Acumen Camera NVR Series AiPF4U User Manual
Have a look at the manual Acumen Camera NVR Series AiPF4U User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Acumen manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
AiP -N series 16CH/9 CH/4 CH Manual 30 Insert the IP address of the NVR Once the address has been added it will remain stored for future use Highlight your NVR from the left hand bar and click connect A download panel will then appear. This means the backup manager programme is communicating with your NVR gathering all recorded data. Recorded data will appear on the left hand side. You can access minute breakdowns from the tree. Highlight your required file then click download from the controls at the top Your files will begin to download Downloaded files will show in the Backup Manager programme until deleted
AiP -N series 16CH/9 CH/4 CH Manual 31 12.3 Convert already downloaded files Backup Manager allows you to convert multi channel backups to single channel AVI files. To do this follow the steps below: Open Backup Manager Click file > convert AVI file Locate desired backup files Choose the channels you wish to convert. You can select more than 1 channel. Click OK to start the conversion Th e file will now be saved in your desired location
AiP
-N series 16CH/9 CH/4 CH Manual
32 Quick Installation Guide
This guide has been designed to provide a basic overview of key installation processes. If you require more
detailed instructions, please refer to the full installation guide that follows this section
Chapter 1: Rear Panel
1.1 16CH Rear View
1. External IR receiver (RCA)
7. Aux USB Power
2. RJ - 45 Keyboard - in
Connected from previous DVR’s
keyboard output in daisy chain 8. HDMI Output
3. RJ - 45 Keyboard - out
Connect to the next DVR’s input 9 . LAN / USB Mouse
RJ - 45 connector and USB mouse
4. Alarm I/Os
Alarm 8 input switches, 1 N/O alarm
output, and 1 N/C alarm output 10 . VGA Output
5. RS - 485
For PTZ connection 11. DC 12V Input
6. Audio Output
RCA audio connector 12. eSATA Output
13. Power Switch
AiP
-N series 16CH/9 CH/4 CH Manual
33
1.2 9
CH / 4CH Rear View
1. RJ - 45 Keyboard In 5. Alarm I/Os
Alarm 2 input switches, 1 N/O alarm
output, and 1 N/C alarm output
2. HDMI Output 6. Audio Output
RCA audio connector
3. 12V DC Input 7. eSATA Outpu t
4. LAN / USB Mouse
Network RJ - 45 connector and
USB mouse .
Connect power supply, monitor, network cable and control device
Note: For easy installation, it is recommended that you connect a touch screen monitor or USB mouse.
AiP -N series 16CH/9 CH/4 CH Manual 34 Chapter 2: Hard Drive(s) 2.1 Adding hard drive(s) Please ensure unit is switched off Open unit by removing side and rear screws Add hard drive(s) using the supplied mounting screws and sata/power cables Power Unit Power up unit by turning the switch on the rear to on 2.2 Formatting Hard Drive(s) Enter the setup menu Select system from the left hand options Select HDD info Installed drives will be listed Select drive(s) to format Select enter Select OK to complete Note: If you have purchase a unit with a hard drive installed, please ignore sections 2 and 3. Note: See user guide for how to navigate the system, i.e. menu’s, camera selection etc.
AiP -N series 16CH/9 CH/4 CH Manual 35 Chapter 3: Time and Date Settings Enter the setup menu Select system from the left hand options Select date/time Adjust time and date Select display format Note: See user guide for how to navigate the system, i.e. menu’s, camera selection etc.
AiP -N series 16CH/9 CH/4 CH Manual 36 Chapter 4: Network Settings Enter the setup menu Select network from the left hand options Ensure static is displayed under IP mode Enter your IP address and subnet mask range Note: This guide will refer to a static IP address. For other options, see installation manua l.
AiP -N series 16CH/9 CH/4 CH Manual 37 Chapter 5: Adding Cameras Enter the setup menu Select camera from the left hand options Select WS discovery The NVR will now search the network for installed cameras Select Get Snap to make camera identification easier Assign the relevant cameras to a channel by selecting channel number in right hand camera column Exit menu setup and all installed cameras will be displayed By default they are set to record on schedule 24 hours a day Note: If the IP addresses of the installed IP cameras have not already been configured, they can be changed by highlighting the channel and selecting ‘Set IP’. Note: The installed IP cameras must be set to the same IP range as the NVR.
AiP -N series 16CH/9 CH/4 CH Manual 38 Menu configuration Chapter 1: Setup Menu The setup menu contains menu settings for cameras, monitors, recording, alarm, system, network, and PTZ. The details of all the setup menu items are described in this chapter. 1.1 Camera setup To setup an AiP camera, use the following steps: 1.1 -1 Camera select Use the directional arrows to select camera you wish to edit/add 1.1 -2 Camera name A user can enter up to 16 characters for a camera name. To setup the camera name, type the characters using the virtual keyboard and then press the Enter button Virtual keyboard:
AiP -N series 16CH/9 CH/4 CH Manual 39 1.1-3 Camera source To setup a camera channel, you can select IP cam, demo video or no IP connection from this setting 1.1-4 AiP camera address Once the source is set to an AiP camera, you can enter the IP address of the AiP camera for that specific channel. To manually set the IP address, press Enter to enable editing via the virtual keyboard. You can also use WS-Discovery for automatic IP address setup. 1.1-5 AiP camera HTTP port By default, the NVR AiP camera ‘HTTP’ port is set to 80. This can be changed if requ ired. 1.1-6 Video RTSP port By default, the NVR AiP camera ‘RTSP’ port is set to 554. This can be changed if required. 1.1-7 AiP camera setup