Acer Xs X13hg Users Guide

							21
EnglishImage
Projection
• Front-Desktop: The factory default setting.
• Front-Ceiling: When you select this function, the 
projector inverts the image for ceiling-mounted 
projection.
• Rear-Desktop: When you select this function, the 
projector reverses the image so that you can project 
behind a translucent screen.
• Rear-Ceiling: When you select this function, the 
projector reverses an d inverts the image at same time. 
You can project from behind a translucent screen with 
ceiling mounted projection.
Aspect  Ratio Use this function to choose your desired aspect ratio.
•Auto: Keeps the image with original width-height ratio 
and maximizes the image to 
fit native horizontal or 
vertical pixels.
•Full (S1310W/T220/XS-W10/S1310WHn/S1313W/
S1313WHn): The image will be displayed making full use 
of the horizontal and vertical pixels.
•4:3: The image will be scaled to fit the screen and 
displayed using a 4:3 ratio.
•16:9: The image will be scaled to fit the screen and 
displayed using a 16:9 ratio.
•L.Box (S1310W/T220/XS-W10/S1310WHn/S1313W/
S1313WHn): Keeps the original signal aspect ratio and 
zooms in by 1.333 times.
Keystone Adjusts image distortion caused by tilting projection (±40 
degrees).
Downloaded From projector-manual.com Acer Manuals 
						

							22
English
SharpnessAdjusts the sharpness of the image.•Press   to decrease the sharpness.
•Press   to increase the sharpness.
H. Position 
(Horizontal 
Position)
•Press   to move the image left.
•Press   to move the image right.
V. Position 
(Vertical 
Position)
•Press   to move the image down.
•Press   to move the image up.
FrequencyChanges the projector’s refresh rate to match the frequency 
of your computer’s graphics card. If you experience a vertical 
flickering bar in the projected image, use this function to 
correct it.
TrackingSynchronizes the signal timing of the display with the 
graphics card. If you experience an unstable or flickering 
image, use this function to correct it.
3D
•On
Select this item while using DLP 3D glasses, quad buffer 
(NVIDIA/ATI...) graphics card and HQFS format file or DVD 
with corresponding SW player.
•Off
Turns off the 3D mode.
3D Sync InvertIf you see a discrete or overlapping image while wearing DLP 
3D glasses, you may need to execute Invert to get best 
match of left/right image sequence to get the correct image 
(for DLP 3D).
3D Warning 
MessageChoose On to display the 3D warning message.
Downloaded From projector-manual.com Acer Manuals 
						

							23
English
Note: H. Position, V. Position, Frequency and Tracking functions 
are not supported under video mode.
Note: Sharpness function is not supported under computer mode.
Note: Supported 3D signal timings:
It needs correct settings on graphics card 3D application program for correct 
3D display.
The SW players, such as Stereoscopic Player and DDD TriDef Media Player 
can support 3D format files. You can download these players on the web 
page below.
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef-
3-D-Experience-4.0.2.html
Note: 3D Sync Invert is only available when 3D is enabled. Signal source type Supported timing
VGA 640 x 480@100Hz, 640 x 480@120Hz,
800 x 600@100Hz, 800 x 600@120Hz, 
1024 x 768@100Hz, 1024 x 768@120Hz HDMI (for S1210Hn/S1213Hn/
T212DT/XS-X13HG/S1310WHn/
S1313WHn)
Downloaded From projector-manual.com Acer Manuals 
						

							24
English
Setting
Menu LocationChooses the OSD menu locati on on the display screen.
HDMI Color 
Range 
(S1210Hn/
S1213Hn/
T212DT/XS-
X13HG/
S1310WHn/
S1313WHn) Adjusts the color range of the HDMI image data to prevent 
color display error.
•Auto: Automatically adjusts the color range by 
information from the player.
•Limited Range: Processes the input image as limited color 
range data.
•Full Range: Processes the input image as full color range 
data.
HDMI Scan Info 
(S1210Hn/
S1213Hn/
T212DT/XS-
X13HG/
S1310WHn/
S1313WHn) Adjusts the overscan ratio of
 the HDMI image on screen.
•Auto: Automatically adjusts the overscan ratio by 
information from the player.
•Underscan: Always no overscan on the HDMI image.
•Overscan: Always keep overscan on the HDMI image.
Closed Caption Selects a preferred closed captioning mode from CC1, CC2, 
CC3, CC4, (CC1 displays captions in the primary language in 
your area). Select Off to tu
rn off the captioning feature. 
This function is only available when a composite video or S-
Video input signal is selected and its system format is NTSC.
(S1110/T200/XS-S10/S1210/T210/
XS-X10/S1213/T212/XS-X13/
S1310W/T220/XS-W10/S1313W) (S1210Hn/S1213Hn/T212DT/XS-
X13HG/S1310WHn/S1313WHn)
Downloaded From projector-manual.com Acer Manuals 
						

							25
English
SecuritySecurity
This projector provides a usef
ul security function for the 
administrator to manage the projector.
Press   to change the Security setting. If the security 
function is enabled, your  must enter Administrator 
Password first before changing the security setting.
The factory default of Administrator Password is 
1234.
•Select On to enable the se curity function. You have to 
enter password depending on the Security Mode. 
Please refer to User Password section for details.
•If Off is selected, you can switch on the projector 
without password.
Timeout (Min.)
Once Security is set to On, you can set timeout function.
•Press   to select timeout duration.
•The range is from 10 to 990 minutes.
•When time is up, the projector will request you to enter 
the password again.
•The factory default setting of Timeout (Min.) is Off.
•Once the security function is enabled, the projector will 
request you to enter passwo rd when switching on the 
projector. Both User Password and Administrator 
Password can be accepted for this dialogue.
User Password
•Press   to set up or change User Password.
•Use the numerical keys on the remote control to set the 
password and press MENU to confirm.
•To delete the digits, Press  .
•Enter the password again  when you see Confirm 
Password displayed.
•The password should be 4~8 digits in length.
•If you select Request password only after plugging 
power cord, you are requested to input the password 
every time the power cord is plugged.
•If you select Always request password while projector 
turns on, you are requested  to input the password every 
time the projecto r is turned on.
Downloaded From projector-manual.com Acer Manuals 
						

							26
English
Administrator Password
You can enter Administrator Password when the Enter 
Administrator Password or Enter Password dialogue box 
displays.
•Press   to change Administrator Password.
•The factory default of Administrator Password is 
1234.
If you forget your administrator password, do the following 
to retrieve the administrator password:
•Enter the unique 6-digit Universal Password which is 
printed on the Security Card that came with your 
projector. This unique password will be accepted by the 
projector no matter what the administrator password is.
•If the Security Card is lost, please contact your local Acer 
service center.
VGA OUT 
(Standby)Selecting On enables the function. The projector can output 
a VGA signal when it is in standby mode and the VGA IN (or 
VGA IN 1) and VGA OUT sockets are correctly connected to the 
devices.
Enabling this function slightly increases the standby 
power consumption.
ResetPress   after choosing Yes to return the display 
parameters on all menus to the factory default settings.
Downloaded From projector-manual.com Acer Manuals 
						

							27
English
LAN Setting
(for S1210Hn/
S1213Hn/
T212DT/XS-
X13HG/
S1310WHn/
S1313WHn)To connect your projector to the network:
1 Take a RJ45 cable and connect one end to the LAN input 
jack of the projector and the other end to the RJ45 port.
2 Enter the LAN Setting menu. The Enter Administrator 
Password dialogue box is displayed.
3 Enter Administrator Password. The next level menu 
is displayed.
The factory default of Administrator Password is 
1234. You can change it in the Setting > Security > 
Administrator Password menu.
4 Select LAN in this menu and press   to select On.
5 Make sure DHCP is on, and press   to select Apply and 
press .
6 Re-enter the menu and note down the IP address 
displayed in the row of Projector IP Address.
If your are not in a DHCP environment, set DHCP to Off and 
contact your ITS administrator for information on Projector IP 
Address, Subnet Mask, Default Gateway, and DNS Server.
1 Press   to select Projector IP Address and press  .
2 Press   to move the cursor and press   to 
enter the digits.
3 When you finish, press MENU to save and exit the menu.
4 Repeat steps 1-3 to input addresses for Subnet Mask, 
Default Gateway, DNS server.
5 Press   to highlight Apply and press  .
To control the projector remotely:
1 Enter the Projector IP address in the address bar of the 
web browser on your computer.
2 The remote network operation page is displayed.You can 
control the projector by using this page. For details, see 
the notes following this table.
LAN Reset
(for S1210Hn/
S1213Hn/
T212DT/XS-
X13HG/
S1310WHn/
S1313WHn)Press   after choosing Yes to return all items on the Tools 
page to the default settings.
Downloaded From projector-manual.com Acer Manuals 
						

							28
English
Note: HDMI Color Range is only available when the input signal is HDMI.
About LAN Setting (for S1210H n/S1213Hn/T212DT/XS-X13HG/S1310WHn/
S1313WHn)
Note 1 :  An overview of the re mote network operation page
Note 2 :  An overview of the Tools page
Note 3:  The Info page shows the projector information and status.
To switch 
input signals, 
click your 
desired 
signal.These buttons 
function the 
same as those 
on the OSD 
menus, 
projector 
control panel, 
or remote 
control.
See Note 2 and 
Note 3.
You can 
enter the 
projector 
information.
You can 
adjust the 
LAN control 
settings.
You can set the 
user password/
administrator 
password to 
prevent 
unauthorized use 
of the remote 
network operation/
Tools page.
Downloaded From projector-manual.com Acer Manuals 
						

							29
EnglishManagement
ECO ModeChoose On to dim the projector lamp, which will also 
lower the power consumption, reduce noise, and extend 
the lamp life. Choose Off to return to the normal mode.
High AltitudeChoose On to turn on the High Altitude mode. When 
this function is turned on, the projector fans operate at full 
speed continuously to cool down the projector’s 
temperature.
Turn Off Mode
•Instant Off: Enables you to turn off the projector 
immediately without fan cooling process by pressing 
the power button twice.
•Instant Resume: Enables you to restart the projector 
immediately within 2 minutes after turning it off.
Auto Shutdown
(Minutes)The projector will automatically shut down while there is 
no signal input detected after the setting time.
Lamp Hour ElapseDisplays the lamp’s elapsed operating time (in hours).
Lamp RemindingChoose this function to show or hide warning message 
when the changing lamp message is displayed. The 
message will show up 30 hours before end of life.
Lamp Hour ResetPress   after choosing Yes to turn the lamp hour 
counter to 0 hours.
Downloaded From projector-manual.com Acer Manuals 
						

							30
English
Audio
Timer
Volume•Press   to decrease the volume.
•Press   to increase the volume.
Mute
•Choose On to turn mute on.
•Choose Off to turn mute off.
Timer LocationSets the location of the timer on the screen.
Timer Start (or 
Stop)Press   to start or stop the timer.
Timer Period 
(Minutes)Press   to adjust the timer period.
Timer VolumeSelect this function to adjust the notification volume 
when the timer function is enabled and time is up.
Timer Display
Press   to choose a timer display mode.
Downloaded From projector-manual.com Acer Manuals