Acer TravelMate 5720 5320 Extensa 5620 5220 User Manual

							Chapter 371
3.Disconnect the heatsink fan connector from FAN1 on the main board. 
4.Remove the two screws (C) securing the heatsink fan module.   
5.Remove the heatsink fan module from the main board. 
Removing the CPU and VGA Heatsink Module
1.See “Removing the Battery Pack” on page 60.
2.See “Removing the Lower Cover” on page 62.
StepSize (Quantity)ColorTo r q u e
1~2 M2 x L4 (2) Silver 1.6 kgf-cm
SG_Columbia.book  Page 71  Thursday, April 19, 2007  10:49 AM 
						

							72Chapter 3
3.Remove the nine screws (C) securing the CPU and VGA heatsink module in place. 
NOTE: There are only five (5) screws for the UMA module. 
4.Slide out and remove the heatsink module. 
StepSize (Quantity)ColorTo r q u e
1~9 M2 x L4 (9) Silver 3.0 kgf-cm
SG_Columbia.book  Page 72  Thursday, April 19, 2007  10:49 AM 
						

							Chapter 373
Removing the CPU 
1.See “Removing the Battery Pack” on page 60..
2.See “Removing the Lower Cover” on page 62..
3.See “Removing the Heatsink Fan Module” on page 70.
4.See “Removing the CPU and VGA Heatsink Module” on page 71.
5.Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU, then remove 
the CPU. 
NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown. 
Removing the VGA board (for Discrete model only)
1.See “Removing the Battery Pack” on page 60.
2.See “Removing the Lower Cover” on page 62.
3.See “Removing the Heatsink Fan Module” on page 70.
4.See “Removing the CPU and VGA Heatsink Module” on page 71.
SG_Columbia.book  Page 73  Thursday, April 19, 2007  10:49 AM 
						

							74Chapter 3
5.Remove the two screws (D) securing the VGA board.  
6.Carefully remove the VGA board from the main board. 
Removing the Middle Cover and the Power Board
1.See “Removing the Battery Pack” on page 60.
2.Open the LCD screen all the way to facilitate the easy removal of the middle cover. 
3.To remove the Middle Cover, carefully insert the plastic flat screwdriver under the side of the middle cover 
and gently pry up the middle cover. Continue prying on the other side until you could detach the Middle 
Cover.  
StepSize (Quantity)ColorTo r q u e
1~2 M2.5 x L5 (2) Silver 1.6 kgf-cm
SG_Columbia.book  Page 74  Thursday, April 19, 2007  10:49 AM 
						

							Chapter 375
4.Detach the cover and turn it over on the keyboard. 
5.Disconnect the Power board cable from the main board and disconnect the Power board cable. 
SG_Columbia.book  Page 75  Thursday, April 19, 2007  10:49 AM 
						

							76Chapter 3
6.Remove the Middle Cover together with the Power board. 
7.Remove the one screw (F) securing the Power board to the middle cover, and remove the Power board 
from the middle cover.   
Removing the Keyboard
1.See “Removing the Battery Pack” on page 60..
2.See “Removing the Middle Cover and the Power Board” on page 74.
StepSize (Quantity)ColorTo r q u e
1 M2 x L3 (1) Silver 1.6 kgf-cm
SG_Columbia.book  Page 76  Thursday, April 19, 2007  10:49 AM 
						

							Chapter 377
3.Remove the two screws (F) securing the keyboard to the upper case.  
4.Carefully pry the keyboard out of the latch and slide it out; then turn it over on the touchpad area. 
StepSize (Quantity)ColorTo r q u e
1~2 M2 x L3 (2) Silver 1.6 kgf-cm
SG_Columbia.book  Page 77  Thursday, April 19, 2007  10:49 AM 
						

							78Chapter 3
5.Disconnect the keyboard cable from the main board to remove the keyboard.   
Removing the LCD Module
1.See “Removing the Battery Pack” on page 60.
2.See “Removing the Lower Cover” on page 62.
3.See “Removing the WLAN Board Modules” on page 64.
4.See “Removing the Middle Cover and the Power Board” on page 74.
5.See “Removing the Keyboard” on page 76.
SG_Columbia.book  Page 78  Thursday, April 19, 2007  10:49 AM 
						

							Chapter 379
6.Remove the acetic tape and disconnect the LCD coaxial cable from the LCD1 connector on the main 
board and release it from the latch.   
7.Remove the internal microphone cable from the INTMIC1 connector on the main board. 
SG_Columbia.book  Page 79  Thursday, April 19, 2007  10:49 AM 
						

							80Chapter 3
8.Release the wireless LAN antenna cables from the hole and latches as shown. 
9.Remove the two screws (A) from the base of the unit. 
10.Remove the two screws (H) from the left and right hinge of the LCD module. 
11 .Carefully remove the LCD module from the base unit. 
NOTE: When connecting the cable back to the unit, please note that the cable should be routed well.
StepSize (Quantity)ColorTo r q u e
1~2 M2.5 x L6 (2) Black 4.0 kgf-cm
StepSize (Quantity)ColorTo r q u e
1~2 M2.5 x L8 (2) Black 4.0 kgf-cm
SG_Columbia.book  Page 80  Thursday, April 19, 2007  10:49 AM