Acumen Camera IP Speed Dome Series AiPY04Z03N2BP User Manual

							 20 
Chapter 3-5-2 Weighted Streaming Mode Weighted streaming mode is activated when an alarm went off.    The streaming goes to the maximum speed, for example 30 FPS.    If there is no alarm activity, the streaming stays one frame per second for saving bandwidth and storage.    
						

							 21 
  
 
Chapter 3-5-3 Video Quality To setup video quality, please adjust brightness, contrast, hue, saturation, and sharpness accordingly. 
 
Chapter 3-6 PTZ Settings To setup PTZ preset points, please select Camera ID (RS-485ID) first.    For RS-485ID, please refer to PTZ user manual for detail.    Once RS-485ID has been set, please select preset point.    Move the lens to desired position by using pan, tilt, and zoom buttons.    Adjust the lens’ iris and focus by using iris and focus buttons.   
  
Chapter 3-6-1 PTZ Advanced Settings For internal PTZ leans settings, information such as AGC mode, white balance, expose mode, shutter speed, back light compensation, digital effect, and reset camera to default can be configured.    For detail setting, please refer to the Speed Dome’s user manual. 
Alarm Interval  
						

							 22 
 
 
 
 
Chapter 3-6-2 PTZ Schedule Settings To setup PTZ scheduling, please select PTZ schedule link.    Use the mouse select on the radio button of the preset types, None, Autopan, Preset #1, Preset #2, Preset #3, and Preset #4. 
Click on the hour of the calendar control to configure the preset action.  
						

							 23 
  
Chapter 3-7 SD Card Recording To record video on SD Card, please insert SD card into the SD card slot.    Enable SD card recording feature.    The AiP camera can start to record video into the SD card.  
Chapter 3-7-1 SD Card Recording Setting For SD card recording setting, please see the following for detail. 
  SD Recording: Enable SD card recording.  Alarm/Motion Triggering: Digital input and motion detection SD card recording.   Recording Time: Post alarm recording time.  Continuous: Continuous recording mode  No Network Activity: If there is no network connection, perform SD recording.  Recording Format: Recording resolution  SD System Status: SD Linux mounting status.  SD Card State: SD card inserting status  SD Card Capacity: SD card total capacity  SD Card Free Space: SD card free space  
						

							 24 
 Mount: Manually mount SD card.  Un-mount: Manually un-mount SD card.  To un-mount the SD card, please click “un-mount SD Card” button.    It might crash the file system of the SD card, if a user does not un-mount the SD card properly. 
  
Chapter 3-8 Alarm Settings H.264 D1 video server or AiP camera’s hardware alarm system contains motion detection, alarm sensors, and one alarm/relay output.    Many alarm features such as motion/alarm email notification and FTP archiving can be found at this section.     
Chapter 3-8-1 Motion/Alarm Setup There are motion detection zones allowed in the H.264 D1 video server or AiP camera.   A user can enable the detection zones with different sensitivities ranging from 1 to 99 (highest to lowest) for motion detection.    Once a suspicious motion activity gets triggered, H.264 D1 video server or AiP camera can start to capture one JPEG snapshot on various recording mediums.  
Chapter 3-8-2 Alarm (DI) Input Detection  Alarm Notification — Enable alarm notification.  Alarm Input Mode — Normal open/normal close for detecting alarm input  Alarm Output Time — Trigger alarm output based on the dwell.  
						

							 25 
 
For video encoder model, since there are two alarm outputs, a user can specify alarm output time.  
Chapter 3-8-3 Motion Area Once above information get set, please configure the motion area of the monitored environment.    To configure motion area, perform mouse click on the video area. 
 
 
Chapter 3-8-4 Audio Detection For audio model, the AiP camera has audio detector detecting acoustic level.    If the volume exceeds the audio sensitivity value, audio detector triggers an alarm for notification.         
						

							 26 
  
Chapter 3-9 Audio Setting Audio setting is based on the following:   MIC Volume: MIC or line input volume  Audio Input Mode: Choose MIC input or Line input.  Audio Input Gain: Voice input gain magnification  Audio Output Volume: Line output volume adjustment  Audio Coding Type: G.711 u-Law  Sample Rate: Audio sample rate  Bit Rate: Audio bit rate. 
 
  
						

							 27 
Appendix  
Advance Network DDNS and PPPoE Technologies 
The advantage of using DDNS and PPPoE is to save the cost of IP address.    H.264 AVC AiP camera’s PPPoE service gets a dynamic global IP address after system reboot.   This IP address may get changed periodically.    This is the address needed to access the video server over Internet.    When ISP re-assigns a new IP address to H.264 AVC AiP camera, H.264 AVC AiP camera notifies DDNS service.    A remote PC can access H.264 AVC AiP camera by typing domain name in a browser.    The domain name gets resolved by DDNS service and gets translated to its dynamic global IP address.    The dynamic global IP address can now be accessed by the remote PC.   
 
  
 
  
 
  
 
 
                          
 
Advance Network Port Forwarding Technology  Port forwarding technology is an advanced network technology which is widely used for using one global IP shared by many network devices.    The network architecture is illustrated as below.    Port 80 of the router (192.168.0.10) is assigned to the device IP address, 192.168.0.10.    Port 81 of the router is assigned to the device IP address, 192.168.0.11.    When Remote PC accesses the router’s port 86 (122.116.191.129), it eventually accesses the video server at 192.168.0.11.   
DDNS Server 
3.  ISP assigns global IP to AIP CAMERA 
Internet 
4.    Access AIP CAMERA using the dynamic global IP address.  
ISP 
Remote PC 
5. Resolve domain name to IP       address and sent back to remote PC. 
1. Get IP address from ISP after reboot. 2. Notify DDNS server for the new IP address if SPEED DOME CAMERA gets reboot or assigned a new IP address.   
						

							 28 
 
 
 
 
 
 
iPhone Access To use Live Cams Pro (Eggman Technologies Inc.) for AI AiP cameras.  Please use your iPhone and select AppStore for download Live Cams Pro application developed by Eggman Technologies Inc.    Execute Live Cams Pro application. Please click on “Add Camera” button on your phone while using Live Cams Pro. Task bar gets prompted as below:  Please selection one of the following drivers for cameras: Profile 1: H.264 HD or D1 AiP camera. 
 
 
 
 
 
  
Android Access Please use your Android phone and select Android Market for downloading IP Cam Viewer/IP Cam Viewer Lite application developed by Robert Chou.  Execute IP Cam Viewer/IP Cam Viewer Lite application. Please click on Setup button on your phone while using IP Cam Viewer/IP Cam Viewer Lite. Task bar gets prompted as below: 
Router’s global IP: NO2.N16.19N.129 
Port 80: 192.168.0.10 Port 81: 192.168.0.11  
http:// 122.116.191.129:86 
 
Internet 
IP: 192.168.0.10 IP: 192.168.0.11    
						

							 29 
 
Please click on Manage Cameras button. A list of camera names shows on the screen. Please select one of the cameras and click on Edit button.  
 
“Add/Edit AiP camera” dialog box gets prompted for editing an AiP camera or a DVR. 
 
In “Add/Edit AiP camera” dialog box, please enter the following information:  
1. Name: Name of the AiP camera or DVR’s camera 2. Category: Please select AI. 3. Type: Select device type, AI D1/ AI HD/AI DVR. 4. IP Address: Please type IP address, for example http://122.116.191.129:86  where 86 is the port number. 5. Provide username and password information. For AiP camera, the default username and password are “admin” and “pass”. For DVR, the default username and password are “admin” and “1111”.  Once above information is entered, please click “Save” button. You are able to see live video of the AiP camera or DVR’s camera.  
Emergency Factory Default 
To restore the server to factory default settings, please: 1.  Hold Load Default Button or short Reset Cable for 10 seconds, then release the button or Reset Cable. 2.  After about 40 seconds, the network LED light is off, and then it becomes lit again. 3.  This camera has completed the factory default setting, and it reboots. 4.  Use IPScan scanning for the IP address of the IP device. 5.  Launch Internet browser for the IP address of the IP device. 6.  Type default username “admin” and password “pass” for enter web interface of the IP device.