Acer Travelmate 4600 Service Guide

54Chapter 2
Set Supervisor/User Password
If password on boot is required, the password must be set otherwise it cannot be enabled.
The formats of the password are as follows:
Length           No more than 8 characters
Characters    0-9,A-Z (not case sensitive) 
While these fields are highlighted and press “Enter”,  a window similar to the following is shown: 
If there is an old password then setup will prompt with the following window instead and a current password 
will be required to be entered at...

Chapter 255
User can now type password in field “Enter New Password”, and re-enter password in field “Confirm New 
Password” for verification. 
If the verification is OK: 
The password setting is complete after user presses enter. 
If the current password entered does not match the actual current password: 
If the new password and confirm new password strings do not match: 
Setup Notice 
Changes have been saved. 
[ continue] 
Setup Warning 
Invalid password 
Re-enter Password 
[ continue] 
Setup Warning...

56Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable 
devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM 
in module bay and onboard LAN device.
.
ParameterDescription
+Hard Drive + and - indicate device categories. Use  to expand/
collapse.
Boot order is top-down using only the top device in each 
category.
Use  and  to move highlighted item up and down. Floppy Devices
CD-ROM/DVD Drive
Netword...

Chapter 257
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS
Exit Discarding 
ChangesExit utility without saving Setup data to CMOS
Load Setup Default Load default values for all SETUP items
Discard Changes Load previous values from CMOS for all SETUP items
Save Changes  Save Setup Data to CMOS...

Chapter 358
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
!Wrist grounding strap and conductive mat for preventing electrostatic discharge
!Small Philips screw driver
!Philips screwdriver
!Plastic flat head screw driver
!Tw e e z e r s
NOTE: The screws for the different components vary in size. During the disassembly process, group the 
screws with the corresponding...

59Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system.
3.Remove the battery pack.
NOTE:  The screws used to secure bottom case and upper case are more than one type. Please group same 
type of screw together as you disassemble the system for service purpose. The image below is for your 
reference....

Chapter 360
M2.5*6 Remove the IO bezel then 
you will see.2
M2.5*6 Remove the heatsink cover 
then you will see.1
M2.5*6 Remove the HDD cover then 
you will see.1
M2.5*3 Detach the HDD module  
then you will see.1
M2.5*3 Remove the battery then you 
will see.1
Screw TypeLocationQuantity 

61Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.
Start
Battery
HDD CoverODD ModuleRAM/Wireless
CoverE*2
K*2
HDD ModuleWireless LAN
CardMemory
IO Bezel*2
*2
Heatsink
Cover
*2...

Chapter 362
 
Screw List
ItemDescription
SCREW M2.0X3.0-I-NI-
NYLOK 86.A03V7.012
SCREW I2.5*3M-
BNIH(M2.5L3)86.T25V7.012
SCREW M2.5*4L-BZN-
NYLOK 86.A03V7.006
SCREW M2.0X5-I-NI-
NYLOK 
86.T23V7.006
SCREW MM25060IL69
86.A08V7.004
SCREW M2.0*5-
I(NI)(NYLOK)
86.T23V7.010
SCREW M2.0X2.5-I-NI-
NYLOK 
86.A03V7.007
SCREW I2*3M-NIHY 
(M2L3) 
86.T25V7.008
SCREW M1.7*3.0-I 
(BK)
86.T50V7.001
SCREW I3*3.5M-
NIH(M3L3.5)86.A03V7.011
4 screw pads
M*4
LCD Bezel
*6 hinges
*2 brackets
LCD Inverter
LCD
AssemblyLCD Cover...

63Chapter 3
Removing the Battery Pack
NOTE: This chapter is base on Aspire 1410 and Aspire 1680 to edit. Since they have the similar disassemble 
and reassemble procedures.
1.Unlock the battery lock.
2.Slide the battery latch as shown then remove the battery pack.