Home > Acer > Notebook > Acer Travelmate 6493 Service Guide

Acer Travelmate 6493 Service Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Acer Travelmate 6493 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Chapter 121
    LAN Interface
    ItemSpecification
    LAN Chipset INTEL 82567LM GIGA LAN
    Features
    •IEEE 802.3ab conformance
    •Line length > 140 m 
    •Operates with worst-case cable
    •Supports carrier extension (half duplex)
    •Wake-on-LAN and remote wake-up support
    •Auto-negotiation with support for next page
    •Smart speed operation, for automatic speed reduction on 
    faulty cable plants
    •Automatic MDI crossover capable
    •PMA loopback capable (No echo cancel)
    •Advanced power management:
    •Low power link up - differentiate between D0a/non-
    D0a
    •Auto Connect Battery Saver - link disconnect.
    •Advanced cable diagnostics:
    •TDR
    •Channel frequency response
    •Extended configuration load sequence
    •Automatic resolution of FDX/HDX mismatch in:
    •10/100 forced configurations        
    •Dual interconnect between MAC and PHY:
    •LCI for 10/100 Mb/s operation control traffic
    •GLCI for 1000 Mb/s operation
    •Three LED outputs
    Power Multiple voltage regulation modes:
    •External voltage regulation
    •Fully integrated linear regulator (nominal 1.0V 
    programmable)
    •Discrete linear voltage regulator (nominal 1.8V 
    programmable)
    •Reduced power consumption during normal operation 
    and power down modes
    •Support GLCI K0s reduced power mode in 10/100/1000 
    full duplex operation 
    						
    							22Chapter 1
    Card BUS/Reader
    ItemSpecification
    Controller OZ711MZ
    Features
    •Single-Slot PC Card (Card Bus) Controller
    •PC Card Standard Release 8.1 Compliant
    •Compliant with PCL Local Bus Specification Version 3.0
    •Integrate Flash Media and SDIO Readers
    •SD Host Interface Specification V2.0 with DMA
    •Complies to MutilMediaCard Version 4.1
    •Support SD/SDHC up to 50MHz Clock Rate
    •Support SD-CPRM and Panasonic SD-Jukebox
    •Supports MMCPlus Connectivity at 50MHz
    •Support Xd-Picture Card Type-M and Type-H
    •SDIO Version 1.10 Compliant with High-Speed Mode
    •Support Memory Stick PRO-HG up to 60MHz Clock
    •Support Memory Stick and Memory Stick PRO
    •Integrate Smart Card Reader
    •Smart Card available in NT package option
    •Provides an EMV L1 Certifiable Solution
    •O2 WDM Software Driver with CT-API Support
    •Power Interface Support Class A,AB,ABC Card
    •Fully Conform to ISO 7816-1/2/3/4 and PC/SC
    •Support T=0 and T=1 Smart Card Transmissions
    Power Management
    •Advanced Configuration and Power Interface Rev2.0 
    •PCI Bus Power Management Rev 1.1 Compliant 
    •Provide PCI Clock Control Protocol via CLKRUN# 
    •Support System Wake-UP via PME# Events 
    •OZ-711MZ0 - 128-pin LQFP (Lead Free) 
    						
    							Chapter 123
    Serial BUS Type TI-TSB43AB22A 1394 Function
    Features
    •Fully compliant with provisions of IEEE Std 1394-1995 for a high-
    performance serial bus1 and IEEE Std 1394a-2000
    •Fully interoperable with FireWire and i.LINK implementations of IEEE Std 
    1394
    •Compliant with Intel Mobile Power Guideline 2000
    •Full IEEE Std 1394a-2000 support includes: connection debounce, 
    arbitrated short reset, multispeed concatenation, arbitration acceleration, 
    fly-by concatenation, and port disable/suspend/resume
    •Power-down features to conserve energy in battery-powered 
    applications include: automatic device power down during suspend, PCI 
    power management for link-layer, and inactive ports powered down 
    •Ultralow-power sleep mode
    •Two IEEE Std 1394a-2000 fully compliant cable ports at 100M bits/s, 
    200M bits/s, and 400M bits/s
    •Cable power presence monitoring
    •Separate cable bias (TPBIAS) for each port
    •1.8-V core logic with universal PCI interfaces compatible with 3.3-V and 
    5-V PCI signaling environments
    •Physical write posting of up to three outstanding transactions
    •PCI burst transfers and deep FIFOs to tolerate large host latency 
    •PCI_CLKRUN protocol
    •External cycle timer control for customized synchronization
    •Extended resume signaling for compatibility with legacy DV components
    •PHY-Link logic performs system initialization and arbitration functions
    •PHY-Link encode and decode functions included for data-strobe bit level 
    encoding
    •PHY-Link incoming data resynchronized to local clock
    •Low-cost 24.576-MHz crystal provides transmit and receive data at 
    100M bits/s, 200M bits/s, and 400M bits/s
    • Node power class information signaling for system power management
    •Serial ROM interface supports 2-wire serial EEPROM devices
    •Two general-purpose I/Os
    •Register bits give software control of contender bit, power class bits, link 
    active control bit, and IEEE Std 1394a-2000 features 
    •Fabricated in advanced low-power CMOS process
    •PCI and CardBus register support
    •Isochronous receive dual-buffer mode
    •Out-of-order pipelining for asynchronous transmit requests
    •Register access fail interrupt when the PHY SCLK is not active
    •PCI power-management D0, D1, D2, and D3 power states
    •Initial bandwidth available and initial channels available registers
    •PME support per 1394 Open Host Controller Interface Specification
    ItemSpecification 
    						
    							24Chapter 1
    Super I/O
    Hard Disk Drive Interface
    ItemSpecification
    Type ITE- 8305E Super IO chip
    LPC Bus Interface
    •Supports I/O cycle
    •Support DMA cycle
    •Serial IRQ
    Infrared Communications Controller
    •Support Fast IR
    •Support Consumer IR
    UART 16C550A Compatible
    Parallel Port
    •Supports Standard Mode -SPP
    •Support Enhanced Mode -EPP
    •Support High-Speed Mode -ECP
    GPIO
    •Each pin can be programmed independently
    •Maximum 30 pins
    Package 48 pin LQFP package
    ItemSpecifications
    Vendor & 
    Model 
    NameHitachi
    5K320-320
    5K320-250
    5K320-120Segate
    ST9250827ASTo s h i b a
    MK2546GSX
    MK1646GSXTo s h i b a
    MK3252GSXWD
    WD2500BEVSWD
    WD3200BEVT
    Capacity 
    (MB)320, 250, 120 250 250, 160 320 250 320
    Bytes per 
    sector512 512 512 512 512 512
    Data heads4, 4 or 3, 2 4 4, 3 4 4 4
    Drive Format
    Disks
    2, 2, 1 2 2, 2 2 2 2
    Spindle 
    speed 
    (RPM)5400 5400 5400 5400 5400 5400
    Performance Specifications
    Buffer size 
    8 MB 8 MB 8 MB 8 MB 8 MB  8 MB
    InterfaceSATA SATA SATA SATA SATA SATA
    Internal 
    transfer 
    rate (Mbits/
    sec, max)674 ~ 775 778 370 ~ 720 
    typical400 ~ 794 
    typical850 Mbits/s 
    maximum850 Mbits/s 
    maximum
    I/O data 
    transfer 
    rate
    (Mbytes/
    sec max)1.5 / 3.0 300 300 3000 150 maximum 300 maximum
    DC Power Requirements
    Voltage 
    tolerance
    5V ±5% 5V ±5% 5V ±5% 5V ±5% 5V ±5% 5V ±5% 
    						
    							Chapter 125
    Super-Multi Combo Module
    ItemSpecification
    Manufacturer and Model Sony DL 8X AD-7560S
    Toshiba DL 8X TS-L633A
    Type Drawer type
    Interface SATA
    Data Transfer Modes
    •PIO Mode4
    •DMA Multiword Mode2 
    •ULTRA DMA Mode2
    Buffer Memory Size 2 MB
    Maximum Write Speed
    •CD-R Max. 24X (3,600 KB/sec)
    •DVD+RW Max 8X (10,800 KB/sec)
    Maximum Read Speed
    •CD 3,600 KB/sec
    •DVD 10,800 KB/sec
    Format Compatibility CD
    •CD-DA (Red Book) - Standard Audio CD & CD-TEXT
    •CD-ROM (Yellow Book Mode1 & 2) - Standard Data
    •CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
    •CD-I (Green Book, Mode2 Form1 & 2, Ready, Bridge)
    •CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
    •Video-CD (White Book) - MPEG1 Video
    •CD-R (Orange Book Part ‡U)
    •CD-RW & HSRW (Orange Book Part IV Volume1 & Volume2)
    •Super Audio CD (SACD) Hybrid type
    •US & US+ RW
    DVD
    •DVD-ROM (Book 1.02), DVD-Dual
    •DVD-Video (Book 1.1)
    •DVD-R (Book 1.0, 3.9G)
    •DVD-R (Book 2.0, 4.7G) - General & Authoring
    •DVD+R (Version 1.0)
    •DVD+RW
    •DVD-RW (Non CPRM & CPRM)
    •DVD±R Dual
    •DVD-RAM
    Power Supply DC +5V / 1.3A
    Voltage Allowance DC +5V 
    (5% (Operating), DC +5V(8% (Start Up)) 
    						
    							26Chapter 1
    Combo Drive Module
    Keyboard
    ItemSpecification
    Manufacturer and Model Sony DL 24X CRX890S
    Toshiba DL 24X TS-L463A
    Type Drawer type
    Interface SATA
    Data Transfer Mode PIO Mode4
    Buffer Memory Size 2 MB
    Maximum Write Speed
    •CD 3,600 KB/sec
    Maximum Read Speed
    •CD 3,600 KB/sec
    •DVD 10,800 KB/sec
    Formats Supported CD
    •CD-DA (Red Book) - Standard Audio CD & CD-TEXT
    •CD-ROM (Yellow Book Mode1 & 2) - Standard Data
    •CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-
    Session
    •CD-I (Green Book, Mode2 Form1 & 2, Ready, Bridge)
    •CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
    •Video-CD (White Book) - MPEG1 Video
    •CD-R (Orange Book Part ‡U)
    •CD-RW & HSRW (Orange Book Part‡V Volume1 & 
    Vo l u m e 2 )
    •Super Audio CD (SACD) Hybrid type
    •US & US+ RW
    DVD
    •DVD-ROM (Book 1.02), DVD-Dual
    •DVD-Video (Book 1.1)
    •DVD-R (Book 1.0, 3.9G)
    •DVD-R (Book 2.0, 4.7G) - General & Authoring
    •DVD+R (Version 1.0)
    •DVD-RW, DVD+RW
    •DVD+R DL
    •DVD-R DL
    •Support CPRM (read)
    •Support VCPS (read)
    Power Supply DC +5V / 1.3A
    Voltage Allowance DC +5V 
    (5% (Operating), DC +5V(8% (Start Up))
    ItemSpecification
    Keyboard controller KB926
    Number of keys 88-/89-key keyboard
    Windows logo key Yes
    Internal & external keyboard work 
    simultaneouslyYe s 
    						
    							Chapter 127
    Battery 
    LCD 14.1” 
    ItemSpecification
    Vendor & model name Sanyo/Sony/Panasonic/Simplo Sony/Simplo
    Battery Type Li-ion Li-ion
    Pack capacity  4400 mAh 7200 mAh
    Number of battery cell 6 9
    Package configuration 3S2P 3S3P
    ItemSpecification
    Vendor/model name AUO B141EW05 V0
    AUO B141EW05 V1
    Screen Diagonal (mm) 357.7 (14.1”)
    Active Area (mm)303.36 x 189.6
    Display resolution (pixels) 1280x3 (RGB) x 800
    Pixel Pitch 0.237
    Pixel Arrangement R.G.B. Vertical Stripe
    Display Mode Normally White
    Typical White Luminance (cd/m
    2) also 
    called Brightness220 typ. (5 points average)
    187 min. (5 points average)
    Luminance Uniformity 1.25 max. (5 points)
    Contrast Ratio 400 typ
    Response Time (Optical Rise Time/Fall 
    Time) msec8 typ / 12 Max
    Nominal Input Voltage VDD +3.3 typ.
    Typical Power Consumption (watt) 4.9 max./4.2 max. (Include Logic and Blu power)
    Weight 375 max.
    Physical Size (mm) 319 - 320 max. (L) x 205 - 206 max. (W)
    Electrical Interface 1 channel LVDS
    Support Color 262K colors (RGB 6-bit)
    Viewing Angle (degree)
    Horizontal: Right/Left
    Vertical: Upper/Lower40 - 45
    10 -15/30-35
    Temperature Range (°C)
    Operating
    Storage (shipping)0 to +50
    -20 to +65 
    						
    							Chapter 229
    System Utilities
    BIOS Setup Utility
    The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
    Output System).
    Your computer is already properly configured and optimized, and you do not need to run this utility. However, if 
    you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 
    Troubleshooting when problem arises.
    To activate the BIOS Utility, press F2 during POST (when “Press  to enter Setup” message is prompted 
    on the bottom of screen).
    Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change 
    boot device without entering BIOS Setup Utility, please set the parameter to “enabled”. 
    Press  during POST to enter multi-boot menu. In this menu, user can change boot device without 
    entering BIOS SETUP Utility.
    Navigating the BIOS Utility
    There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.
    Follow these instructions:
    •To choose a menu, use the left and right arrow keys.
    •To choose an item, use the up and down arrow keys.
    •To change the value of a parameter, press F5 or F6.
    •A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
    •Press Esc while you are in any of the menu options to go to the Exit menu.
    •In any menu, you can load default settings by pressing F9. You can also press F10 to save any 
    changes made and exit the BIOS Setup Utility.
    NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a 
    particular menu are shown on the bottom of the screen. Help for parameters are found in the Item 
    Specific Help part of the screen. Read this carefully when making changes to parameter values. Please 
    note that system information is subject to different models.
    Chapter 2 
    						
    							30Chapter 2
    Information
    The Information screen displays a summary of your computer hardware information.
    NOTE: The system information is subject to different models.
    ParameterDescription
    CPU Type This field shows the CPU type and speed of the system.
    CPU Speed This field shows the speed of the CPU.
    HDD Model Name This field shows the model name of HDD installed on primary IDE master.
    HDD Serial Number This field displays the serial number of HDD installed on primary IDE master.
    ATAPI Model Name This field shows the model name of the Optical device installed in the system.
    System BIOS Version Displays system BIOS version.
    VGA BIOS Version This field displays the VGA firmware version of the system.
    Serial Number This field displays the serial number of this unit.
    Asset Tag Number This field displays the asset tag number of the system.
    Product Name This field shows product name of the system.
    Manufacturer Name This field displays the manufacturer of this system.
    UUID Number Universally Unique Identifier (UUID) is an identifier standard used in software 
    construction, standardized by the Open Software Foundation (OSF) as part of 
    the Distributed Computing Environment (DCE).
    Information     Main     Advanc ed Int el Sec urit y Boot Ex it
    CPU Ty pe: Int el (R) Core (TM)2 Duo CPU       T9400  @ 2.53GHz
    CPU Speed: 2530 MHz
    HDD Model Name: W DCW D2500BEVS-22UST-(PM)
    HDD Serial Number: W D-W XC208827525
    A TA P I Model  Name: Opt i arc DV DRW A D-75-(S M)
    System BIOS Version:      v0.15A
    VGA BIOS Version: Intel V1625
    Serial Number:
    Asset Tag Number:
    Produc t Name: TravelMat e 6493
    Manufac t urer Name: Ac er
    UUID: 2A8D1752FA11A28D8E77001EEC42C73D
    F1 Help           
    ↑↓ Select Item           F5/F6 Change Values          F9 Setup Defaults
    ESC Exit         
    ←→ Select Menu       Enter Select
    XSub-Menu    F10 Save and Exit Phoenix SecureCore(tm) Setup Utility 
    						
    All Acer manuals Comments (0)

    Related Manuals for Acer Travelmate 6493 Service Guide