Acer Xb270hab Users Guide

  Acer America Corporation  333 West San Carlos St., Suite 1500 San Jose, CA 95110, U. S. A.  Tel : 254-298-4000  Fax : 254-298-4147  www.acer.com 
 
  
 
 
 
 
 
 
Federal Communications Commission 
Declaration of Conformity    
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation....

 1 
Special notes on LCD monitors iii 
Information for your safety and comfort iii 
Safety instructions iii 
Cleaning your monitor iii 
Connecting/disconnecting the device iii 
Accessibility iv 
Safe listening iv 
Warnings iv 
Using electrical power iv 
Product servicing v 
Additional safety information vi 
IT equipment recycling information vi 
Disposal in structionsvii 
LCD pixel statement vii 
Tips and information for comfortable use viii 
Federal Communications Commission
Declaration of Conformity xi...

1
EnglishUnpacking
Please check that the following items are present when you unpack the box,  
and save the packing materials in case you need to ship or transport the 
monitor in the future.
LCD monitor   Quick start guide
AC power cord 
 
 (Option) DP cable 
 (Option)USB cable
 
 

2
A T T A C H I N G / R E M O V I N G   T H E   B A S EA T T A C H I N G / R E M O V I N G   T H E   B A S EA T T A C H I N G / R E M O V I N G   T H E   B A S EA T T A C H I N G / R E M O V I N G   T H E   B A SEA T T A C H I N G / R E M O V I N G   T H E   B A S E
Install: Align the base with the stand and push the base towards the top of the monitor, and then rotate the base clockwise. Tighten the screw clock-wise. 
Remove: Reverse the steps to remove the base.
English
 

3
S C R E E N   P O S I T I O N   A D J U S T M E N TS C R E E N   P O S I T I O N   A D J U S T M E N TS C R E E N   P O S I T I O N   A D J U S T M E N TS C R E E N   P O S I T I O N   A D J U S T M E N TS C R E E N   P O S I T I O N   A D J U S T M E N T
In oder to optimize the best viewing position, you can adjust the height/tilt/ swivel/pivot of the monitor.
• ••tliT tliTT i l tT i l tT i l t
Please see the illustration below for an example of the tilt range.
•••H e i g h t   A d j u s t m e n tH e...

4
• ••leviwS leviwSleviwS leviwSS w i v e l
With the built-in pedestal, you can swivel the monitor for the most 
comfortable viewing angle.
• ••M o n i t o r   P i v o tM o n i t o r   P i v o tM o n i t o r   P i v o tM o n i t o r   P i v o tM o n i t o r   P i v o t
Rotate clockwise until the monitor stops at 90°.
90o
150
English
Before rotating the display,lift it to the top position
and then push it back to the utmost degree. 
o
6060
 

5
EnglishConnecting the power cord
•Check first to make sure that the pow er cord you use is the correct type 
required for your area.
•The monitor has a universal power supply that allows operation in either 
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is 
required.
•Plug one end of the power cord to the AC inlet, and plug the other end 
into an AC outlet.
•For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
•For units using 220/240 V AC:
Use a...

6
English
Connector pin assignment 
PIN No. Description PIN No. Description
1
13
2
14
3
15
4
16
17
18
7
19
20
9
10
11
12 
5 
8 
6
Lane0(p)
GND
Lane0(n) 
Lane1(p)
GND
Lane1(n) 
Lane2(p)
GND
Lane3(n)
Lane3(p)
 GND
 Lane3(n)
Config1 
Config2
AUX_CH (n)
GND
AUX_CH (p)
Hot Plug Detect
DP Power_Return
DP Power
20-pin color display signal cable*
 

8
English
Standard timing table
1 
2
3 
UXGA   
UXGA 
UXGA  
1920x108060Hz  
 
1920x1080 120 Hz 
1920x1080 144 Hz 
 
 

9EnglishInstallation
To install the monitor on your host system, please follow the steps below:
Steps 
1 Connect the video cable
a Make sure both the monitor and computer are switched off. 
2 Connect the power cord
Connect the power cord to the monitor, then to a properly grounded AC  
outlet. 
Turn on the monitor and computer 
Turn on the monitor first, then the computer. This sequence is very important.
If the monitor does not function properly, please refer to the             troubleshooting section...