Acer X203wb Users Guide

							
Federal Communications CommissionDeclaration of Conformity
This device complies with Part 15 of the  FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, 
and (2) This device must accept any interference received, including 
interference that may cause undesired operation.
The following local manufacturer/importer  is responsible for this declaration:
M
odel number:

SKU
 number:

Name of responsible party: Acer America Corporation
Address of responsible party: 333 West San Carlos St. San Jose, CA 95110
USA
Contact person: Acer Representative
Tel: 1-254-298-4000
Fax: 1-254-298-4147
Product name:                             20W LCD Monitor   
X203H
X203H xx xx (x can be 0-9, A-Z or blank)
 
						

							
Special notes on LCD monitors iii
Information for your safety and comfort iiiSafety instructions iiiCleaning your monitor iii
Connecting/disconnecting the device iii
Accessibility iv
Safe listening iv
Warnings iv
Using electrical power iv
Product servicing v
Additional safety information vi
IT equipment recycling information vi
Disposal in structions vii
LCD pixel statement vii
Tips and information for comfortable use viii
Federal Communications Commission
Declaration of Conformity xi
Unpacking 1 Attaching/removing the base 2
Screen position adjustment 2
Connecting the power cord 3
Power saving 3
Display Data Channel (DDC) 3
Connector pin assignment 4
Standard timing table 6
Installation 7
User controls 8
How to adjust a setting 9 Acer eColor Management 10
User 11
Troubleshooting 13 VGA mode 13
DVI mode 14
 
						

							
EnglishUnpacking
Please check that the following items are present when you unpack the box, 
and save the packing materials in case you need to ship or transport the 
monitor in the future.
LCD monitor   User’s guide Quick start guide
D-sub cable   DVI cable (only dual-
input models) AC power cord
Audio Cable (Option) 
  
 
 
 
 
						

							
English
Attaching/removing the base
Screen position adjustment
Attaching:
Align the release button on the 
bottom of the monitor with the 
corresponding slots  on the bottom of 
the base.   Removing:
Press the release button as 
indicated, then pull in the direction 
of the arrow to remove the base.
To optimize the viewing position, you  can adjust the monitor tilt by using 
both of your hands to hold the ed ges of the monitor as shown below. 
The monitor can be adjusted to 15 degrees up or 5 degrees down. 
 
						

							
EnglishConnecting the power cord
•Check first to make sure that the pow er cord you use is the correct type 
required for your area.
•The monitor has a universal power supply that allows operation in either 
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is 
required.
•Plug one end of the power cord to the AC inlet, and plug the other end 
into an AC outlet.
•For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
•For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The 
cord set should have the appropriate  safety approvals for the country in 
which the equipment will be installed.
Power saving
The monitor will be switched to power saving mode by the control signal 
from the display controller, as indi cated by the amber-colored power LED.
The power saving mode will be kept until a control signal has been detected or 
the keyboard or mouse is activated. The recovery time from power saving 
mode back to on is around 3 seconds.
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, 
the monitor is able to plug-and-play. The DDC is a communication protocol 
through which the monito r automatically informs the host system about its 
capabilities; for example, supported resolutions and corresponding timing. The 
monitor supports th e DDC2B standard.
ModeLED light
On Blue
Power saving  Amber
 
						

							
English
Connector pin assignment
15-pin color display signal cable
PIN No.DescriptionPIN No.Description
1 Red 9 +5 V
2 Green 10 Logic ground
3 Blue 11 Monitor ground
4 Monitor ground 12 DDC-serial data
5 DDC-return 13 H-sync
6 R-ground 14 V-sync
7 G-ground 15 DDC-serial clock
8B-ground
15 6 10
11 15
 
						

							
English
24-pin color display signal cable
PIN No.DescriptionPIN No.Description
1 TMDS data 2- 13 NC
2 TMDS data 2+ 14 +5 V power
3 TMDS data 2/4 shield 15 GND (return for +5 V hsync.vsync)
4 NC 16 Hot-plug detection
5NC 17TMDS data 0-
6DDC clock 18TMDS data 0+
7 DDC data 19 TMDS data 0/5 shield
8NC 20NC
9 TMDS data 1- 21 NC
10 TMDS data 1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDS clock+
12 NC 24 DDC TMDS clock-
 
						

							
English
Standard timing table
Mode
1640 x 480 60Hz
2640 x 480                     72                    Hz
3640 x 480                     75                    Hz
4MAC640 x 480                     66.66               Hz
5VESA720x40070Hz
6SVGAHz
7                 SVGA 
19                 VESA
800 x 600
800 x 600
60
56
Hz
8SVGA 800 x 60072Hz
9SVGA 800 x 60075Hz
MAC832 x 62474.55Hz
XGA
XGA
XGA
1024 x 76860Hz
1024 x 76870Hz
1024 x 76875Hz
1152 x 87075Hz
VESA
VESA
1280 x 96060Hz
MAC
1152 x 86475Hz
SXGA
SXGA
1280 x 102460Hz
1280 x 1024
1280 x 720
75Hz
10
11
12
13
14
15
16
17
18
60Hz
20                 WXGA
21                 WXGA
22                 WXGA+
1280 x 80060Hz
60
60
Hz
Hz
1360x768
1600x900