Adam Equipment PMB Moisture Analyser PMBIT User Manual

© 2013 Adam Equipment   
 
Adam Equipment 
 
 
 
 
PMB Moisture Analyzer (EN) 
PMB Analizzatore d’umidita’ (IT) 
 
(P.N. 3076610544, RevisionC3, July 2013) 
 
 
 
 
 
 
 
Adam Equipment strives to be more environmentally focused and uses recycled materials and 
environmentally friendly packaging where possible. As part of this initiative we have developed a short 
form manual that uses less paper and ink to describe the main functions of your new Adam moisture 
analyzer. A complete version is available...

© 2013 Adam Equipment 
ENGLISH:      P  1  -  20 
ITALIANO:      P  21  -  40 
EU DECLARATION: P  41
C  O  P Y  

EN 
© 2013 Adam Equipment 1 3076610544, RevisionC3, July 2013 
SAFETY 
 
This Moisture Analyzer complies with the European Council Directives and international 
standards for electromagnetic compatibility, and safety requirements.  
·  Improper use or handling can result in damage or injury.  
·   To prevent damage to the equipment, read these operating instructions thoroughly. Keep 
these instructions in a safe place.  
·   The Moisture Analyzer is used for determination of the moisture in samples. Do...

EN 
© 2013 Adam Equipment 2 3076610544, RevisionC3, July 2013 
1.0  CONTENTS 
SAFETY .................................................................................................................................................. 1 
HOT SURFACES ................................................................................................................................ 1 
MATERIALS...

EN 
© 2013 Adam Equipment 3 3076610544, RevisionC3, July 2013 
2.0  OPERATION 
2.1  TURNING ON THE ANALYZER  FOR THE FIRST TIME 
 
Set your analyzer  in a well ventilate room and away from any flammable substances. Ensure that you 
are using the correct voltage for the analyzer. The voltage is shown on the back of the unit. 
 
The master on /off switch is located on the back. To turn on 
the unit press the  on / off switch at the rear of the analyzer, 
the display will show the serial number and software...

EN 
© 2013 Adam Equipment 4 3076610544, RevisionC3, July 2013 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  S\fNGLE  ºC 
 123 
RAMP ºC  RAMP T\fME 
 123 
  06:00 
STEP 1 TEMP  ºC  



\f


 100   03:00 
STEP 2 TEMP  ºC  STEP 2  T\fME 
 120 
  03:00 
STEP 3 TEMP  ºC  



\f


 140   03:00 
\fNTERVAL 
SEC 10 
Display shows rESULt 
Options are: Moisture, Solid, ATRO 
Moist, ATRO Solid 
To set a test press the 
[Test] key 
Use arrow keys,  [Dspl] and [Test] ,  
to change...

EN 
© 2013 Adam Equipment 5 3076610544, RevisionC3, July 2013 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
The user can print the current configuration by pressing the  [Print] key during the process providing 
the second function for that key is not needed.  
ST\bP T\fME 
Min 30 
STAB RANGE    stAB time 
    02   sec15  
stop time  stop RANGE  stop time 
min 30      02  sec15  
Display, shows St\bP  
Options are: Time, Stab or Time / 
Stab 
 
Option T\fME 
Will...

EN 
© 2013 Adam Equipment 6 3076610544, RevisionC3, July 2013 
2.3  RUNNING A TEST 
 
Once the test procedure has been set then a test can be run using the current settings. A test can 
also be recalled from memory See USING THE INTERNAL MEMORY. 
 
Place an empty sample pan on the analyzer. 
Press [Tare] to zero the weight.  
 
 
Remove and fill the sample pan with the sample.   
  
Place the filled pan on the analyzer. 
 
Lower the lid of the weighing chamber,     a.  If automatic start has been...

EN 
© 2013 Adam Equipment 7 3076610544, RevisionC3, July 2013 
 
When the test has stopped the beeper will sound 3 short beeps (if enabled) and the display will show 
the end result: 
 
 
 
 
 
This display shows the test was automatically stopped as stability was reached in 12:44 minutes.  If it 
had stopped at the end of the time period it would have TSTOP on the top line and if manually 
stopped it would have MSTOP. 
 
At this time the final results are displayed. These results will include elapsed...

EN 
© 2013 Adam Equipment 8 3076610544, RevisionC3, July 2013 
3.0  USING THE INTERNAL MEMORY SETTING 
 
3.1  STORING  TEST SETTINGS 
 
It will be possible to store up to 49 test procedures/settings. There is also a factory default that is 
permanently stored as PST 00.  
 
To Store the current settings press the  [PST] key. The display will give the user the option to store, 
recall or delete a Preset Test. The display will show 
PST ST\bRE or PST RECALL or PST DELETE. Use 
the up/down arrow keys,...