Acumen Camera Dome Series AiPO24V05Y2B User Manual

							Chapter 3-8 Alarm Settings  H.264 FULL HD AiP camera’s hardware alarm system contains motion detection, alarm sensors, and one alarm/relay output. Many alarm features such as motion/alarm email notification and FTP archiving can be found at this section. 
 Chapter 3-8-1 Motion/Alarm Setup  There are motion detection zones allowed in the H.264 FULL HD AiP camera. A user can enable the detection zones with different sensitivities ranging from 1 to 99 (highest to lowest) for motion detection. Once a suspicious motion activity gets triggered, H.264 FULL HD AiP camera can start to capture one JPEG snapshot on various recording mediums. 
 Chapter 3-8-2 Setup for Camera with Alarm Input   Alarm Notification—Enable alarm notification.  Alarm Input Mode—Normal open/normal close for detecting alarm input  Alarm Output Time—Trigger alarm output based on the dwell.   
 
  
 
 For video encoder model, since there are two alarm outputs, a user can specify alarm output time. 
 Chapter 3-8-3 Motion Area  Once above information get set, please configure the motion area of the monitored environment. To configure motion area, perform mouse click on the video area. 
 
 
 
 30  
						

							 
  
 
  
 
  
 
  
 
 Chapter 3-8-4 Face Detection  The video analytics contains face detection engine. There are up to 4 faces can be detected. Each face should be at least 1/20 out of the video size for recognition purpose. Once a face is detected, the alarm output, e-Mail with a snapshot, and/or an FTP snapshot can be triggered. 
 Not detected 1/20 in size 1/10 in size  
 
  
 
  
 
 
 31  
						

							Chapter 3-8-5 Audio Detection  For  audio  model,  the  AiP  camera  has  audio  detector  detecting  acoustic  level.  If the  volume  exceeds  the  audio  sensitivity  value,  audio  detector triggers  an  alarm for notification. 
 
  
 
  
 
  
 
  
 
  
 
  
 
 Chapter 3-8-6 Tampering Detection  The AiP camera’s video analytics engine is able to detect tampering. Tampering detection works (1) lens spray paint prevention, (2) camera move prevention, and  (3) out of focus prevention.   To enable this feature, please set Enable option.  
  
 
  
 32  
						

							 
  
 
 
 Chapter 3-9 Audio Setting  Audio setting is based on the following:  MIC Volume: MIC or line input vo lume  Audio Input Mode: Choose MIC input or Line input.  Audio Input Gain: Voice input gain magnification  Audio Output Volume: Line output volume adjustment  Audio Coding Type: G.711 u-Law  Sample Rate: Audio sample rate  Bit Rate: Audio bit rate. 
 
 
  
 
  
 
  
 
  
 
  
 33  
						

							Appendix  Advance Network DDNS and PPPoE Technologies  The advantage of using DDNS and PPPoE is to save the cost of IP address. H.264 AVC AiP camera’s PPPoE service gets a dynamic global IP address after system reboot. This IP address may get changed periodically. This is the address needed to access the video server over Internet. W hen ISP re-assigns a new IP address to H.264 AVC AiP camera, H.264 AVC AiP camera notifies DDNS service. A remote PC can access H.264 AVC AiP camera by typing domain name in a browser. The domain name gets resolved by DDNS service and gets translated to its dynamic global IP address. The dynamic global IP address can now be accessed by the remote PC. 
 Remote PC  
 DDNS Server  Internet 
 5. Resolve domain name to IP address and sent back to remote PC.. 
 4. Access IP CAMERA using the dynamic global IP address. 
 ISP   
 2. ISP  assigns  global  IP to IP CAMERA  
 1. Get IP address from ISP after reboot.   2. Notify DDNS server for the new IP address if FAST DOME CAMERA gets reboot or assigned a new IP address.  
 
  
 
  
 
 34  
						

							Advance Network Port Forwarding Technology  Port forwarding technology is an advanced network technology which is widely used for using one global IP shared by many network devices. The network architecture is illustrated as below. Port 80 of the router (192.168.0.10) is assigned to the device IP address, 192.168.0.10. Port 81 of the router is assigned to the device IP address, 192.168.0.11. W hen Remote PC accesses the router’s port 86 (122.116.191.129), it eventually accesses the video server at 192.168.0.11. 
 
 
  Internet 
  http:// 122.116.191.129:86 
  Router’s global IP: http:// 122.116.191.129 IP: 192.168.0.11 IP: 192.168.0.10 Port 80: 192.168.0.10   Port 81: 192.168.0.11  Emergency Factory Default  To restore the server to factory default setting, please:  1. Hold Load Default Button or short Reset Cable for 10 seconds, then release the button or Reset Cable.   2. After about 40 seconds, the network LED light is off, and then it becomes lit again.   3. This camera has completed the factory default setting, and it reboots.   4. Use IPScan scanning for the IP address of the IP device.   5. Launch Internet browser for the IP address of the IP device.   6. Type default username “admin” and password “pass” for enter web interface of the IP device.  
 SD Card Compatibility List  
Manufacturer Size SDHC/SDSC Sandisk 16GB SDHC Sandisk 8GB SDHC Transcend 8GB SDHC Transcend 4GB SDHC  35  
						

							Specification     Video compression H.264 and Motio n JPEG, dua l codec  Resolution QXGA(2048 x 1536), 1080P(1920 x 1080), 720P(1280 x 720), D1(720 x 480),  CIF(352 x 240)     Up to H.264 2048x1536 15 FPS (Only 3MP AiP cameras provide)   Up to H.264 1920x1080 30 FPS, H.264 720x480 30 FPS,  Multiple profile JPEG 720x480 25 FPS, JPEG 352x240 25 FPS  Up to H.264 1280x720 30 FPS, H.264 720x480 30 FPS, JPEG 352x240 25 FPS     Up to H.264 1920x1080 30 FPS, H.264 720x480 30 FPS, JPEG 1280x720 25 FPS   Up toH.264 1920x1080 30 FPS, H.264 720x480 30 FPS, JPEG 720x480 25 FPS  Streaming 4-Streaming  Video streaming RTSP: RTP/HTTP, RTP/TCP, RTP/UDP   5Mbps to 128Kbps  Video bitrate Change frame rate and bitrate o n-the-fly   CBR/VBR/GOP supported   Base64 HTTP encryption  Security Multiple user access levels with password protection   10 user accounts available  Users 8 simultaneo us users  ePTZ & ROI Yes  OSD Overlay for date a nd time   Face detection   Tampering detection  Alar m/motio n Audio detection  Motion detection     Externa l digita l input a larm   Ima ge upload over FTP and e-mail by above  alar m signa ls  CPU, me mory Embe dde d SoC CPU at 528Mhz, 256 MB DDR, 256 MB flash me mory  IR cut re movable Auto , day , night, scheduling, da y & night mode ls only  Alar m input TTL input +3VDC to +5VDC, a larm input mo de ls only  Alar m o utput DC 24 1A, dry-contact (N.O.), a larm output mode ls only  Mainte nance Firmware update via HTTP, Firmware availa ble at we b site  Network interface 10Mbps/100Mbps, RJ-45  Two-wa y a udio G.711 64Kbits u-La w, audio mo de l only   OS: W indo ws 2000, W indo ws XP, W indo ws Vista, W indo ws 7  PC require ment Browser: W indo ws Internet Explorer 6.0 or above  CPU: Intel Pe ntium 4 1.8GHz or a bove     RAM: 1GB or above  Network protocols IP, TC P, UDP,  H TTP, SMTP, N TP, D DNS, U PnP,  FTP, ARP,  DHCP,  PPP oE, D NS,  RTSP, RTCP, Te lnet, Onvif    Mobil e  phone  &  P D A Support iPhone, iPa d, a nd Android  System integratio n ONVIF and HTTPAPI  AIM AIM HD 2.6 support  OS Embe dde d Linux 2.6 .32   
  
 
 36  
						

							 
  
 
  
 
  
 
  
 
  
 
  
 
  
 DISTRIBUTOR：   
 
  
 
 
 AirForce Dome Series