Acer TravelMate 3000 User Manual

35Chapter 2
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup 
parameters. It allows the user to specify standard IBM PC AT system parameters.
NOTE: The screen above is for reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
ParameterDescriptionFormat/Option
System Time Sets the system time. Format: HH:MM:SS 
(hour:minute:second)...

Chapter 236
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is 
because the user is not allowed to control the settings in these cases.
Quiet Boot Determines if Customer Logo will be displayed or 
not; shows Summary Screen is disabled or 
enabled. 
Enabled: Customer Logo is displayed, and 
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and 
Summary Screen is enabled. Option: Enabled or Disabled
Power on display Auto:...

37Chapter 2
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced 
settings of the system.
The table below describes the parameters in the screen. Settings in boldface are the default and suggested 
parameter settings.
ParameterDescriptionOptions
Serial port A Configure serial port A using optionsAuto/Enabled/Disabled
Infrared Port Enables, disables or auto detects the Infrared port.Auto/Enabled/Disabled
Parallel Port Enables, disables or auto...

Chapter 238
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized 
use.
PhoenixBIOS Setup Utility 
           Info.       Main       Advanced        Boot 
 
Item Specific Help Supervisor Password Is: Clear
 
User Password Is: Clear
HDD Master ID:
[Enter]Set Supervisor Password
  
Password on Boot: 
[Disabled]
 
  
 
Supervisor Password 
controls accesses of the 
setup utility.  
 
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values...

39Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the w andy keys to highlight the Set Supervisor...

Chapter 240
                After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press e....

41Chapter 2
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following 
message. 

Chapter 242
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility 
          Info.       Main       Advanced       Security        Exit 
 
  
Item Specific Help 
  
+Hard Drive
   
   
 
 + and - indicate device 
categories. Use 
to expand/collapse.
Boot order is top-down
using only the top
device in each category.
Use...

43Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS....

Chapter 244
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
TNew versions of system programs
TNew features or options
TRestore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please...