AdderLink XD150FX Manual
Have a look at the manual AdderLink XD150FX Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 78 ADDER manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
20 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX This chapter contains a variety of information, including the following: • Getting assistance - see right • Appendix 1 - Options port pin-out • Appendix 2 - Open source licenses • Safety information • Warranty • Radio frequency energy statements GETTING ASSISTANCE If you are still experiencing problems after checking the information contained within this guide, then we provide a number of other solutions: • Online solutions and updates – www.adder.com/support Check the Support section of the adder.com website for the latest solutions and firmware updates. • Technical support – www.adder.com/contact-support-form For technical support, use the contact form in the Support section of the adder.com website - your regional office will then get in contact with you. Further information HT
21 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX 16 OPTIONS APPENDIX 1 - OPTIONS PORT PIN-OUT The OPTIONS port uses a 6p6c socket. The pin-out is listed below. Note: Although the pin labeled ‘Not used’ is inactive, it is still connected internally and so no links should be made at all to this pin. Pin Signal Direction 1 CTS1 / RXD2 Input to the module 2 RXD1 Input to the module 3 TXD1 Output from the module 4 RTS1 / TXD2 Output from the module 5 Not used 6 GND Reference for all signals
22 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX APPENDIX 2 - OPEN SOURCE LICENSES This product includes binaries that are derived from the open source community. ====== lwIP is licenced under the BSD licence: Copyright (c) 2001-2004 Swedish Institute of Computer Science. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ====== jsmn is licenced under the MIT license: Copyright (c) 2010 Serge A. Zaitsev Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies\ or substantial portions of the Software. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON- INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
23 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX WARRANTY Adder Technology Ltd warrants that this product shall be free from defects in workmanship and materials for a period of two years from the date of original purchase. If the product should fail to operate correctly in normal use during the warranty period, Adder will replace or repair it free of charge. No liability can be accepted for damage due to misuse or circumstances outside Adder’s control. Also Adder will not be responsible for any loss, damage or injury arising directly or indirectly from the use of this product. Adder’s total liability under the terms of this warranty shall in all circumstances be limited to the replacement value of this product. If any difficulty is experienced in the installation or use of this product that you are unable to resolve, please see the Getting assistance section. SAFETY INFORMATION • For use in dry, oil free indoor environments only. • Warning - live parts contained within power adapter(s). • No user serviceable parts within power adapter(s) - do not dismantle. • Plug the power adapter(s) into socket outlets close to the module that they are powering. • Do not use an unearthed power socket or extension cable. • Do not use a power adapter if its case becomes damaged, cracked or broken or if you suspect that it is not operating properly. • Replace the power adapter(s) with a manufacturer approved type only. • If you use a power extension cord with the module, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating. Also, make sure that the total ampere rating of all the devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating. • Do not attempt to service the modules yourself.
24 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX RADIO FREQUENCY ENERGY All cables used with this equipment must be shielded in order to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances. European EMC directive 2014/30/EU This equipment has been tested and found to comply with the limits for a class A computing device in accordance with the specifications in the European standard EN55032. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference with one or more of the following measures: (a) Reorient or relocate the receiving antenna. (b) Increase the separation between the equipment and the receiver. (c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. (d) Consult the supplier or an experienced radio/TV technician for help. FCC Compliance Statement (United States) This equipment generates, uses and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a class A computing device in accordance with the specifications in Subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area may cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Canadian Department of Communications RFI statement This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par le ministère des Communications du Canada.
25 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX Web: www.adder.com Contact: www.adder.com/contact-details Support: www.adder.com/support www.ctxd.com Documentation by: © 2016 Adder Technology Limited All trademarks are acknowledged. Part No. MAN-XD150FX-ADDER • Release 1.0a
26 INSTALLATION CONFIGURATION OPERATION FURTHERINFORMATION INDEX HT A Audio receiver 12 transmitter 8 C Connections overview 6 D DDX Matrix accessing 15 Default mode 19 DHCP 16 E EDID management 12 F Firmware upgrade 17 G Gateway 16 I Indicators 18 IP Address 16 M MAC Address 16 N Net Mask 16 Network port temporary connection 15 P Power receiver 14 transmitter 11 R Reset button 3 Resetting 19 RS232 9,13 S Safety information 23 Serial port receiver 13 transmitter 9 U USB receiver 13 V Video receiver 12 transmitter 8 W Warranty 23 Index