Acer Travelmate 8571 Service Guide

Chapter 233
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The...

34Chapter 2
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following 
message.
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay. 

Chapter 235
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding 
ChangesExit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS. 

36Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
‰New versions of system programs
‰New features or options
‰Restore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please...

Chapter 337
This chapter contains step-by-step procedures on how to disassemble the notebook computer TravelMate 
8571/8531 for maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
‰Wrist grounding strap and conductive mat for preventing electrostatic discharge
‰Small Philips screw driver
‰Philips screwdriver
‰Plastic flat head screw driver
‰Tw e e z e r s
NOTE: The screws for the different components vary in size. During the disassembly process, group the 
screws...

38Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system.
3.Remove the battery pack. 

Chapter 339
Disassembly Procedure Flowchard
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frames 
in that order.
Main unit disassembly flow chart
LCM module disassembly flow chart 

40Chapter 3
Removing the Battery Pack
1.Release the battery lock.
2.Slide the battery latch then remove the battery.
NOTE: Battery has been highlighted with the yellow circle as above image shows. Please detach the battery 
and follow local regulations for disposal. 

Chapter 341
Removing the HDD and RAM
1.Remove two screws on the HDD cover and remove HDD. 
  
Ty p e N u m b e r
M2*5(4.5D*0.8T) 2 

42Chapter 3
2.Remove the screw on RAM cover and remove RAM.
3.Remove RTC battery.
NOTE: RTC battery has been highlighted with the yellow circle as above image shows. Please detach the 
RTC battery and follow local regulations for disposal.  
Ty p e N u m b e r
M2*5(4.5D*0.8T) 1