Acer X1230ps Users Guide

21
English
Note: H. Position, V. Position, Frequency and Tracking functions 
are not supported under video mode.
Note: Sharpness function is not supported under computer mode.
Note:
The 3D function is supported by VGA source only. Please see the timing 
table for detailed 3D timings.
While using NVIDIA 3D Vision, please download and install the latest 
NVIDIA 3D Vision driver from NVIDIA web site for your graphics card to 
support this projector.
H. Position 
(Horizontal 
Position)Press   to move the...

22
English
It needs correct settings on graphics card 3D application program for correct 
3D display.
The SW players, such as Stereoscopic Player and DDD TriDef Media Player 
can support 3D format files. You can download these players on the web 
page below.
- NVIDIA Stereoscopic 3D Video Player: http://www.nvidia.com/object/
3D_Drivers_Downloads.html
-Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
-DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef-3-...

23
English
Closed CaptionSelects a preferred closed captioning mode from CC1, CC2, 
CC3, CC4, (CC1 displays captions in the primary language in 
your area). Select Off to turn off the captioning feature. 
This function is only available when a composite video or S-
Video input signal is selected and its system format is NTSC.
Set your screen aspect ratio to 4:3. The function is not 
available when the aspect ratio is 16:9 or 16:9 format 
detected under Auto mode.
SecuritySecurity
This projector provides...

24
English
User Password
Press   to set up or change User Password.
Use the numerical keys on the remote control to set the 
password and press MENU to confirm.
To delete the digits, Press  .
Enter the password again when you see Confirm 
Password displayed.
The password should be 4~8 digits in length.
If you select Request password only after plugging 
power cord, you are requested to input the password 
every time the power cord is plugged.
If you select Always request password while projector...

25
EnglishManagement
ECO ModeChoose On to dim the projector lamp, which will also 
lower the power consumption, reduce noise, and extend 
the lamp life. Choose Off to return to the normal mode.
High AltitudeChoose On to turn on the High Altitude mode. When 
this function is turned on, the projector fans operate at full 
speed continuously to cool down the projector’s 
temperature.
Auto Shutdown
(Minutes)The projector will automatically shut down while there is 
no signal input detected after the setting...

26
English
Audio
Timer
VolumePress   to decrease the volume.
Press   to increase the volume.
Mute
Choose On to turn mute on.
Choose Off to turn mute off.
Timer LocationSets the location of the timer on the screen.
Timer Start (or 
Stop)Press   to start or stop the timer.
Timer Period 
(Minutes)Press   to adjust the timer period.
(X1130PA/X1130PS/X1230P/
X1230PA/X1230PK/X1230PS/
X1237)
Downloaded From projector-manual.com Acer Manuals 

27
English
Language
Timer VolumeSelect this function to adjust the notification volume 
when the timer function is enabled and time is up.
Timer Display
Press   to choose a timer display mode.
Language
Sets a language for the OSD menus. Use   to 
select your preferred language.
Press   to confirm the selection.
Downloaded From projector-manual.com Acer Manuals 

28
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following 
troubleshooting guide. If the problem persists, please contact your local reseller 
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears 
onscreen•Make sure all the cables are correctly connected as 
described in the Getting Started section.
•Ensure none of the connector pins are bent or 
broken.
•Check if the projection lamp has been securely 
installed....

29
English
3 Partial, scrolling 
or incorrectly 
displayed image
(For notebooks)•Press RESYNC on the control panel or remote 
control.
•For an incorrectly displayed image:•Follow the steps for item 2 (above) to adjust 
the resolution of your computer.
•Press the toggle output settings. Example: 
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], 
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP 
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•If you experience difficulty changing resolutions or 
your monitor freezes, restart...

30
English
Problems with the Projector
8 Image is stretched 
when displaying a 
widescreen 
DVD titleWhen you play a DVD encoded in anamorphic or 16:9 
aspect ratio you may need to adjust the following 
settings:
•If you play a 4:3 format DVD title, please change the 
format to 4:3 with the projector OSD.
•If the image is still stretched, you will also need to 
adjust the aspect ratio. Set up the display format to 
16:9 (wide) aspect ratio on your DVD player.
9 Image is too small 
or too large
•Adjust...