be copied. If the source drive with MBR format includes partitions other than FAT32 or NTFS, all sectors of all partitions (including FAT32 and NTFS) will be duplicated. Enabling Fast Copy may not produce bootable duplicates. 9. Adv Setup Enters Advanced Setup Options menu. Only available when holding ESC on any main menu option. See Advanced Setup Options. www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/ Setup Options: 6-01. Language Use this option to select the language of the system, currently only Eng\ lish is supported. 6-02. Copy Size Controls how much of the source drive to use for copy operations, in per\ cent - age. Default setting is ALL (100%). 6-03. Startup Menu Sets the first menu option to appear after boot. Default setting is Copy\ HDD. 6-04. Auto Compare Controls whether or not targets are compared automatically when copy is \ complete. Default setting is OFF. 6-05. Copy with Size Causes duplicate drive to report to an operating system the exact same t\ otal size as source when copy is complete. Works only on drives formatted using a Master Boot Record. Default setting is OFF. 6-06. Button Sound Enables audible beep when pressing buttons. Default setting is ON. 6-07. Device Info Displays information about connected drives. Main display is drive manuf\ ac - turer and size. Press up/down to select drives, ENT to display model number and firmware revision of selected drive. 6-08. System Info Displays firmware version and date. Advanced Setup 9-01. Detect HDD Delay Sets delay between attempts to detect disk connection or disconnection. \ Default setting is 4 seconds. 9-02. Read Error Skip Sets whether a sector or block may be skipped if a read error occurs on \ the source drive. Default setting is OFF. 9-03. Update Firmware Used to apply firmware updates. Connect a drive formatted as FAT contain- ing one partition with the firmware file in the root directory. NOTE: This function scans the entire disk before proceeding. Providing a drive that is as small as possible is strongly recommended. 9-04. Compare Firmware Used to confirm correct firmware. Connect a drive formatted as FAT contain- ing one partition with the firmware file in the root directory. NOTE: This function scans the entire disk before proceeding. Providing a drive that is as small as possible is strongly recommended. 9-05. Quick Erase HDD Scans the ports, then quickly erases all sectors on all connected drives\ . 9-06. H/W Diagnostic Starts comprehensive tests for LCD, SDRAM, HDD ports, and Flash memory. 9-07. Load Default Resets all configuration settings to default. 9-08. Link Option Enables USB Mode option on the Main Menu. This feature is not supported. Default setting is ON. 9-09. USB Auto-Link Automatically enables USB Mode. This feature is not supported. Default setting is ON. 9-10. COPY HPA Enables copy functions to duplicate the source drives Host Protected Area. Normally this area is defined as not available to a host controller as d\ efined by ATA/SATA specifications.
www.addonics.com Phone: 408-573-8580 Fax: 408-573-8588 Email: http://www.addonics.com/sales/query/ CONTACT US Main Menu: 1. Copy HDD Scans the ports, then copies from the source to any targets found. 2. Compare HDD Scans the ports, then any targets found will be compared to the source. 3. PreScan Source Reads all blocks on the source drive to confirm no I/O errors are encoun- tered. 4. ReScan BUS Manually scans all ports and reports how many units were found. 5. Source Size Examines the source drive and reports total space and space used, if drive contains compatible partitions. Press up/down to change display, ESC to exit. 6. Setup Enters the Setup menu. See Setup Options for details. 7. USB Mode Not supported. 8. Fast Copy When this setting is ON, the duplicator will attempt to copy the source drives contents instead of the entire disk. Also controls Compare function. Default setting is OFF. NOTE: Target drive size is still required to be equal to or greater than source. Only works with source drives formatted using Master Boot Record. If the source drive has a boot record other than MBR, the entire disk will be copied as if Fast Copy were OFF. If the source drive is formatted with a Master Boot Record and contains only FAT32 or NTFS partitions, identical partitions will be created on the target(s) and only the files will be copied. If the source drive with MBR format includes partitions other than FAT32 or NTFS, all sectors of all partitions (including FAT32 and NTFS) will be duplicated. Enabling Fast Copy may not produce bootable duplicates. 9. Adv Setup Enters Advanced Setup Options menu. Only available when holding ESC on any main menu option. See Advanced Setup Options. Setup Options: 6-01. Language Use this option to select the language of the system, currently only Eng\ lish is supported. 6-02. Copy Size Controls how much of the source drive to use for copy operations, in per\ cent - age. Default setting is ALL (100%). 6-03. Startup Menu Sets the first menu option to appear after boot. Default setting is Copy\ HDD. 6-04. Auto Compare Controls whether or not targets are compared automatically when copy is \ complete. Default setting is OFF. 6-05. Copy with Size Causes duplicate drive to report to an operating system the exact same t\ otal size as source when copy is complete. Works only on drives formatted using a Master Boot Record. Default setting is OFF. 6-06. Button Sound Enables audible beep when pressing buttons. Default setting is ON. 6-07. Device Info Displays information about connected drives. Main display is drive manuf\ ac - turer and size. Press up/down to select drives, ENT to display model number and firmware revision of selected drive. 6-08. System Info Displays firmware version and date. Advanced Setup 9-01. Detect HDD Delay Sets delay between attempts to detect disk connection or disconnection. \ Default setting is 4 seconds. 9-02. Read Error Skip Sets whether a sector or block may be skipped if a read error occurs on \ the source drive. Default setting is OFF. 9-03. Update Firmware Used to apply firmware updates. Connect a drive formatted as FAT contain- ing one partition with the firmware file in the root directory. NOTE: This function scans the entire disk before proceeding. Providing a drive that is as small as possible is strongly recommended. 9-04. Compare Firmware Used to confirm correct firmware. Connect a drive formatted as FAT contain- ing one partition with the firmware file in the root directory. NOTE: This function scans the entire disk before proceeding. Providing a drive that is as small as possible is strongly recommended. 9-05. Quick Erase HDD Scans the ports, then quickly erases all sectors on all connected drives\ . 9-06. H/W Diagnostic Starts comprehensive tests for LCD, SDRAM, HDD ports, and Flash memory. 9-07. Load Default Resets all configuration settings to default. 9-08. Link Option Enables USB Mode option on the Main Menu. This feature is not supported. Default setting is ON. 9-09. USB Auto-Link Automatically enables USB Mode. This feature is not supported. Default setting is ON. 9-10. COPY HPA Enables copy functions to duplicate the source drives Host Protected Area. Normally this area is defined as not available to a host controller as d\ efined by ATA/SATA specifications.