Acer X183hbb Users Guide

							EN-1024-Pin Color Display Signal Cable
PINMeaningPINMeaning 1.TMDS Data2-13.TMDS Data3+
2.TMDS Data2+14.+5V Power
3. TMDS Data 2/4
Shield 15.GND(return for
+5V hsync.vsync)
4.TMDS Data4-16.Hot Plug Detect 5.TMDS Data4+17.TMDS Data0-
6.DDC Clock18.TMDS Data0+
7.DDC Data19. TMDS Data 0/5
Shield
8. Analogue Vertical
Sync 20.TMDS Data5-
9.TMDS Data1-21.TMDS Data5+
10.TMDS Data1+22.TMDS Clock Shield
11. TMDS Data 1/3
Shield 23.TMDS Clock+
12.TMDS Data3-24.DDC TMDS Clock-j·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s 
						

							E N-11
Standard Timing Table
ModeResolution
1
2
3
4
5
6VGA
SVGA                800*600@56Hz
                          800*600@60Hz
                          800*600@72Hz
                          800*600@75Hz
XGA                  1024*768@60Hz
                          1024*768@70Hz
                          1024*768@75Hz
                          1152*864@75Hz
                          1280*960@60Hz
SXGA                1280*1024@60Hz
                          1280*1024@75Hz
EGA                   720x400@70Hz
VGA                   640*[email protected]
SVGA                 832*624@75Hz
XGA                  1024*768@75Hz
                          1152*870@75Hz
VESA                1280x720@60Hz SXGA                1280*1024@70Hz 640*480@60Hz
640*480@72Hz
640*480@75Hz
WXGA               1280*800@60Hz
                          1366*768@60Hz
 
						

							EN-12INSTALLATION
T
o install the monitor to your host system, please follow the steps as given
below:
Steps
1.1-1Connect Video Cable a. Make sure both the monitor and computer are powered-OFF.
b. Connect the VGA video cable to the computer.
1-2Digital Cable (Only Dual-Input Model) a. Make sure both the monitor and computer are powered-OFF.
b. Connect one end of the 24-pin DVI cable to the back of the
monitor and connect the other end to the computer’s port.
Connect the power cord to the monitor, then to a properly grounded AC
This sequence is very important.
troubleshooting section to diagnose the problem.
3
3
Power-ON the monitor first, then power-ON the computer. outlet.
3.Power-ON Monitor and Computer
4.If the monitor still does not function properly, please refer to the 2.Connect power cord
j·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s 
						

							EN-13USER CONTROLS
Front
 Panel Controls
1.Power Switch:
To turn ON or OFF the power.
2.Power LED:
Lights up to indicate the power is turned ON.
3.Empowering / Exit:
1) When OSD menu is in active status, this button will act as EXIT-KEY(EXIT
OSD menu).
2) When OSD menu is in off status, press this button to select scenario
mode.
4.Auto Adjust button / Exit:
1)When OSD menu is in active status, this button will act as EXIT-KEY (EXIT
OSD menu).
2)When OSD menu is in off status, press this button for 2 seconds to
activate the AutoAdjustment function.The Auto Adjustment function is
used to set the HPos, VPos, Clock and Focus.
5.< / >
Press < or  > to select the desired function.Press < or  > to change the
settings of the current function.
6.MENU / ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function whenOSD is ON or Exit OSD menu when in Volume Adjust OSD
status. 1
345 6 2
5 
						

							EN-14
1.Acer eColor Management
If selected to “Acer eColor Management “ item, will appear the
Acer eColor” OSDHOW TO ADJUST A SETTING
1
 .Press the MENU-button  to activate the OSD window.
2.Press < or  > to select the desired function.
3.Press the MENU-button  to select the function that you want to adjust.
4.Press < or  > to change the settings of the current function.
5.To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-4.
· P/X Series OSD behave
When user press “MENU” button on front bezel
· OSD and”  Key “ locations
Value LinePerformance Line and
Gamer Line
Value Line
w/speaker
Office Line 1
2j·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s 
						

							EN-15·
Acer eColor Management  OSD
Acer eColor Management Step 1: Press “  Key “ to open the Acer eColor Management OSD and
access the scenario modes
Step 2:Press “” to select the mode
Step 3:Press “   Key “ to confirm the mode and run Auto Adjust
Automatic Adjustment Step 1:Press “ Auto Key “to initial scenario mode
Step 2:Press “ Auto Key “ again to perform an Auto Adjust ·
Operation instructionsj·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s 
						

							EN-16
I. Only Analog Input Model
2.USER
If selected to “USER” item, will appear the Standard OSD
·
Features and Benefitsj·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s 
						

							EN-17·
ADJUSTING THE PICTURE
The descriptions for function control LEDS II. Only Dual Input ModelMain
Menu icon Sub
Menu icon Sub
Menu item Description
Contrast Adjusts the contrast between the
foreground andbackground of the
screen image.
Brightness Adjusts the background brightness of
the screenimage.
ACM ACM (Adaptive Contrast Management):
ACM ON/OFF Switch, default  is "OFF"
Focus Adjusts picture Focus.(available in
Analog mode only)
Clock Adjusts picture Clock.(available in
Analog mode only)j·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s 
						

							EN-18Main
Menu Icon Sub Menu
Icon Sub Menu
Item Description
H. Position Adjust the horizontal position.
(available in Analog  mode only)
V. Position Adjust the vertical position.
(available in Analog  mode only)
N/AWarm Set the color temperature to warm
white.
N/ACool Set the color temperature to cool
white.
User /Red
Adjusts Red/Green/Blue intensity.
User /Green
User /Blue
N/AEnglish
Multi-language selection.
N/A
N/ADeutsch
N/AFrancais
N/AEspanol
N/AItaliano
N/A
N/A
N/ASuomi
EMEA version OSD only
N/ANederlands
N/APyccknnj·w">·EV(VS)r·JS4E"uE>4·"“t·rDQ·JS4E"uE>s