Acer Travelmate 4210 Service Guide

							44Chapter 1
AC Adapter
ItemSpecification
Vendor & model name ROHS DELTA -90W ADP-90SB BBAHF BLACK 1.7X5.5X12.5
LITEON -90W PA-1900-04 QB BLUE 1.7X5.5X11 LF
LSE-90W SLS0202C19A157 LF BLUE 1.7X5.5X11 LF
Input Requirements
Maximum input current (A, 
@100Vac, full load)1.5A @100Vac input and maximum load
Nominal(Rated) frequency 
(Hz)50 or 60 and single phase
Frequency variation range 
(Hz)47 - 63
Nominal voltages (Vrms) 90 - 265
Efficiency  High efficiency 85% minimum, at 100~240Vac AC input, full load, 
warm-up condition.
Output Ratings (CV mode)
Rated output voltage  Offers rated output voltage 19.0V 
Voltage Range 18.2V to 19.8V
Noise + Ripple  300mvp-pmax (20MHz bandwidth) for resistor load
Rated Power 90Watts continuously at all specified conditions
Output current  0 A (min.)    to   4.74A (max.)
Dynamic Output Characteristics
Start-up time 2 sec. (@115 Vac and 230Vac full load)
Hold up time at least 10ms (@115 Vac input, full load)
Over Voltage Protection 
(OVP)30V
Over Current 
Protection(OCP)Output current limit is 6A(Max mode)
Short circuit protection Output can be shorted without damage, and auto recovery
Electrostatic discharge 
(ESD)15kV (at air discharge)
8kV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary 3000 Vac for 1 second
Leakage current  less than 250uA at 240Vac, 50Hz
Regulatory Requirements 1. CISPR 22 Class B
2. VCCI Class B
Hard Disk Drive Interface
ItemSpecification
Vendor & 
Model NameSegate 
SATAST98823AS/
HGST 
SATA 1.5G NCQ 
MORAGA+HTS5410
80G9SA00Segate SATA 
ST9100824AS LF/
Toshiba 
MK1032GSX/
HGST 
NCQMORAGA+HTS
541010G9SA00Segate SATA 
ST9120821AS LF/
Toshiba SATAI1.5G 
W/NCQ MK1234GSX 
						

							Chapter 145
Capacity (MB) 80000 100000 120000
Bytes per 
sector1024/512 512 512
Data heads 3/4 4 4
Drive Format
Disks222
Spindle speed 
(RPM)5400 RPM 5400 RPM 5400 RPM
Performance Specifications
Buffer size  8192KB 8192KB 8192KB
Interface Serial ATA Serial ATA
APA7&SATA1.0&SAT
AII(for Toshiba)Serial ATA
Max. media 
transfer rate 
(disk-buffer, 
Mbytes/s)57.6/61.6 57.6/57.6/61.6 57.6
Data transfer 
rate 
(host~buffer, 
Mbytes/s)150 MB/Sec.
SATA 1.0150 MB/Sec. 150 MB/Sec.
DC Power Requirements
Voltage 
tolerance5V(DC) +/- 5% 5V(DC) +/- 5% 5V(DC) +/- 5%
DVD-Dual Interface
ItemSpecification
Vendor & model name PHILIPS SDVD8441 PIONEER DVR-K16RA
Performance Specification
Transfer rate (KB/sec) Sustained:
Max 10.9Mbytes/secSustained:
Max 10.8Mbytes/sec
Access Time(DVD) Random Access: 130 ms
Full Stroke: 240 msRandom Access: 150 ms
Full Stroke: 300 ms
Buffer Memory 2MB 2MB
Interface Compliant to ATA/ATAPI-5 ATAPI interface
Hard Disk Drive Interface
ItemSpecification 
						

							46Chapter 1
Applicable disc format DVD(Read): DVD-ROM, DVD-Video, 
DVD-Audio, DVD-R, DVD-R 3.95GB, 
DVD-R Multi-Border, DVD-RW, 
DVD+R, DVD+R DL, DVD+R Multi-
Session, DVD+RW
CD(Read): CD-DA, CD-ROM Mode-1, 
CD-ROM/XA Mode-2 Form-1 and 
Mode-2 Form-2, CD-i, CD-i Bridge, 
Video-CD(MPEG-1), Karaoke CD, 
Photo-CD, Enhanced CD, CD Plus, 
CD Extra, itrax CD, CD-Text, CD-R, 
and CD-RW
DVD(Write): DVD Data&Video
CD(Write): CD-DA, CD-ROM Mode-1, 
CD-ROM/XA Mode-2 Form-1 and 
Mode-2 Form-2, CD-i, Video-CD, CD-
Te x tDVD(Read): DVD-5/9/10/18, DVD-R 
3.95G/4.7G, DVD-R DL, DVD-RW, 
DVD+R, DVD+R DL, DVD+RW, 
DVD+RW high speed, DVD-RAM v2.0/
2.1
CD(Read):  CD-DA, CD-ROM Mode-1, 
CD-ROM/XA Mode-2 Form-1 and 
Mode-2 Form-2, Photo CD, Video CD, 
CD-DA, CD-Extra, Mixed-CD, CD-
Text, CD-R, CD-RW, HS CD-RW, US 
CD-RW, US+ CD-RW
DVD(Write): DVD-R, DVD-RW, 
DVD+RW
CD(Write): CD-DA, CD-i, Video-CD, 
CD-Text, Photo CD, CD-Extra, Mixed-
CD, CD-R, CD-RW, HS CD-RW, US 
CD-RW, US+ CD-RW
Loading mechanism Load: Manual Drawer loading mechanism
Power Requirement
Input Voltage 5 V +/- 5 % (Operating)  5 V +/- 5 % (Operating) 
Combo Drive Interface
ItemSpecification
Vendor & model name QSIPHILIPS SCB5265 PANASONIC UJDA-770 HLDS GCC-4244N
Performance Specification
Transfer rate (KB/sec)(DVD) Sustained:
Max 11.2Mbytes/secSustained:
Max 10.8Mbytes/secSustained:
Max 11.8Mbytes/sec
Access Time DVD: Random Access: 126 ms
DVD:Full Stroke: 165 msDVD: Typical:180 ms Average: 
CD-ROM110ms
DVD-ROM 120ms
Buffer Memory 2MB 2MB 2MB
Interface Compliant to ATA/ATAPI-5 ATAPI interface ATAPI interface
Applicable disc format DVD(Read): DVD 5/9/10/18, 
DVD-ROM, DVD-Video, DVD-R 
3.95G/4.7G, DVD-RW, DVD+R, 
DVD+RW, Multi-Border DVD-R/
DVD-RW, Multi-Session 
DVD+R, DVD+RW and DVD-
RAM
CD(Read): CD-DA, CD-ROM 
Mode-1, CD-ROM/XA Mode-2 
Form-1 and Mode-2 Form-2, 
CD-i Ready, Video-CD(MPEG-
1), Karaoke CD, Super Video 
CD, Photo-CD, Enhanced CD, 
CD Plus, CD Extra, i-trax CD, 
CD-Text, CD-R, CD-RW
CD(Write): CD-DA, CD-ROM 
Mode-1, CD-ROM/XA Mode-2 
Form-1 and Mode-2 Form-2, 
CD-i, Video-CD, CD-TextCD: CD-DA, CD-ROM, 
CD-R, CD-RW, CD-
ROM XA, 
PhotoCD(MultiSession)
DVD: DVD-ROM, DVD-
Video, DVD-
RAM(2.6GB/4.7GB), 
DVD-R, DVD-
RW(Ver1.1), DVD+R, 
DVD+RW1. Reads and writes data 
in each CD-ROM, CD-
ROMXA, CD-I FMV, 
Video CD, and CD-
EXTRA
2. Reads data in Photo 
CD( Single and Multi 
session)
3. Reads and writes 
standard CD-DA
4. Reads and writes CD-
R 
5. Reads and writes CD-
RW 
6. Reads data in DVD-
ROM
Loading mechanism Load: Manual Load: Manual Load: Manual
Power Requirement
Input Voltage 5 V +/- 5 % (Operating)  5 V +/- 5 % (Operating)  5 V +/- 5 % (Operating) 
DVD-Dual Interface
ItemSpecification 
						

							Chapter 147
Power Management 
ACPI ModePower Management
Mech. Off (G3) All devices in the system are turned off completely.
Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned 
off completely.
Working (G0/S0) Individual devices such as the CPU and hard disk may be 
power managed in this state.
Sleeping State (S3) CPU Power Down
VGA Power Down
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
Super I/O Power Down
Sleeping State (S4) Also called Hibernate state. System saves all system 
states and data onto the disk prior to power off the whole 
system.
Dimensions and Weight
ItemDetails
ModelAspire 1690Aspire 3510
Deminsions 364(W) x 274.75(D) with max. 28mm(H)
Weight 
						

							Chapter 248
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, 
if you encounter configuration problems, you may need to run Setup.  Please also refer to Chapter 4
 Troubleshooting when problem arises.
To activate the BIOS Utility, press 
m during POST (when “Press  to enter Setup” message is prompted
 on the bottom of screen). 
The setup screen displays BIOS as follows:Navigating the BIOS Utility
During setup,all Fn function keys and power saving functions are disabled.
There are five menu options: Main, Advanced, Security, Boot and Exit.
Follow these instructions:
TTo choose a menu, use the cursor left/right keys (zx).
TTo choose a parameter, use the cursor up/down keys ( wy).
TTo change the value of a parameter, press p or q.
TPress ^ while you are in any of the menu options to go to the Exit menu.
TIn any menu, you can load default settings by pressing t. You can also press u to save any
                    changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a 
 particular menu are shown on the bottom of the screen. Help for parameters are found in the Item 
Specific Help part of the screen. Read this carefully when making changes to parameter values.   
FunctionItem
Information Display the system informations
Main Allows the user to specify standard IBM PC AT 
system parameters
Advanced Provides advanced settings of the system
Security Provides security settings of the system
Boot Allows the user to specify the boot options
Exit Allows the user to save CMOS setting and exit Setup
System Utilities
Chapter  2 
						

							49Chapter 2
Information 
ParameterDescription
CPU Type This item will show the CPU information of the system.
CPU Speed This item will show the CPU clock speed.
HDD Model Name This item will show the Model name of HDD installed on Primary IDE 
master. The hard disk model name is automatically detected by the 
system. If there is no hard disk present or unknown type, “None” 
should be shown on this field
HDD Serial Number This item will show the Serial number of HDD installed on Primary IDE 
master. If no Hard disk or other devices are installed on Primary IDE 
master, then it will display a blank line
ATAPI Model Name This item will show the model name of DVD/CD-ROM drive installed on 
system. The DVD/CD-ROM model name is automatically detected by 
the system. If there is no DVD/CD-ROM model present or unknown 
type, “None” should be shown on this field
System BIOS Version This field reports the BIOS version of system
VGA BIOS Version This field reports the VGA version of the system
KBC Version This field reports the keyboard controller version of the system
Serial Number This item will show the Serial number of system.
Asset Tag Number This item will show the Asset Tag number of the system.
PhoenixBIOS Setup Utility 
 .  Info.      Main       Advanced       Security       Boot       Exit 
  
CPU Type:
:  Intel(R) Pentium(R) M processor 1.86GHz    
CPU Speed
:
System BIOS Version:
 3A02
 
VGA BIOS Version:
 ATi 009.010.002.023
KBC Version:
  
Serial Number:           LXT123456705270008EF00
 
Asset Tag Number:
  
Product Name:
 Aspire 5510
 
Manufacturer Name:
 Acer
 
UUID:
 003B4852C5630010A0EA00C09FAE9B34
 
 
  
  
 
 
F1  Help        ↑↓ Select Item         F5/F6 Change Values             F9 Setup Defaults 
Esc Exit         ← →  Select Menu        Enter  Select   4Sub-Menu      F10 Save and Exit
 
HDD Model Name:
  
HDD Serial Number:
 ST9100822A
 
  1866 MHz
HATAPI Device:   
1A11                           3LG0Y4FE
Slimtype DVDRW S0SW-833S 
						

							Chapter 250
Product Name This field will show product name.
Manufacturer Name This field will show manufacturer name.
UUID This will be visible only when there is an internal LAN device present. 
ParameterDescription 
						

							51Chapter 2
Main
This menu provides you the information of the system.
ParameterDescription
System Time / System 
Date The hours are displayed with 24 hours format. The values set in these two fields 
take effect immediately.
System Memory This field reports the memory size of system base memory.  The size is fixed to 
640KB. 
Extended Memory This field reports the memory size of the extended memory in the system. 
Extended Memory size = Total memory size - 1 MB 
Video Memory VGA Memory size = 128MB     
Quiet Boot Customer Logo display will be shown during POST when it is selected.
Power on displayAuto:  During power on process, the system will detect if any display 
device is connected on external video port.  If any external display device is 
connected, the power on display will be in CRT (or projector) only mode. 
Otherwise it will be in LCD only mode. 
Both:  Simultaneously enable both the integrated LCD screen and the system’s 
external video port (for an external CRT or projector). 
Network boot When this is selected, Boot from LAN feature is enabled. When this is not 
selected, Boot from LAN feature is then disabled.
PhoenixBIOS Setup Utility 
           Info.      
Main      Advanced       Security       Boot       Exit 
 
  
Item Specific Help 
System Time: [11:59:38]  
System Date: [07/27/2005]  
  
System Memory:  640 KB 
Extended Memory:  254 KB  
Video Memory  128 MB 
  
Quiet Boot: [Enabled]  
Power on Display: [Auto ]  
  Network boot
  [Enabled]
 
F12 Boot Menu:
  [Disabled]
 
[Enabled]
  
, , or 
 selects field. 
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub -Menu      F10 Save and Exit  
D2D Recovery:              
        
						

							Chapter 252
F12 Boot Menu When this is selected, users can modify device boot priority by pressing F12 key 
during POST. When this is not selected, device boot priority will not be 
adjustable during POST.
D2D Recovery Allow user to enable/disable the Disk-to-Disk recovery
ParameterDescription 
						

							53Chapter 2
Advanced
The Advanced screen contains parameters involving your hardware devices. It also provides advanced
 settings of the system.
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
 parameter settings.
DescriptionOption
Infrared Port  Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled 
by OSDisabled
Enabled
Auto
PhoenixBIOS Setup Utility 
          Info.        Main        Advanced      Security       Boot       Exit 
 
  
Item Specific Help 
  
 
  
  
Infrared Port::
 
  
 
 
 
 
  Configure serial port B
using oprions:
[Disabled]
    No configuration
[Enabled]
    User configuration 
 
 
 [Auto]
        BIOS or OS chooses
        configuration  
 
 
   (OS Controlled)
     Displayed when
     controlled by OS 
    
 
 
    
   
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub-Menu      F10 Save and Exit  
 
  
  [Auto]