Acer V233hlbd Users Guide

xi
Federal Communications CommissionDeclaration of Conformity
This device complies with Part 15 of the  FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, 
and (2) This device must accept any interference received, including 
interference that may cause undesired operation.
The following local manufacturer/importer  is responsible for this declaration:
Product name:
23 LCD Monitor

Model number:
V233H

SKU number:
V233Hxxxx
Name of...

1
Special notes on LCD monitors iii
Information for your safety and comfort iiiSafety instructions iiiCleaning your monitor iii
Connecting/disconnecting the device iii
Accessibility iv
Safe listening iv
Warnings iv
Using electrical power iv
Product servicing v
Additional safety information vi
IT equipment recycling information vi
Disposal in structions vii
LCD pixel statement vii
Tips and information for comfortable use viii
Federal Communications Commission
Declaration of Conformity xi
Unpacking 1...

1
EnglishUnpacking
Please check that the following items are present when you unpack the box, 
and save the packing materials in case you need to ship or transport the 
monitor in the future.
LCD monitor   User’s guide Quick start guide
D-sub cable   DVI cable (only dual-
input models) AC power cord
Audio Cable (Option) 
  
 
 
 
 

2
English
Attaching/removing the base
Screen position adjustment
Attaching:
Align the release button on the bottom of the monitor with the 
corresponding slots on the bottom of 
the base.  
Removing:
Press the release button as indicated, then pull in the direction 
of the arrow to remove the base.
To optimize the viewing position, you can adjust the monitor tilt by using both of your hands to hold the edges of the monitor as shown below. 
The monitor can be adjusted to 15 degrees up or 5 degrees down. 
 

3
EnglishConnecting the power cord
•Check first to make sure that the pow er cord you use is the correct type 
required for your area.
•The monitor has a universal power supply that allows operation in either 
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is 
required.
•Plug one end of the power cord to the AC inlet, and plug the other end 
into an AC outlet.
•For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
•For units using 220/240 V AC:
Use a...

4
English
Connector pin assignment
15-pin color display signal cable
PIN No.DescriptionPIN No.Description
1 Red 9 +5 V
2 Green 10 Logic ground
3 Blue 11 Monitor ground
4 Monitor ground 12 DDC-serial data
5 DDC-return 13 H-sync
6 R-ground 14 V-sync
7 G-ground 15 DDC-serial clock
8B-ground
15 6 10
11 15
 

5
English
24-pin color display signal cable
PIN No.DescriptionPIN No.Description
1 TMDS data 2- 13 NC
2 TMDS data 2+ 14 +5 V power
3 TMDS data 2/4 shield 15 GND (return for +5 V hsync.vsync)
4 NC 16 Hot-plug detection
5NC 17TMDS data 0-
6DDC clock 18TMDS data 0+
7 DDC data 19 TMDS data 0/5 shield
8NC 20NC
9 TMDS data 1- 21 NC
10 TMDS data 1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDS clock+
12 NC 24 DDC TMDS clock-
 

6
English
ModeResolution
Standard timing table
1Dos 720 x 400 70Hz
2 VGA 640 x 480 60Hz
3 VGA 640 x 480 67Hz
4            SVGA 800 x 600 56Hz
5  SVGA 800 x 600 60
Hz
6
XGA

1024 x 768
60
 Hz
7
  XGA

1024 x 768
70
 Hz
8
SXGA

1280 x 1024
60Hz
9 NA 1440 x 90060 Hz
10 NA1152x 86475 Hz
11 
UXGA
 1920 x 1080
60Hz
12 ACER 1280x 80060Hz
 

7
EnglishInstallation
To install the monitor on your host system, please follow the steps below:
Steps 
1 Connect the video cable
a Make sure both the monitor and computer are switched off. 
b Connect the VGA video cable to the computer.  
c Connect the digital cable (only for dual-input models).
(1) Make sure both the monitor and computer are switched off. 
(2) Connect one end of the 24-pin DVI cable to the back of the 
monitor and the other end to the computers port.
2 Connect the power cord
Connect...

8
English
User controls
Front panel controls
1     Power LED: Lights up to indicate the power is turned on. 
2     Power Switch : Turn the power on or off. 
3.4   < / >  : Press < or > to navigate to the desired function, press Enter to   
            select the function. Press < or > to change the settings of the   
           current function. 
5     Menu/Enter : Activate the OSD menu when the OSD is off or activate 
                  / deactivate the adjustment function when the OSD is on. 
6    Auto...