Adam Equipment Eclipse Precision Balances Eclipse Set Up Guide 5274 28Sep2015

							Part # 3.01.6.6.12085 , Rev 1.0, Sep 2015
Set-Up Guide
www.adamequipment.com  
						

							Precision - 1mg (0.001g)
Precision - 10mg (0.01g) 
						

							Analytical - 0.1mg (0.0001g)
FrontBack 
						

							Set Up
1.
1st2nd
3rd
4th
BackFront
3.
2.
Analytical Remove any transit packaging and protection pieces
Open
Closed
4.
For Eclipse assistance, scan QR code or visit 
www.adamequipment.com/Eclipsesupport 
						

							1.2.
Precision Remove any transit packaging and protection pieces
Precision - Top Loader Remove any transit packaging and protection pieces
1.2. 
						

							Locating the balances
1.
3.
Avoid VibrationsStatic Free Area
2.
4.
Avoid Extreme TemperaturesAvoid Water Contact     
						

							g
Turning on your balance (warm up)
12 Hour 
Warm Up
The balance must be plugged into the mains power and turned on for a minimum of 12 hours , 
prior to any calibration and use. The balance should then be calibrated before use.
External Calibration
Cal
g
Select
Put on weight matching desired calibration weight
Remove the calibration weight
Weight removal is automatically detected Weight is automatically deteced 
and calibration begins100g
100g
g
g
Calibration completeg
✓
For operating and set up videos as well as a complete user’s manual - go to our Eclipse support page: 
www.adamequipment.com/EclipseSupport  
						

							Weighing
Changing weighing units
Unit
Setup
g, kg*, mg*, ct, GN, N, oz, ozt, dwt, lb*, dr, mm, tl T, tI H, tl S, tl, ti, T, Cus Unit 
*kg, lb available for Precision only, mg available for Analytical only.  
						

							Taring the balances
Net    
						

							WARRANTY INFORMATION
Adam Equipment offers Limited Warranty (Parts and Labour) for any 
components that fail due to defects in materials or workmanship.  
 
Warranty starts from the date of delivery.
During the warranty period, should any repairs be necessary, the purchaser 
must inform its supplier or Adam Equipment. The company or its authorised 
technician reserves the right to repair or replace the components at the 
purchaser’s site or any of its workshops depending on the severity of the 
problems at no additional cost. However, any freight involved in sending the 
faulty units or parts to the service centre will be borne by the purchaser.
The warranty will cease to operate if the equipment is not returned in 
the original packaging and with correct documentation for a claim to be 
processed. All claims are at the sole discretion of Adam Equipment.
This warranty does not cover equipment where defects or poor performance 
is due to misuse, accidental damage, exposure to radioactive or corrosive 
materials, negligence, faulty installation, unauthorised modifications 
or attempted repair or failure to observe the requirements and 
recommendations as given in this User Manual.
This product may include a rechargeable battery that is designed to be 
removed and replaced by the user. Adam Equipment warrants that it will 
provide a replacement battery if the battery manifests a defect in materials 
or workmanship during the initial period of use of the product in which the 
battery is installed.
As with all batteries, the maximum capacity of any battery included in 
the product will decrease with time or use, and battery cycle life will vary 
depending on product model, configuration, features, use, and power 
management settings. A decrease in maximum battery capacity or battery 
cycle life is not a defect in materials or workmanship, and is not covered by 
this Limited Warranty.
       
Repair carried out under the warranty does not extend the warranty period. 
 
Components removed during the warranty repairs become the company 
property.
       
The statutory rights of the purchaser are not affected by this warranty. In the 
event of dispute then the terms of this warranty are governed by UK law. For 
complete details on Warranty Information, see the terms and conditions of 
sale available on our web-site.