Adams Amplifier S4XV User Manual

							EA-SX
Operation Manual / BedienungsanleitungEnglish / Deutsch
EXTERNAL AMP UNIT 
						

							2
Please read the following safety instructions \fefore setting up your system. 
\beep the instructions for further reference. Please heed t\che warnings and fol-
low the instructions.Caution: To reduce the risk of e\clectric shock, do not open the\c amplifier 
unit. There are no user-servicea\fle parts inside. Refer servicing  to quali-
fied service personnel.
This product, as well as all attached extension cords, \fust be ter\finated with 
an earth ground three-conductor \bC \fains power cord like the one supplied 
with the product. To prevent shock hazard, all three co\fponents \fust always 
be used.
Never replace any fuse with a value or type other than those specified. Never 
bypass any fuse.
\blways switch off your entire syste\f before connecting or disc\nonnecting any 
cables, or when cle\naning any co\fponents.
Do not place this unit on an unstable cart, stand or tripod, bracket or table. The 
unit \fay fall, causing seriou\ns injury and/or serious da\n\fage. When cart is used, 
use caution when \foving the cart/apparatus co\fbination.
Do not expose this product to rain or \foisture, never wet the inside with any 
liquid and never pour or spill l\niquids directly onto this unit. Please do\n not put 
any objects filled wi\nth liquids (e.g. vases, etc.) onto the speaker.
Check if the specified voltage \fatches the voltage of the power supply you use. 
If this is not the case do not conne\nct this unit to a power source! Please contact 
your local dealer o\nr national distributor.
CautionRisk of electrical shockDo not open
Risque de shock electrique Ne pas ouvrier
CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE BACK COVER OR ANY OTHER PART. NO USER-SERVICABLE PARTS INSIDE.
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL.
Safety Instructions   
						

							3
EA-SX Manual / English
Protect the cord fro\f being walked on or pinched.
\blways use fully checked cables. Defective cables can har\f your speakers. They 
are a co\f\fon source for any kind of noise, hu\f,\n crackling etc.
When installing the unit \fake sure there is adequate ventilation. I\fproper venti-
lation will cause o\nverheating and can da\n\fage the unit.
\blways keep electrical equip\fent out of the reach of children.
\blways unplug sensitive electronic equip\fent during lightn\ning stor\fs.
To co\fpletely disconnect fro\f \bC \fains, disconnect \nthe power supply fro\f the 
\bC receptacle.   
Never use fla\f\fable or \nco\fbustible che\ficals for cleaning audio co\n\fponents. 
Never expose this product to extre\fely high or low te\fperatures. Never 
operate this product in an explosi\nve at\fosphere.
Safety Instructions   
						

							4
Ta\fle of contents
 
Safety Instructions ..................\n..................\n......... 2-3
1.   Introduction  ..................\n..................\n..................\n. 5
2.  Quick Start   ..................\n..................\n..................\n.. 6
2.1  I\fportant Infor\fation   ..................\n..................\n... 6
2.2  Connecting the ext. a\fp unit to the \fonitors   ... 6
3.  Speaker Installation  ..................\n..................\n....... 7
3.1  General  reco\f\fendations  ..................\n..............7
3.2  Flush \founting the \fonitors  ..................\n...........7
4.  Speaker \bdjust\fent   ..................\n..................\n...... 8-9
4.1  The Front Control Panel  ..................\n..................\n.8
4.2  Standby Switch and LEDs  ..................\n................8
4.3  Input Controls  ..................\n..................\n................ 9
4.4  Bass Controls   ..................\n..................\n................ 9
4.5  Tweeter Controls ..................\n..................\n............ 9
5.  Troubleshooting  ..................\n..................\n............. 10 
5.1  No or distorted signal  ..................\n..................\n.... 10
5.2  Parasitic noises  ..................\n..................\n............. 10
6.  Maintenance  ..................\n..................\n..................\n 11
7.   Shipping / Packaging   ..................\n..................\n.... 11
8.  Environ\fental Infor\fation   ..................\n.............. 11
9.  EU Declaration of Confor\fity  ..................\n..........12
10 .   Li\fited Warranty   ..................\n..................\n........... 13
10.1  Ter\fs and Conditions  ..................\n..................\n.... 13
10.2  How to clai\f  ..................\n..................\n..................\n 13
11 .   Technical Data  ..................\n..................\n............... 14   
						

							5
EA-SX Manual / English
1. Introduction
Dear custo\fer,
Thank you for choosing the \bD\bM \budio External \b\fplifier Unit.
The  \bD\bM  External  \b\fplifier  Unit  E\b-SX  has  been  designed  for  driving  the  following 
studio \fonitor \fodels externally in order to be able to  flush \fount these \fonitors into 
the control roo\f wall: S2X,  S3X-H, S3X-V, S4X-H, S4X-V, S5X-H, S5X-V.
The 19“ / 3U rack unit contains the sa\fe electronic circuitry together with the 
co\fprehensive control setting options o\nf the a\fplifiers that can be found in all SX 
\fonitors  listed above.
This \fanual is intended to provide you with infor\fation about the External \b\fp Unit and 
the SX \fonitors you are driving with it. It contains 
important information regarding 
safety, setting up, handling, and warranty. We request that you read these sections 
carefully to ensure easy set up and p\nrevent potential proble\fs.
If  you  have  any  questions  about  this  or  any  of  our  products,  please  don’t  hesitate  to 
contact us – we will be happy to assist you.
For  detailed  infor\fation  concerning  \bD\bM’s  technologies  and  products,  co\fplete 
reviews,  and  a  list  of  worldwide  \bD\bM  users  and  studios,  please  visit  our  website: 
www.adam-audio.com
You are invited to share your experience with our products by joining us on Facebook 
and  also, if you don’t want to \fiss out on the latest info  on \bD\bM Professional \budio, 
co\fe and  follow us on Twitter!
We  hope  very  \fuch  that  you  enjoy  your  new  loudspeakers  and  the  external  a\fp  unit 
E\b-SX and wish you \fany delightful hours with the\f.
Your \bD\bM \budio Tea\f   
						

							6
2.1 Important Information for set up
We reco\f\fend using high q\nuality XLR cables \nto guarantee opti\fal perfor\fance.
We reco\f\fend that you retain the original packaging, as it is the best  way to 
guarantee safe transportation should the need to do so arise.
 
Please note  that with the use  of the EA-SX e\fternal amp unit the option to retro\bt 
the SX monitors  with  the ADAM DA-SX 24 bit/192 kHz D/A converter will not be 
available anymore.
2.2  Connecting the external amp unit to the monitors
a)  Before connecting the loudspeakers to the 19” external a\fp unit \fake sure that 
your audio source is switched off.
\f)  Connect each \fonitor to one E\b-SX a\fp unit  by using one Speakon cable. You 
can order cables in either 5 or 10 \feter lengths fro\f \bD\bM \budio.  
	 Please note that in order to connect the monitors to the e\fternal amp unit you mus\Xt 
use the ADAM Audio ready-made Speakon cables.
Attention owne\fs of the S5X-H\b 
You will find two Speakon  jacks on each \fonitor that have to be connected to 
one E\b-SX a\fp unit per \fonitor. Please \fake sure you do not cross the two 
cables while connec\nting the\f to the  external a\fp unit. The respective Speakon 
jacks on both the \fonitors and the external a\fp unit are labelled with Speakon 1 
and Speakon 2 and have to be connected correspondingly.
c)    Connect your \fixing desk/D\bW to one E\b-SX per \fonitor channel using the XLR 
connector on the back panel of the external a\fp unit.
d)  Check if the specified voltage \fatches the voltage of the power supply you use. If 
this is not the case do not conne\nct the E\b-SX to a power source! Please contact 
your local dealer o\nr national distributor. 
If the voltages \fatch, use the included power cables to connect the E\b-SX to the 
\bC socket.
e)    Power on the external a\fp unit at the back panel first and then at the front    
  (Standby switch). 
f)    Turn on your audio source and adjust the volu\fe carefully.
2. Quick Start   
						

							7
EA-SX Manual / English
3.1 
General recommendations
Please \fake sure that there are no obstacles in the way fro\f  the \fonitor to your ears. 
You should be able \nto see the speakers co\fpletely. 
The loudspeakers should be aligned\n with the listener’s position.
Please note that vibrating parts of nearby objects can \fask \nthe sound.
Mechanical adjustments: If you plan to \fodify the speaker cabinet (e.g. dr\nilling 
holes), please cont\nact us before doing so. Usually, we will handle your warranty 
obliging.
3.2  Flush mounting the \cmonitors
Should  you  consider   to  flush  \fount  your  \fonitors,  this  would  bring  so\fe  acoustical 
benefits.  Cabinet  edge  diffraction  and  also  low  frequency  reflections  that  would 
nor\fally occur fro\f the wall behind the speaker can be avoided that way. The result is  
an i\fproved \fid and low frequency response.
Regarding the orientation of the \fonitors please \fake sure  the  acoustical axis of  each 
\fonitor  points  directly  to  the  listening  position.  In  larger  control  roo\fs   the  \fonitors 
should be  angled in the vertical plane so that the acoustic axis  \feets in the \fiddle of 
the standing and seated listening position. In the horizontal plane  the \fonitors should 
be   placed  according  to  the  standard  stereophonic   (60°  between  L/R  channels)  or 
\fultichannel (ITU-R BS.775\n-1) setup reco\f\fendations.
Fo\f  fu\fthe\f  info\fmation  on  installation  we  \fecommend   contacting  an  acoustics 
specialist o\f  a p\fofessional \feco\fding studio design/const\fuction company.
3. Speaker Installation   
						

							8
4.1  The front control panel
On the front of the a\fp unit you will find a contr\nol panel that allows detailed 
fine-tuning of your loudspeakers to your particular roo\f acoustics and personal 
listening preferences. The following tips are intended to assist you at using the 
controls in the best \fanner. 
Please note that using the controls \fay have a great i\fpact on the overall sound 
characteristics  of  your  loudspeakers.  We  reco\f\fend  using  the  controls  with   
ut\fost care and only after several audio tests with fa\filiar recordings.
4.2   Stand\fy switch and LEDs
While the \fain power switch can be found on the rear of 
the external a\fp unit, there is also a switch for power on/ 
standby on the front panel. In standby \fode, the switch glows 
orange, in power on \fode it glows green.
To the right of the standby switch you can find 
two LEDs:
•  In case of an overload, the OL LED will flash  red. The protective circuit  will safe 
your speaker fro\f da\fage. 
•  The D/A LED on the E\b-SX is without function as the D/\b converter option is not 
available with the use of the external a\fp unit. 
 
4. Speaker Adjustment   
						

							9
EA-SX Manual / English
4.3 
Input Controls
There are two different  controls to regulate the overall input
sensitivity:
•  One control allows for coarse settings  fro\f -20dB to +8dB. The 
control works in 4dB steps.
•  The other control is intended for \bne tuning in 0.5dB steps, 
ranging fro\f -1.5dB to 2dB. 
4.4  Bass Controls
There are two different  controls to regulate the lower 
frequencies:
•  The EQ 80 Hz control is a bell equalizer to boost bass response.
•  The 6  kHz control is a shelf filter that allows to progressively 
raise or lower the frequencies above 6 kHz (see Fig.). 
4. Speaker Adjustment
Room EQ \b kHz     
						

							10
\bll \bD\bM products are designed and \fanufactured  to the highest quality 
standards.  However, if any proble\fs with your speaker occur, we reco\f\fend 
to proceed as follows:
5.1 P\foblem: The LED shows nor\fal operation (green) but there is either no 
or on\fy a d\bstorted aud\bo s\bgna\f.
If both (all) speaker channels are affected, the reason can probably  be 
found within the signal path. If only one speaker is affected, the proble\f 
will probably be within  this speaker or the external a\fp unit.
a)  Check the wiring. 
Is the cable defective? \bre all cables connec\nted correctly?
\f)  Check the signal path.
Interchange the cables of both external a\fp units. Does the  proble\f 
change with one of the cables?
Connect the external a\fp units as directly to the signal source as pos-
sible. Is another part of the signal path (e.g. \fixer, subwoofer) defective?
If the answer to all these questions is ‘no’, the proble\f is being cause\nd 
by the loudspeaker or the external a\fp unit with the ut\fost probability.
If the answer to at least one of these questions is ‘yes’, there will prob-
ably be another defective device within the signal path.
5.2  P\foblem: You hear paras\bt\bc  no\bses (like  hu\f\fing, buzzing, so\nughing,   
cracking).
Please disconnect t\nhe signal cables.
If the noises disappear\n, check the signal path.
If the noises can still be heard, check for other electrical devices close to 
the speakers (\fobile phones, s\nwitching power supplies, etc.). If there is 
no interfering device the speaker will probably cause the proble\f.
5. Trou\fleshooting