Addonics Technologies 11 Hard DriveSSD Duplicators HDMU3 web User Manual

							T E C H N O L O G I E S
Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
www.addonics.com
User Guide
Mini HDD Duplicator Station
(HDMU3, HDMU3-X)         
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Unpacking and Overview
Drive slots: Insert hard drive with SATA connector facing down and on the left side. 
For 2.5” drives and smaller media installed in adapters, insert the d\
rive thorough the 
slot in the top of the unit. For 3.5” drives, insert the drive by pre\
ssing it through the door 
on the top of the unit.
Clone Button
Disk 2
Drive Slot Disk 1
Drive Slot
Back-up button Progress LEDs Eject Buttons
Disk 1 LED Power LED Disk 2 LED
Power
Switch
USB 3.0
Connector
Power Supply Connector
Power Cable USB 3.0 Cable 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Eject buttons: Press down firmly to unseat the drive from the SATA connector 
inside the unit.
Power LED: Glows to indicate the unit is powered up.
Disk LED (Disk1 and Disk2): Glows to indicate a drive is connected and powered 
up, blinks to indicate activity.
Duplication Progress LEDs: When connected to a USB host, these blink in 
unison to indicate I/O activity. With no host connected, they will remain dark until a 
copy operation is started.
Clone Button: Press and hold for three seconds to start copying from Disk1 to 
Disk2, when no USB host is connected.
Backup Button: Press to launch the HDMU3 backup utility.
Disk Cloning
1. Be sure to insert the SOURCE drive into the Disk1 slot and the TARGET drive 
    into the Disk2 slot.
2. The TARGET drive must be equal to or greater than the capacity of the 
    SOURCE drive.
3. Power up the unit with the SOURCE and TARGET drives inserted and the USB 
    cable disconnected, then wait a few moments for the drives to become\
 ready.
4. Press and hold the Clone button for three seconds.
The unit will then blink the Disk1 and Disk2 LEDs to indicate activity, then if no 
errors occur, the Progress LEDs will begin flashing in a back-and-forth pattern, and\
 
as the process completes past each percentage on an LED, that LED will g\
low 
steadily and the remaining LEDs will continue the pattern. When all four\
 LEDs are 
glowing steadily, the process is complete.
If there is an error after starting the copy process, all four Progress \
LEDs will blink 
rapidly in unison, and the LED associated with the drive having a proble\
m will 
remain dark. For example, if the TARGET drive is not equal to or greater than the 
capacity of the SOURCE, holding the Clone button will cause all four Pro\
gress 
LEDs to blink rapidly, the Disk1 LED will be glowing, and the Disk2 LED will be 
dark.
Using the One-Touch Backup Feature
The backup utility is provided on CD or download with its own user guide\
. Once 
installed and the backup settings are in place, pressing the Backup butt\
on will 
launch the backup utility from the system tray and begin the backup proc\
ess 
automatically. 
						

							www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US