ADDERLink INFINITY Manual V33

20
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
9 For installations that require multiple RX units to receive the same feeds, for either 
video or audio or both, then you need to configure the Multicast Settings section.
 The Video and Audio sub-sections are configured in exactly the same way:
•  First, tick the Enable Multicast Video / Enable Multicast Audio check box.
•  Next, enter appropriate Multicast Addresses for the Video/Audio data stream(s). 
The set of IP addresses between...

21
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
PERFORMING AN UPGRADE
ALIF units are flash upgradeable using the method outlined here. However, for larger 
installations we recommend that you use the AdderLink Infinity Manager (A.I.M.) 
to upgrade multiple ALIF units. When using the method below, the ALIF unit will be 
upgraded in sequence.
IMPORTANT: Upgrades must be performed on both the transmitters and 
the receivers at the same time. Mixed firmware operation is not supported....

22
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
In operation, many ALIF installations require no intervention once configured. The TX and 
RX units take care of all connection control behind the scenes so that you can continue 
to work unhindered. 
FRONT PANEL INDICATORS
The six front panel indicators on each unit provide a useful guide to operation:
Operation
Indicators
These six indicators clearly show the key aspects of operation:
• NET  On when valid network link is present.
• SER...

23
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
This chapter contains a variety of information, including the following:
• Getting assistance - see right
• Appendix A - Transmitter (TX) unit configuration pages 
• Appendix B - Receiver (TX) unit configuration pages
• Appendix C - Tips for success when networking ALIF units
• Appendix D - Troubleshooting
• Appendix E - Glossary
• Appendix F - RS232 ‘null-modem’ cable, General specifications.
• Safety information
• Warranty
• Radio...

24
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
APPENDIX A  - Transmitter (TX) unit configuration pages
This section covers the browser-based configuration utility for the AdderLink Infinity TX 
(transmitter) unit. The TX utility has ten pages, titled as follows:
• System Configuration • System Messages
• Video Configuration  • Statistics
• USB Settings  • Firmware Upgrade
• Security  • Reboot
• AIM Manager • About   

25
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
Unit NameName details that you can alter to distinguish this unit from all others. The name entered here will be read by A.I.M. units (if used) for administration purposes.
Unit DescriptionAllows you to optionally add a description of the unit, such as its location. Useful when many ALIF units are being used.
System IP AddressEnter the address that you wish to use for this transmitter. The default is 169.254.1.33 which is the zero config IP...

26
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
TX Video Configuration 
Peak bandwidth limiter percentageThe TX unit will employ a ‘best effort’ strategy in sending video and other data over the IP network. This means it will use as much of the available network bandwidth as necessary to achieve optimal data quality, although typically the TX unit will use considerably less than the maximum available. In order to prevent the TX unit from ‘hogging’ too much of the network capacity, you...

27
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
TX USB Settings 
Enable Dummy Boot KeyboardWhen ticked, the TX unit reports a virtual dummy boot keyboard to the attached PC to ensure that a keyboard is always reported when the PC boots up. The dummy boot keyboard uses one of the 13 USB endpoints, therefore if all 13 endpoints are required elsewhere for USB devices (or a KVM switch only supports two HID devices) then it can be disabled by deselecting this option. See also Reserved Port...

28
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
TX AIM Manager 
Enable AIM ControlClick this button to allow an A.I.M. (Adder Infinity Manager) box to take control of this TX. When the button is clicked, the TX unit will be rebooted to allow the A.I.M. box to discover and control it.
TX System Messages 
Enable system messagesTick to allow the creation of status and error messages by the unit.
Send system messages to remote Log ServerChoose this option to send the system messages to a...

29
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
TX Statistics 
TX Firmware Upgrade
TX Reboot
UpgradeUse this page to upgrade the main or backup firmware image on the unit. Please see the section Performing an upgrade for details.
Reboot Use this page to perform a reboot or a factory reset. Please see the section Manual factory reset for details.
To get here1 If not already connected, temporarily connect the AdderLink Infinity unit and a PC via a network.2 Run a web browser and enter the...