Acer Travelmate 720 Service Guide

Chapter 2 53
Exit
When you select the Exit menu or press Esc
 from any screen, the Exit 
options screen displays.
The table describes the parameters in this screen. 
Note: 
If you wish to keep any changes you make to parameters, select 
Exit Saving Changes or Save Changes.
ParameterDescription
Exit Discarding 
ChangesDiscards any changes made, exits the Setup utility and 
reboots.
Exit Saving 
ChangesSaves any changes made, exits the Setup utility and 
reboots.
Load Setup 
DefaultsResets all parameters...

54 System Utilities
720.book  Page 54  Saturday, March 6, 1999  10:00 AM 

Chapter 3 55
This chapter contains procedures on how to disassemble the notebook 
computer for maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
TWrist grounding strap and conductive mat for preventing electrostatic 
discharge
TTwo flat-bladed screwdrivers
TPhillips screwdriver
THexagonal screwdriver
TTw e e z e r s
TPlastic stick
TSpecial tool for CPU
The flowchart on the following page gives a clearer and more graphic 
representation of the entire disassembly...

56 Removal and Replacement
SCREW  LIST
A : M 2  x 4 L     (B /Z N ) (N ylo k)
E : M 2  x 4 L     (N I)
F: M 2.5 x 13.5L (B/ZN) (Nylok)
G :M 2 .5  x 8 L  (B /Z N ) (N ylo k)
H : M 2 .5  x 6 L  (B /Z N ) (N ylo k)
I:  M 2 .5  x 1 8 L  (B /Z N )
J: M 2 x 4L (Round washer head)
L: M2 x 18L (NI)
N : M 2 .5  x 1 5 L  (B /Z N ) x1
O: M3 x 4L
P:M2 x 2.5L (NI)
Q :M 2 x 8 L (N I)
HDD
M oduleHDD and
HDD ShieldHDD
Connector
BoardHDD
Hinge CapL x 2
F x 2
G x 2
LCD ModuleLCD Bezel
LED Board
LCD and
In ve rte r
Board...

Chapter 3 57
External Module Replacement
Reassembling the Modem Board
1.  Connect the modem cable to the system board.
2.  Insert the modem board back into its socket.
3.  Put on the modem board cover.
4.  Secure the modem board cover with its original screw.
Installing Memory
1.  Insert the DIMM module into its socket.
2.  Put on the DIMM cover. 
720.book  Page 57  Saturday, March 6, 1999  10:00 AM 

58 Removal and Replacement
3. Secure the DIMM cover with its original screw.
Disassembling the CD-ROM Drive
1.  Push the CD-ROM drive locker forward and carefully pull out the CD-ROM 
module.
2.  To disassemble the CD-ROM module, remove the 2 screws from both 
sides of the CD-ROM module and the screw on the CD-ROM chassis.
3.  Remove the CD-ROM drive from the CD-ROM chassis.
720.book  Page 58  Saturday, March 6, 1999  10:00 AM 

Chapter 3 59
4.  Disconnect the cable of the CD-ROM drive.
Removing the Hard Disk Drive
1.  Use a flat-bladed screwdriver to remove the screw of the hard disk drive.
2.  Carefully, pull out the hard disk drive to remove it.
Disassembling the Hard Disk Drive
1.  To disassemble the hard disk drive, remove the 2 screws on both sides of 
the hard disk drive.
2.  Separate the hard disk drive from its bezel.
720.book  Page 59  Saturday, March 6, 1999  10:00 AM 

60 Removal and Replacement
3.  Remove the hard disk drive from it’s shield plate.
4.  Disconnect the hard disk cable from the hard disk drive.
5.  To reconnect the hard disk cable, be sure that the 1st pin is aligned up as 
indicated.
Removing and Replacing the Battery Pack
1.  To remove the battery pack, press the battery compartment cover latch 
and slide the cover out. 
720.book  Page 60  Saturday, March 6, 1999  10:00 AM 

Chapter 3 61
2.  Pull out the battery pack.
3.  Reinsert the battery pack by sliding it back in.
4.  Slide the battery compartment cover into its place.
720.book  Page 61  Saturday, March 6, 1999  10:00 AM 

62 Removal and Replacement
Removing the Keyboard
1.  Slide out the hinge covers on both sides of the notebook.
2.  To remove the middle cover, use a flatbladed screwdriver to release the 
latches as shown.
3.  Lift the middle cover away
.
720.book  Page 62  Saturday, March 6, 1999  10:00 AM