Acer Travelmate 6000 Service Guide

Chapter 243
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
TNew versions of system programs
TNew features or options
TRestore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please...

44Chapter 2 

Chapter 345
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
TWrist grounding strap and conductive mat for preventing electrostatic discharge
TSmall Philips screw driver
TPhilips screw driver
TFlat head screwdriver
TPlastic flat head screw driver
THex screw driver
TTw e e z e r s
NOTE: The screws for the different components vary in size. During the disassembly...

46Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system.
3.Remove the battery pack.
NOTE:  TravelMate 6000/ TravelMate 8000 series product uses mylar or tape to fasten the FFC/FPC/
connectors/cable, you may need to tear the tape or mylar before you disconnect different FFC/FPC/
connectors., 

Chapter 347
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.
Start
Battery
HDD DoorMiddle CoverODD Module
HDD ModuleHx2
Fx2LCD ModuleSx4
ODD BoardODD Bracket
KeyboardHx2
Mx3
Main Unit...

48Chapter 3
 
Screw List
ItemDescription
A NUT-I/O 
B SCREW M1.6X4.0-I-NI-NYLOK 
C SCREW M2.0X2.5-I-NI-NYLOK 
D SCREW M2.0X3.0-I-NI-NYLOK 
E SCREW M2.0X3.5-I-NI-NYLOK 
F SCREW M2.0X5-I-NI-NYLOK 
G SCREW M2.5X3-I-NI-NYLOK
H SCREW M2.5X4.0-B-NI-NYLOK 
I SCREW M2.5X4-I-NYLOK 
J SCREW M2.5X5.0-I-NI-NYLOK 
K SCREW M2.5X5.5-P-NI-NYLOK 
LCD Module
6 LCD
Cushions
Jx6
LCD Bezel
LCD Inverter
LCD
AssemblyHx4LCD Panel
LCD Brackets Hx4LCD Coaxial
CableLCDWireless
AntennaHx2LCD Latch Kit
Bracket
Dx1
LCD Latch Kit
Dx4 

Chapter 349
L SCREW M2.5X0.45+7I-NYLOK 
M SCREW M1.7X3.5-I-BZN
N SCREW M2X3-I-BNI-NYLOK 
O SCREW M2.0X5.0-I-BNI-NYLOK 
P SCREW M2.0X6.0-I-NI-NYLOK
Q SCREW M2.5X2-I-NI-NYLOK 
R SCREW M2.5X4-I-BNI 
S SCREW M2.5X7
T SCREW M3.0X3.5
U SCREW M2.5X5 (BLACK)
ItemDescription 

50Chapter 3
Removing the Battery Pack
1.Release the battery lock.
2.Slide the battery latch then remove the battery.
 
  

Chapter 351
Removing the Optical Module/HDD Module/Wireless Lan Card and LCD 
module
Removing the Optical Module
1.Slide the optical disk drive latch.
2.Remove the ODD module.
Removing the HDD Module
1.Remove the two screws holding the HDD cover.
2.Remove the HDD cover.
3.Remove the HDD module.
Removing the Wireless LAN Card
1.Remove the screw that secures the PCI door then remove the PCI door.
2.Disconnect the right and the left wireless antenna.
3.Pop out the wireless LAN card then remove it. 

52Chapter 3
Removing the LCD Module
1.Remove the four screws that secures the middle cover; two one each side.
2.Detach middle cover with the assistance of a plastic flat head screw driver.
3.Disconnect the LCD cable then take out the cable from the upper case.
4.Disconnect the left wireless LAN antenna line. Then take out the antenna from the upper case with a 
tweezers.
5.Unscrew the four screws holding the LCD hinges; two on each side.
6.Then remove the entire LCD module.