Acer TravelMate 420 User Manual

							Chapter 363
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing.  For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.   
Start
Battery
RAM DoorHDD ModuleHinge CapsODD module
MemoryAx2
Bx2ODD
HolderODD
Assembly
Fx4
Ex2
ODD DoorODD PCB
BoardODD
Drive
HDD
CoverHDD
Assembly
Hx4
HDD
CarrierHDD
ConnectorHDD
KeyboardDx4
Middle Cover
Main Unit
(See Next
Page)LCD Module
Bx1
Dx9
Cx5
Fx1
LCD BezelVGA
Shielding
Bx4
VGA
Board
Jx1
Inverter
WireInverter
BoardLCD
Panel
Bx4
Jx8
LCD
bracketsLCDLCD
Coaxial
Cable
Ax2 
						

							64Chapter 3
  
Screw List
ItemDescription
A SCREW M2.5X0.45+4A-BNI
B SAFETY SCREW M2.5X0.45+6FP-ZK(NL)
C SCREW M2.5X0.45+10FP-ZK(NL)
D SCREW M2.5X0.45+16FP-ZK (NL)
E SCREW M2.0X4FP-ZK(H3.5-3.8XT0.6)
F SCREW M2.5X0.45P+3K-ZK(NL)
G SCREW M2.0X0.4P+2.3FP-ZK
H SCREW M3.0X0.8+3K-NL
I THERMAL SCREW (Front)
J SCREW M2.0X0.4P+3FP-NI
Main Unit
Bx1
Dx9
Cx5
Lower Case
Mini PCI
Wireless CardThermal
Module
Ix2
Ox2
CPU
Main Board
AssemblyUpper Case
Assembly Ax2
Bx4
I/O Bracket
Main FrameMain Board
Ax2
MDC CableMDC Card
Fx3
Support
Bracket
Fx2
Upper Case
Shielding
Ax2
Touchpad
Button BoardCD-Player
Button
Assembly
Fx5
FFC (Touchpad
Button to
Touchpad)
TouchpadTouchpad
CoverUpper
Case
Antenna
Line
CD-Player
SupportCD-Player
ButtonFFC (CD-
Player Board
to Touchpad
Button Board)CD-Player
Board
Bx2 Jx2 
						

							Chapter 365
Removing the Battery Pack
1.Slide the battery latch as the picture shows.
2.Then remove the battery.
 
  
						

							66Chapter 3
Removing the Optical Module/HDD Module and Memory
Removing the Optical Module
1.Slide the optical drive latch.
2.Then remove the optical drive.
Removing the HDD module
1.Unscrew the two screws that secure the hard disk drive door.
2.Remove the hard disk drive module.
Removing the Memory
1.Remove the two screw that secures the RAM door.
2.Remove the RAM door.
3.Prize the retaining clips with fingers. Then remove the memory.. 
						

							Chapter 367
Removing the Keyboard/ LCD Module and VGA Board
Removing the Keyboard
1.Remove the two screws holding the hinge caps then remove the hinge caps.
2.Unscrew the four screws holding the keyboard.
3.Use a tool to press the keyboard lock latch on the right and the left side.
4.Turn over the keyboard as the picture shows.
5.Disconnect keyboard FFC then remove the keyboard.
6.Then detach the middle cover carefully.
Removing the LCD module and VGA Board
1.See “Removing the Keyboard” on page 67.
2.Remove one screw as the picture shows.
3.Remove the six screws on the rear panel and buttom panel. Three on each side.
4.Unscrew the four screws holding the VGA board assembly to the main board.
NOTE: Please make sure you have remove the screw that is near the ventilation hole as step 2 shows. 
Otherwise, you may damage the VGA board while you need to remove it. That screw secures the VGA 
board as well.
5.Disconnect the LCD inverter connector. 
						

							68Chapter 3
6.Then disconnect the VGA board connector.
7.Tilt the LCD module to 90 degree from the main unit.
8.Remove the LCD module from the main unit.
9.Detach the mylar that fastens then take the cable out of VGA shielding notch. 
10.Disconnect the LCD coaxial cable from the VGA board. 
11 .Remove the VGA shielding from the VGA board. 
						

							Chapter 369
Disassembling the Main Unit
1.See “Removing the Keyboard/ LCD Module and VGA Board” on page 67
2.Disconnect the left and the right speaker cable.
3.Disconnect the touchpad FFC.
4.Remove the 12 screws on the lower case.
5.Then detach the lower case from the main unit.
6.Disconnect the antenna line connectors that connects to the mini PCI wireless card.
7.Release the mini PCI wireless card lock with the fingers then remove it.
8.Unscrew the four screws that fasten the thremal module.
9.Remove the thermal module from the main unit. 
						

							70Chapter 3
10.Release the CPU lock.
11 .Remove the CPU from the main unit carefully.
12.Tear off the tape that fastens the antenna line to the main board. Then take the antenna line out from the 
other side.
 
13.Remove the screw here.
14.Unscrew the screw as shown here.
15.Then remove the main board assembly from the lower case.
16.Unscrew the four screw nuts that secure the I/O bracket.
17.Remove the screw on the main frame.
18.Disconnect one fan connector.
19.Disconnect another fan connector.
20.Remove the four screws that fasten the I/O bracket to the main frame.
21.Detach the I/O bracket from the main board. 
						

							Chapter 371
22.Unscrew the two screws holding the main board to the main frame.
23.Remove main board from the main frame.
24.Remove the two screws holding the MDC card.
25.Disconnect the MDC card connector and modem wire. Then remove the MDC card.
26.Insert the pins of the tweezers to the holes as red circles highlight. Press the tweezers inwards as the 
yellow arrows show. Then pull out the connector.
27.Then remove the MDC cable.
NOTE: Please see the image below for the tweezers used. You can also use any tweezers as long as it will not 
damage MDC cable connector.
                                                             Specification: AA120mm
28.Remove the three holding the support bracket.
29.Remove the support bracket.
 
  
						

							72Chapter 3
.
30.Unscrew the three screws that secure the upper case shielding.
31.Then remove the upper case shielding.
32.Disconnect the FFC then remove it.
33.Release the tape that fasten touchpad button board FFC. Then disconnect the FFC connecting to 
touchpad button board.
34.Unscrew the two screws that secure the CD player board.
35.Take the CD player board off the lower case.
36.Remove the two screws holding CD-player button and CD-player support.
37.Remove the CD-player button.
38.Press the CD-player support latch.
39.Then remove the CD-player support.