Adam Equipment MDW Mechanical Physician Scales MDW160MREVB4 User Manual

© Adam Equipment Company 2014 
   
Adam Equipment 
    
 
 
MDW
-160M  
 
MECHANICAL HEALTH AND FITNESS SCALE 
(P.N. 4283, Revision B4, May 2014) 
 
 
               
  
 
     

© Adam Equipment Company 2014 
       
  

                                     © Adam Equipment Company 2014 
 
     
CONTENTS 
      
1.
 INTRODUCTION ...................................... .................................................................... 5 
2. SPECIFICATIONS .................................... .................................................................... 5 
3. INSTALLATION ...................................... ...................................................................... 6 
3.1 GENERAL INSTALLATION...

                                     © Adam Equipment Company 2014 
   

                                     © Adam Equipment Company 2014 
1.  INTRODUCTION 
   
·  The MDW-160M Health and Fitness Scale can weigh a  person as 
well as measure the height. 
 
·  It  is  simple  to  use  and  can  be  moved  around  with  t he  help  of  the 
wheel attachment at the bottom of the scale. 
 
·  The  MDW-160M  scale  is  widely  applicable  for  use  in   business, 
schools, hospitals, clinics and sports departments.    
 
·  A height rod assembly is included as standard. 
 
  
2....

                                     © Adam Equipment Company 2014 
 3.  INSTALLATION 
 
3.1  GENERAL INSTALLATION 
 
This precision instrument is extremely easy to set  up, as all major parts are 
factory pre-assembled.    
Hardware supplied for installation:   
-  6 no. M6 x 12 screws 
-   6 no. M6 Lock washers 
-   2 no. Hex Head screws 
-   Tool (Spanner/Wrench) 
   
 
 
        
 
   
1. Column with head  
2. Height measuring rod 
3. Platform base  
4. Wheel attachment   

                                     © Adam Equipment Company 2014 
NOTE: If the column bracket is bent, straighten it befor e assembling.  
  
Slip the column over the column bracket on the base .  
 
Hold the column straight so that the draft rod fits  into the opening aperture of 
the column bracket.    
Fix the column to the column bracket using two M6 s crews in front of the 
column and four at the back.   
Lay down the scale, with column horizontal to the f loor. 
 
Raise the draft rod keeping out...

                                     © Adam Equipment Company 2014 
·  Insert  the  two  hexagonal  headed  screws  from  the  ha rdware  pack 
into the holes in the front of the column and tight en slightly. 
 
·  Place  both  the  height  rod  clamping  brackets  over  t he  two  pre-
installed hexagonal headed screws and pull it down.  
 
·  Use  the  included  wrench  to  tighten  both  the  screws .  Do  not  over 
tighten the screws. 
     
 
    
A. Latch to lock/unlock the...

                                     © Adam Equipment Company 2014 
simultaneously  pushing  down  the  measuring  arm  until   it  rests 
horizontally upon the top of the person’s head. 
    Read the height of the person as follows:   
·   The rear end of the measuring arm is tapered to po int at the reading 
on the height rods. 
 
·  If the tapered end of the measuring arm points at  the outer height 
rod,  then  the  height  of  the  person  is  same  as  the  r eading  at  this 
point on the outer...

                                     © Adam Equipment Company 2014 
5.  WEIGHING OPERATION 
            
     
 
          
To do the zero setting -  
 
·   For accurate weighing, place the scale on a levell ed floor. 
 
·  Move  both  the  balancing  masses  to zero  when  the sc ale platform 
is empty.  
 
·  If the scale is balanced, the lever will be in the  horizontal position. 
This  will  be  indicated  by  the  arrow  indicator  being   in  line  with  the 
horizontal mark on the right side of...