Acer Travelmate 4060 Service Guide

Chapter 352
4.Remove the three screws that secure the touchpad board.
5.Remove the touchpad board from the upper case.
6.Disconnect the touchpad board to touchpad FFC.
7.Remove the touchpad board to touchpad FFC from the uppwer case assembly.
8.Remove the four screws holding the touchpad bracket.
9.Detach the touchpad bracket from the upper case assembly.
10.Remove the touchpad from the upper case.
11 .Remove the two screws that secure the bluetooth module.
12.Disconnect the bluetooth module then remove...

53Chapter 3
2.Detach the MDC cable from the main board.
3.Remove the two screws holding the modem board then disconnect the modem board from the main 
board.
4.Disconnect the speaker cable from the main board.
5.Remove the screw that secure the main board.
6.Remove the two screw nuts as shown.
7.The you can detach the main board from the upper case. 
8.Remove the ttwo screws that fasten the N/B heatsink.
9.Remove the N/B heatsink from the main board as shown.
10.Remove the card reader dummy card from the...

Chapter 354
IMPORTANT:When assembling/disassembling the main board, whenever there is a mylar on the main board 
(see the highlighted with red below; the mylar is sami-transparent, film-like stuff ), it should be 
transferred “if necessary” to the replacement main board. Because the main board mylar should be 
stuck to the main board to prevent the antenna cable and the main board components short circuit. 
The short could cause the main board or the antenna cable burned. 

55Chapter 3
Disassembling the LCD Module
1.Remove the four screw caps as shown.
2.Remove the four screws holding the LCD bezel.
3.Then detach the LCD bezel from the LCD module.
4.Disconnect the inverter board then remove it.
5.Remove the three screws holding the right hinge.
6.Then remove the three screws that secure the left hinge.
7.Remove one screw that secure the LCD bracket.
8.Remove another screw holding the LCD bracket on the other side.
9.Then detach the LCD panel from the LCD cover carefully.
....

Chapter 356
13.Remove the left bracket as the picture shows.
14.Tear off the tape fastening the LCD cable.
15.Tear off the the LCD cable fastening the LCD cable, then remove it.. 

57Chapter 3
Disassembling the External Modules
Disassembling the HDD Module
1.Remove the two screws holding the HDD bracket on one side.
2.Remove another two screws holding the HDD bracket on the other side.
3.Then take the hard disc drive out from the HDD bracket.
Disassembling the Optical Drive Module
1.Remove the four screws as the picture shows.
2.Remove the two screws that secure the optical disc drive and the ODD holder.
3.Push the ODD holder as shown.
4.Detach the ODD holder.
5.Disconnect the ODD...

Chapter 458
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or 
modified options can give false errors and invalid system responses.
1.Obtain the failing symptoms in as much detail as possible.
2.Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating 
the same operation.
3.Use the following table with the verified symptom to determine...

59Chapter 4
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is 
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause 
damage to the drive or cause the drive to fail. 
Do the following to select the test device.
1.Boot from the diagnostics diskette and start the diagnostics program.
2.See if FDD Test is passed as the...

Chapter 460
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.Go to the diagnostic memory in the test items.
3.Press F2 in the test items.
4.Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the...

61Chapter 4
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power 
adapter cable. See the following figure
1.If the voltage is not correct, replace the power adapter.
2.If the voltage is within the range, do the following:
TReplace the System board.
TIf the problem is not corrected, see “Undetermined Problems” on page 75.
TIf the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not...