Acer Travelmate 7320 Service Guide

							Chapter 361
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you 
on the components that need to be removed during servicing. For example, if you want to remove the main 
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Screw List
ScrewPart No.
A M2.5 x L6 86.00E33.736
B M2 x L4 86.00A02.140
C M2 x L4 86.9A552.4R0
G M3 x L4 86.9A544.4R0
K M3 x L3 86.00E94.723
EXTERNAL MODULE DISASSEMBLY
WLAN
BOARDTURN OFF POWER
AND PERIPHERALS
UNPLUG POWER
CABLES
Cx2
LOWER
COVER Bx9
DIMM
MODULES
OPTICAL DISK
DRIVE MODULEAx1
OPTICAL DISK
DRIVEKx2OPTICAL
LOCKER
BRACKETHDD
MODULE
HARD DISK
BRACKET
HARD DISK
DRIVE
Gx4
2nd HDD
COVER
HARD DISK
BRACKET Bx2
SG_Tangiz.book  Page 61  Tuesday, July 10, 2007  11:01 AM 
						

							62Chapter 3
Removing the Battery Pack
1.Turn base unit over. 
2.Slide the battery lock/unlock latch to the unlock position. 
3.Slide and hold the battery release latch to the release position, then remove the battery from the main 
unit. 
SG_Tangiz.book  Page 62  Tuesday, July 10, 2007  11:01 AM 
						

							Chapter 363
Removing the SD dummy card
1.Push the SD dummy card all the way in to eject it (1, 2).
2.Pull it out from the slot (2). 
Removing the PC and ExpressCard dummy cards
1.Press the eject button to pop out the button.
SG_Tangiz.book  Page 63  Tuesday, July 10, 2007  11:01 AM 
						

							64Chapter 3
2.Press it again (1) to pop out the PC dummy card (2). Remove the PC dummy card from the slot.
3.Push the ExpressCard dummy card all the way in to eject it. 
4.Pull it out from the slot.
Removing the Lower Cover
1.See “Removing the Battery Pack” on page 62.
SG_Tangiz.book  Page 64  Tuesday, July 10, 2007  11:01 AM 
						

							Chapter 365
2.See “Removing the SD dummy card” on page 63.
3.See “Removing the PC and ExpressCard dummy cards” on page 63.
4.Loosen the nine screws (B) on the lower cover.   
5.Use a plastic screw driver to carefully pry open the lower cover. 
6.Remove the lower cover from the lower case. 
Removing the Secondary HDD Cover
1.See “Removing the Battery Pack” on page 62.
2.See “Removing the SD dummy card” on page 63.
3.See “Removing the PC and ExpressCard dummy cards” on page 63.
4.See “Removing the Lower Cover” on page 64.
StepSize (Quantity)ColorTo r q u e
1~9 M2 x L4 (9) Black 1.6 kgf-cm
SG_Tangiz.book  Page 65  Tuesday, July 10, 2007  11:01 AM 
						

							66Chapter 3
5.Loosen the two screws (B) from the secondary HDD cover. 
6.Use a plastic screw driver to pry open the secondary HDD cover.
7.Remove the secondary HDD cover from the lower case.
Removing the Secondary HDD Bracket and Connector
1.See “Removing the Battery Pack” on page 62.
2.See “Removing the Secondary HDD Cover” on page 65.
StepSize (Quantity)ColorTo r q u e
1~2 M2 x L4 (2) Black 1.6 kgf-cm
SG_Tangiz.book  Page 66  Tuesday, July 10, 2007  11:01 AM 
						

							Chapter 367
3.Remove the HDD Bracket from the slot.
4.Disconnect the SATA power connector. 
5.Disconnect the SATA connector.
6.Remove the aluminium tape together with the connector.
SG_Tangiz.book  Page 67  Tuesday, July 10, 2007  11:01 AM 
						

							68Chapter 3
Removing the DIMM 
1.See “Removing the Battery Pack” on page 62.
2.See “Removing the SD dummy card” on page 63.
3.See “Removing the PC and ExpressCard dummy cards” on page 63.
4.See “Removing the Lower Cover” on page 64.
5.See “Removing the Secondary HDD Cover” on page 65.
6.Push out the latches on both sides of the DIMM socket to release the DIMM. 
7.Remove the DIMM module. 
Removing the WLAN Board Modules
1.See “Removing the Battery Pack” on page 62.
2.See “Removing the SD dummy card” on page 63.
3.See “Removing the PC and ExpressCard dummy cards” on page 63.
4.See “Removing the Lower Cover” on page 64.
5.Remove the tape holding the gray antenna. 
SG_Tangiz.book  Page 68  Tuesday, July 10, 2007  11:01 AM 
						

							Chapter 369
6.Disconnect the antenna cables from the WLAN board. 
7.Move the antenna away from the WLAN board and remove the two screws (C) on the WLAN board to 
release the WLAN board.   
8.Detach the WLAN board from the WLAN socket. 
NOTE:  When attaching the antenna back to the WLAN board, make sure the cable are arranged properly. 
Removing the Hard Disk Drive Module 
1.See “Removing the Battery Pack” on page 62.
2.See “Removing the SD dummy card” on page 63.
3.See “Removing the PC and ExpressCard dummy cards” on page 63.
4.See “Removing the Lower Cover” on page 64.
StepSize (Quantity)ColorTo r q u e
1~2 M2 x L4 (2) Silver 1.6 kgf-cm
SG_Tangiz.book  Page 69  Tuesday, July 10, 2007  11:01 AM 
						

							70Chapter 3
5.Disconnect the hard disk module from the connector by pulling on the mylar tab on the hard disk module.
6.Remove the hard disk module. 
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 
7.Remove the four screws (G) as shown. 
8.Remove the hard disk drive from the bracket.
Removing the Optical Drive Module
1.See “Removing the Battery Pack” on page 62.
StepSize (Quantity)ColorTo r q u e
1~4 M3 x L4 (4) Silver 1.8 kgf-cm
SG_Tangiz.book  Page 70  Tuesday, July 10, 2007  11:01 AM