Acer V243wb Users Guide

 
  Acer America Corporation  333 West San Carlos St., San Jose 
  CA 95110, U. S. A. 
  Tel : 254-298-4000  Fax : 254-298-4147   www.acer.com 
 
 
 
 
 
 
   
Federal Communications Commission 
Declaration of Conformity 
 
 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) this device ma y not cause harmful interference, and (2) 
this device must accept any interferen ce received, including interference that may 
cause undesired operation....

1
Special notes on LCD monitorsiii
Information for your safety and comfort iii
Safety instructions iii
Cleaning your monitor iii
Connecting/disconnecting the device iii
Accessibility iv
Safe listening iv
Warnings iv
Using electrical power iv
Product servicing v
Additional safety information vi
IT equipment recycling information vi
Disposal in structions vii
LCD pixel statement vii
Tips and information for comfortable use viii
Federal Communications Commission
Declaration of Conformity xi
Unpacking 1...

1
EnglishUnpacking
Please check that the following items are present when you unpack the box, 
and save the packing materials in case you need to ship or transport the 
monitor in the future.
LCD monitor   U
 ser’s guideQuick start guide
D-s
ub cable (Option)  DVI cable (Option) AC power cord
Audio Cable (Option) 
    
 
 
 (Option) 
DP cable 
LCD Monitor
 

2
English
Attaching/removing the base
Screen position adjustment
Attaching:
Align the release button on the 
bottom of the monitor with the 
corresponding slots  on the bottom of 
the base.   Removing:
Press the release button as 
indicated, then pull in the direction 
of the arrow to remove the base.
To optimize the viewing position, you  can adjust the monitor tilt by using 
bo
 th of your hands to hold the edges of the monitor as shown below. 
The monitor can be adjusted to 15 degrees up or 5 degrees...

3
EnglishConnecting the power cord
•Check first to make sure that the pow er cord you use is the correct type 
required for your area.
•The monitor has a universal power supply that allows operation in either 
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is 
required.
•Plug one end of the power cord to the AC inlet, and plug the other end 
into an AC outlet.
•For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
•For units using 220/240 V AC:
Use a...

4
English
Connector pin assignment
15-pin color display signal cable
PIN No.DescriptionPIN No.Description
1 Red 9 +5 V
2 Green 10 Logic ground
3 Blue 11 Monitor ground
4 Monitor ground 12 DDC-serial data
5 DDC-return 13 H-sync
6 R-ground 14 V-sync
7 G-ground 15 DDC-serial clock
8B-ground
15 6 10
11 15
 

5English
24-pin color display signal cable*
PIN No.DescriptionPIN No.Description
1 TMDS data 2- 13 NC
2 TMDS data 2+ 14 +5 V power
3 TMDS data 2/4 shield 15 GND (return for +5 V hsync.vsync)
4 NC 16 Hot-plug detection
5NC 17TMDS data 0-
6DDC clock 18TMDS data 0+
7 DDC data 19 TMDS data 0/5 shield
8NC 20NC
9 TMDS data 1- 21 NC
10 TMDS data 1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDS clock+
12 NC 24 DDC TMDS clock-
PIN No.DescriptionPIN No.Description
1
13
2
14
3
15
4
16
17
18
7
19
20
9
10 11...

6
English
ModeResolution
Standard timing table
1Dos 720 x 400 70Hz
2 VGA 640 x 480 60Hz
3 VGA 640 x 480 67Hz
4   
800 x 60056Hz
5
800 x 60060
Hz
6
XGA 1024 x 768 60Hz
7
  XGA 1024 x 768
70
Hz
8
1280 x 102460Hz
10 
1152x 86475
Hz
11 
12 
               WXGA 1280x 800
60Hz
VESA
9
VGA 640 x 480 72Hz
VGA 6
40 x 480
75Hz
SVGA 800

 x 600 72
Hz
SVGA 800 x 600 75Hz
XGA 1024 x 768 75Hz
13  MAC
832 x 624 74.55Hz
14  
MAC 1152
 x 870 75Hz
15  
16
1280x 96060Hz
VESA
17
SVGA 1280 x 1024 75Hz
18
1280x 720
60Hz
VESA...

7EnglishInstallation
To install the monitor on your host system, please follow the steps below:
Steps 
1 Connect the video cable
a Make sure both the monitor and computer are switched off.
b Connect the VGA video cable to the computer. 
c Connect the digital cable (only for dual-input models).
(1) Make sure both the monitor and computer are switched off.
(2) Connect one end of the 24-pin DVI cable to the back of the monitor and the other end to the computers port.
2 Connect the power cord Connect the...

8
English
User controls
Front panel controls
1     Power LED: Lights up to indicate the power is turned on. 
2     Power Switch : Turn the power on or off. 
3.4   < / >  : Press < or > to navigate to the desired function, press Enter to   
            select the function. Press < or > to change the settings of the   
           current function. 
5     Menu/Enter : Activate the OSD menu when the OSD is off or activate 
                  / deactivate the adjustment function when the OSD is on. 
6     Auto...