Acumen Camera IP Speed Dome Series AiPI34H03N2B User Manual

							  20   
 
 
Preset Go   To
 have the camera move to a specified Preset position, please select the Preset Point from the drop -down Preset 
Point  list. Then the camera shall readily move to the target position.  
 
Chapter 3-6-2 PTZ Advanced Settings  3-
6-2.1 Lens Advance  
Lens Advance Setting Menu can be found under this path:  PTZ> PTZ Advance> Lens Advance 
In the Lens Advance Setup Menu, users can set various Lens  parameters including Focus, Focus 
Sensitivity, Digital Zoom, Zoom Speed and Focus Speed. Each setting is specified as follows: 
  Focus   Auto focus at PTZ or 
auto focus only at zoom operations  
Focus Sensitivity  Focus sensitivity
 (Low:0  ~ High:6)  
Digital Zoom   Enable digital zoom feature after optical zoom.
 
Zoom Speed   Zoom speed adjustment 
Focus Speed
  Focus speed adjustment
 
 
 
 
 
 
 
 
 
 
 
 
 
  1.3MP IP PTZ Interface   
						

							  21   
3-
6-2.2 Pan -Tilt Setup  
Pan-Tilt Setting Menu can be found under this path:  PTZ> PTZ Advance> Pan-Tilt Setup  
In the Pan -Tilt Setup Menu, users can set various Pan-Tilt parameters including Home Position, 
Self Return Time, Self Return Mode and Auto Mode. Each setting is specified as follows: 
  Home Position  Specify home position for one of the presets.
  
Self Return Time  User Define if IP 
Speed Dome idles for a period of time,  the selected function will be activated automat ically. 
Self Return Mode  Return to home 
position at home position, auto scan mode, tour mode, or patrol mode.  Users are able to set an 
operation mode to ensure constant monitoring. If the IP  Speed Dome Camera idles for a period of time, the 
selected functi on will be activated automatically; this is the  Return Mode function. The  Return Mode function 
allows constant and accurate monitoring to avoid the Dome Camera idling or missing events.  
Auto Mode   Specify auto scan mode, tour or patrol for auto Pan mode.
   
  3-
6-2.3  Auto Scan Setup  
Auto Scan Programming can be found under this path:  PTZ> PTZ Advance> Auto Scan Setup 
The IP Speed Dome Camera supports up to Four Auto Scan Paths. Please follow the instructions 
below for Auto Scan Path setup. 
  Auto Scan Setting 
To setup a Auto Scan Path, please first select a path number from the drop-down list. Then move the cursor to 
the PTZ control pane, and move the camera to a desired view (PTZ controls) as the start point of a Auto Scan 
Path. Click on the <
apply> button of < Start Position > and start programming the Auto Scan Path via PTZ 
controls. When finishing programming, click on the < apply> button of  to quit. Then this Auto 
Scan Path will be automatically recorded.  Subsequently, assign a  Dwell Time and A ctive Speed for the current 
position from the drop -down Dwell List and Speed List.    
  3-
6-2.4  Tour Setup  
The Tour Path  Programming can be found under this path:  PTZ> PTZ Advance> Tour Setup  
						

							  22  The IP Speed Dome Camera supports totally 
four Tour Path; each Tour Path consists of up to  32 
Preset Points. Please refer to the instructions below to program a Tour table.   
NOTE: Before setting this function, users must pre-define at least two Preset Points. 
  Tour Path Setting 

  Tour Path 
Please select the number of Tour Path to be set from the drop-down list in the top of the Tour Setup menu. 
   Sequential Preset Points Setting 
Please setup each Preset Point of the programmed Tour Path in order, assigning a Preset Point from the  
list for the specified number of Preset Point. Finally, Click  on the  button  to save the settings mentioned 
above.    
  3-
6-2.5 Patrol Setup   
The Patrol Path  Programming  can be found under this path:  PTZ> PTZ Advance> Patrol Setup 
The IP Speed Dome Camera supports up to four Patrol Paths. Please follow the instructions below 
for Patrol Path setup. 
  Patrol Path Setting 
To setup a Patrol Path, please first select a path number from the drop-down list. Then move the cursor to the PTZ 
control pane, and move the camera to a desired view (PTZ controls) as the start point of a Patrol Path. Click on the 
 button to start record and start programming the Cruise Path via PTZ control. When finishing programming, 
click on the < End> button to quit. Then this Cruise Path will be automatically recorded.   
Chapter 3-6-3 PTZ Schedule Settings 
To setup PTZ scheduling, please select PTZ schedule link.    Use the mouse select on the radio 
button of the preset types, None, Autopan, Preset #1, Preset #2, Preset #3, and Preset #4.  
Click on the hour of the calen dar control to configure the preset action .  
						

							  23   
 
Chapter 3-7 SD Card Recording  To record video on  SD Card, please insert SD card into the SD card slot.    Enable SD card recording 
feature.    The IP camera can start to record video into the SD  card.  
 
Chapter  3-7-1. SD Card Recording Setting 
For SD card recording setting, please see the following for detail.   
 
 
To un -mount the SD card, please click  “un- mount SD Card ” button.    It might crash the file system of 
the SD card, if a user does not un -m ount the SD card properly.      SD Recording:   Enable  SD card recording.  
   Alarm/Motion Triggering:   Digital input   and 
motion detection SD card recording.   
   Recording Time:   Post alarm recording time.  
   Continuous:  Continuous recordi ng mode  
   No Network Activity:   If there is no network 
connection, perform SD recording.  
   Recording Format:  Recording resolution  
   SD System Status:  SD Linux mounting status.  
   SD   Card State:   SD card inserting status  
   SD   Card Capacity :  SD   card total capacity  
   SD   Car d Free Space :   SD   card free space  
   Mount:  Manually   mount SD card.  
   Un - mount:  Manually un - mount SD card.  
  
						

							  24   
 
Chapter 3-8  Alarm Settings 
H.264 D1 video server or IP PTZ camera ’s hardware alarm system contains motion detection, alarm 
sensors , and one  alarm/relay output.    Many alarm features such as motion/alarm email notification 
and F TP archiving can be found at this section.     
 
Chapter 3-8-1 Motion/Alarm Setup 
There are  motion detection zone s allowed in  the H.264 D1 video server or IP PTZ camera .    A user 
can enable the detection zones with different sensitivities ranging from  1 to 99 (highest to lowest) for 
motion detection.    Once a suspicious motion activity gets triggered,  H.264 D1 video server or IP PTZ 
camera  can start to capture one JPEG snapshot  on various  recording mediums . 
 
Chapter 3-8-2 Alarm (DI) Input Detection 
  Alarm Notific ation—Enable  alarm notification.  
   Alarm Input Mode —
Normal open/normal close  for detecting alarm input 
   Alarm Output Time —Trigger alarm output based on the dwell.    
For video encoder model,  since there are two alarm outputs, a user can specify alarm output ti me. 
 
Chapter 3-8-3 Motion Area  
Once above information get set, please configure the motion area  of the  monitored  environment.    To 
configure motion area, perform  mouse click on the video area .  
						

							  25   
 
Chapter 3-8-4 Audio Detection 
For audio model, the IP camera  has audio detector detecting acoustic level.    If the  volume exceeds 
the audio sensitivity value, audio detector triggers an alarm for notification.           
 
Chapter  3-9. Audio Setting 
Audio setting is based on the following:         MIC Volume: MIC or line input volume  
   Audio Input Mode: Choose MIC input or Line input.  
   Audio Input Gain:  Voice input gain magnification  
   Audio Output Volu me: Line output volume 
adjustment  
   Audio Coding Type: G.711 u - Law  
   Sample Rate: Audio sample rate  
   Bit Rate :  Audio bit rate.  
  
						

							  26  Appendix  
Advance Network DDNS and PPPoE Technologies 
The advantage of using DDNS and PPPoE is to  save the cost of IP address.    H.264 AVC IP 
camera ’s PPPoE service gets a dynamic global IP address after system reboot.    This IP address 
may get changed periodically.    This is th e address needed to access the video server over Internet.   
When ISP re -assigns a new IP address to H.264 AVC IP  camera, H.264 AVC IP camera  notifies 
DDNS service.    A remote PC can access H.264 AVC IP  camera by typing domain name in a 
browser.    The domain name ge ts resolved by DDNS service and gets translated to its dynamic 
global IP address.    The dynamic global IP address can now be accessed by the remote PC.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Advance Network Port Forwarding Technology  
  Port forwarding technology  is an advanced network technology which is wid ely used for using one 
global IP shared by many network devices.    The network architecture is illustrated as below.    Port 
80 of the router (192.168.0.1 0) is assigned to the device IP address, 192.168.0.10.    Por t 81 of the 
router is assigned to the device IP address, 192.168.0.11.    When Remote  PC accesses the router’s 
port 8 6 (1 22.1 16.191.129), it eventually accesses the video server at 192.168.0.11.    
 
 
 
 
 
 
 
 
iPhone Access 
To use Live Cams Pro (Eggman Technologies Inc.)  for AI  IP cameras.   
Please  use  your  iPhone  and  select  AppStore  for  download  Live  Cams  Pro  application  developed  by 
Eggman Technologies Inc .   Router’s global IP:  1 2 2.1 16 . 191 .1 29  
Port 80: 192.168.0.10  
Port 81: 192.168.0.11  
  http://122.116.191.129:86  Internet  
IP:   192.168.0.10  IP:   192.168.0.1 1  DDNS Server  
3 .    IS P assigns global IP to  IP  
CAMERA  Internet   4 .    Access  IP  CAMERA using the 
dynamic global IP address.  
 
ISP  Remote PC  
5.   Resolve domain n ame to   IP        
address and sent back   to 
remote   PC.  
1.   Get IP address from ISP after reboot.  
2.   Notify DDNS server for the new IP address if 
SPEED DOME   CAMERA gets reboot or assigned a 
new IP address.  
  
						

							  27   
 
 
 
 
 
 
 
 
Execute Live Cams Pro application. Please click on “Add Camera” button on your phone while using 
Live Cams Pro. Task bar gets prompted as below:   
Please selection one of the following drivers for cameras
: Profile 1: H.264 HD or D1 IP camera. 
 
 
 
 
 
 
 
 
 
 
 
Android Access:  
Please use your Android phone and select Android Market for downloading IP Cam Viewer/IP Cam 
Viewer Lite application developed by Robert Chou. 
 
Execute IP Cam Viewer/IP Cam Viewer Lite application. Please click on Setup button on your phone 
while using IP Cam Viewer/IP Cam Viewer Lite. Task bar gets prompted as below:   
Please click on Manage Cameras button. A list of camera names shows on the screen. Please select 
one of the cameras and click on Edit button.   
     
						

							  28  “Add/Edit IP Camera” dialog box gets prompted for editing an IP camera or a DVR.
 
 
In “Add/Edit IP Camera” dialog box, please enter the following information:   
  1.  Name: Name of the IP camera or DVR’s camera 
2.  Category: Please select AI . 
3.  Type: Select device type,    AI D1 / AI  HD/  AI DVR. 
4.  IP Address: Please type IP address, for example  http://122.116.191.129:86  where 
86 is the  port number. 
5.  Provide username and password information. For IP camera, the default username and 
password are “admin” and “pass”. For DVR, the default username and password are “admin” 
and “1111”. 
 
Once above information is entered, please click “Save” button. You are able to see live video of the IP 
camera or DVR’s camera. 
 
Emergency Factory Default 
T o restore the server to factory default settings, please:  
   
1.  Hold Load Default Button  or short Reset Cable for 10 second s, then release the button or 
Reset Cable.  
2.  After about 40 seconds, the  network LED light is off, and then it becomes  lit again.  
3.  This camera has completed the factory default setting, and it reboots.  
4.  Use IPScan scanning for the IP address of the IP device.  
5.  Launch Internet browser for the IP address of the IP device.  
6.  Type default username “admin” and password “pass” for enter web interface of the IP device.  
 
SD Card Compatibility List  Manufacturer   Size   SDHC /SDSC  
Sandisk   16 GB   SDHC  
Sandisk   8GB   SDHC  
Transcend   8GB   SDHC  
Transcend   4GB   SDHC  
Sandisk   32GB   SDHC   
						

							  29  Specification
 
  Design and specification are subject to change without  further notice. 
  Network Function  
Video compression   H.264 ,  Motion JPEG  
Resolution   1080P(1920x1080),H264 480P(7
20 x 480), JPEG 480P (720 x 480), CIF(352 x 240)  
Frame rate   H.264 : 30 FPS at 1080P
(1920 x 1080 )  
Motio n JPEG : 30 FPS at D1(720 x 480 )  
Video streaming   RTP/HTTP, RTP/TCP, RTP/UDP  
Video bitrate   128Kbps ~  5 Mbps  
Frame rate and bitrate controllable on - the - fly  
VBR / CBR / GOP supported  
Security   Base64 HTTP encryption  
Multiple user access levels with pa ssword protection  
10 user accounts available  
Users   8 simultaneous users  
OSD   Text overlay for date, time, and camera name  
Alarm Function   Image upload over FTP and E - mail by alarm / motion detection  
CPU , memory   Embedded SoC ARM11, 528MHz, 256MB DDR2, 2 56MB flash memory  
Web PTZ control   Pan , tilt , zoom in / out , absolute position, and video - click - n - move  
PTZ  preset scheduling   Yes, via web interface  
Maintenance   Firmware update via HTTP  
Firmware available at web site  
Network Interface   10Mbps/   100Mbp s, RJ - 45  
Client PC requirement   OS : Windows 2000 , Windows XP , Windows Vista, Windows 7  
Browser : Windows Internet Explore r   6, 7, 8  
CPU : Intel Pentium 4 1.8GHz or above  
RAM : 1GB or above, Independent Display Card  
Network protocols   IP,  TCP,  UDP,  HTTP,  SMTP,  NTP,  DDNS,  UPnP,  FTP,  ARP,  DHCP,  PPPoE,  DNS, 
RTSP, RTCP, Telnet, ONVIF  
Mobile phone and PDA   iPhone, iPad, and Android support  
System integration   ONVIF 及 AI   HTTPAPI  
AIM   AIM   HD 2.6   support  
Video display   AI   Universal ActiveX &  AI   Java Applet  
OS   Embedded Linux 2.6.32  
Two - way Audio   G.711