ADDERLink DV104T Manual

							30
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
RADIO FREQUENCY ENERGY
A Category 5 (or better) twisted pair cable must be used to connect the units in order 
to maintain compliance with radio frequency energy emission regulations and ensure a 
suitably high level of immunity to electromagnetic disturbances.
All other interface cables used with this equipment must be shielded in order to maintain 
compliance with radio frequency energy emission regulations and ensure a suitably high 
level of immunity to electromagnetic disturbances.
European EMC directive 2004/108/EC
This equipment has been tested and found to comply with the limits for a class A 
computing device in accordance with the specifications in the European standard 
EN55022. These limits are designed to provide reasonable protection against harmful 
interference. This equipment generates, uses and can radiate radio frequency energy 
and if not installed and used in accordance with the instructions may cause harmful 
interference to radio or television reception. However, there is no guarantee that 
harmful interference will not occur in a particular installation. If this equipment does 
cause interference to radio or television reception, which can be determined by turning 
the equipment on and off, the user is encouraged to correct the interference with one 
or more of the following measures: (a) Reorient or relocate the receiving antenna. 
(b) Increase the separation between the equipment and the receiver. (c) Connect 
the equipment to an outlet on a circuit different from that to which the receiver is 
connected. (d) Consult the supplier or an experienced radio/TV technician for help. 
FCC Compliance Statement (United States)
This equipment generates, uses and can radiate radio frequency energy and if not 
installed and used properly, that is, in strict accordance with the manufacturer’s 
instructions, may cause interference to radio communication. It has been tested and 
found to comply with the limits for a class A computing device in accordance with 
the specifications in Subpart J of part 15 of FCC rules, which are designed to provide 
reasonable protection against such interference when the equipment is operated in a 
commercial environment. Operation of this equipment in a residential area may cause 
interference, in which case the user at his own expense will be required to take whatever 
measures may be necessary to correct the interference. Changes or modifications not 
expressly approved by the manufacturer could void the user’s authority to operate the 
equipment.
Canadian Department of Communications RFI statement
This equipment does not exceed the class A limits for radio noise emissions from digital 
apparatus set out in the radio interference regulations of the Canadian Department of 
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites 
applicables aux appareils numériques de la classe A prescrites dans le règlement sur le 
brouillage radioélectriques publié par le ministère des Communications du Canada.   
						

							31
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
www.ctxd.com Documentation by:
© 2014 Adder Technology Limited
All trademarks are acknowledged.
Part No. MAN-ALDV104T-ADDER • Release 1.0c
Web:  www.adder.com
Contact:  www.adder.com/contact-details
Support: forum.adder.com   
						

							32
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
HT
A
API specification  25
Auto
mode  3,15
B
Bracket
rack mount  7
Brackets
fitting  7
C
Cable  23
Cloned
EDID  16
Connections
overview  7
transmitter - power in  11
D
Default
EDID  16
resetting  22
DHCP  17
Disable all Screens  16
Dual source  15
Dual source mode  3
DV100R  2,10
DV120R  2,10
E
EDID  16
Edit User  18
Enable all Screens  16
Error symbols  13
F
Fixed
mode  3,15
H
HDMI
connections  8
indicators  8
inputs  4
I
Input source
alternative  20
L
Link output ports  4
Logon Security  17
M
Managing  19
N
Network
cable  23
connection  9
port  4
rescan  20
settings  17
Network port
temporary connection  12
O
Options port  4
P
POD Manager
accessing  12
Power adapter
connection  11
input  4
R
Rack fascia plate  6,7
Rack mounting  7
Rear mounting slot  7
Receiver configuration  14
Receiver connections  10
Rescan
network  20
Resetting defaults  22
RJ45 connector  23
S
Safety information  29
Screened/Unshielded Twisted 
Pair  23
Shielded Twisted Pair  23
Single source  15
Single source mode  3
Slot
rear mounting  7
Solid cables  23
S/STP  23
STP  23
Stranded cabling  23
S/UTP  23
T
Transmitter configuration  15
Transparent
EDID  16
Troubleshooting  22
U
Upgrade  18
User
settings  18
W
Warranty  29
Index