Home > Acer > Notebook > Acer Travelmate 280 Service Guide

Acer Travelmate 280 Service Guide

Here you can view all the pages of manual Acer Travelmate 280 Service Guide. The Acer manuals for Notebook are available online for free. You can easily download all the documents as PDF.

Page 71

Chapter 363
Removing the Hard Disk Drive Module
1.See “Removing the Battery” on page 62
2.To remove the hard disk drive, first remove the one screw from the hard disk drive cover, and then 
remove the cover.
3.Remove the two screws as shown and then pull the plastic tag to detach the hard disk drive module out 
from the machine carefully.
NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the hard disk drive module to the main 
unit.  It is suggested that you reverse the sequence when...

Page 72

64TravelMate 230/ 280
4.Detach the hard disk drive from the hard disk drive bracket.
NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the hard disk drive bracket to the hard 
disk drive module.  It is suggested that you reverse the sequence when you remove the screws. 

Page 73

Chapter 365
Removing the Memory Module
1.See “Removing the Battery” on page 62
2.To remove the memory module from the machine, first remove the two screws from the memory cover.
3.Lift the cover off, then remove the memory cover.
4.Push out the latches on both sides of the socket and pull the memory module out from the socket. 

Page 74

66TravelMate 230/ 280
Removing the Modem Board
1.See “Removing the Battery” on page 62
2.To remove the modem board, first remove the screw from the modem cover.
3.Remove the modem cover from the machine.
4.Remove two screws from the modem board as shown, then remove the modem board from the main unit 
carefully by using a plastic bladed screw driver.
5.Disconnect the modem cable from the modem board, then remove the modem board.
NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the...

Page 75

Chapter 367 

Page 76

68TravelMate 230/ 280
Disassembling the LCD
Removing the Middle Cover
1.See “Removing the Battery” on page 62
2.To remove the middle cover, first remove the two screws from the rear of the unit and then pry up the 
middle cover with a plastic flat screwdriver in the way as shown.
3.Disconnect the launch board cable from the launch board and then detach the middle cover away from 
the main unit.
.
Removing the Launch Board
1.See “Removing the Battery” on page 62
2.See “Removing the Middle Cover” on page...

Page 77

Chapter 369
Removing the Keyboard
1.See “Removing the Battery” on page 62
2.See “Removing the Middle Cover” on page 68
3.To remove the keyboard, first pull out and upward to expose the keyboard.
 
4.Use a plastic flat screwdriver to help disconnect the keyboard cable from the main board carefully, then 
remove the keyboard from the main board.
Removing the CD-ROM Drive Module
1.See “Removing the Battery” on page 62
2.See “Removing the Middle Cover” on page 68
3.See “Removing the Keyboard” on page 69...

Page 78

70TravelMate 230/ 280
Disassembling the CD-ROM Drive Module
1.See “Removing the Battery” on page 62
2.See “Removing the Middle Cover” on page 68
3.See “Removing the Keyboard” on page 69
4.See “Removing the CD-ROM Drive Module” on page 69
5.To disassemble the CD-ROM drive module, first remove two screws as shown.
6.Remove the CD-ROM drive bracket from the CD-ROM drive module.
NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the CD-ROM drive bracket to the CD-
ROM drive module.  It is...

Page 79

Chapter 371
NOTE: 1.Because the CD-ROM module and the heat plate share the common screw,  you only have to 
remove the two screws as shown below If you detach the heat plate from the main unit after the step of 
removing the CD-ROM.  The same principle applies to the assembly procedures.
NOTE: 2.Please follow the numeric orders such as 1, 2, 3, and 4 to screw the heat plate to the main unit.  It is 
suggested that you reverse the sequence when you remove the screws.  
Removing the LCD Module
1.See...

Page 80

72TravelMate 230/ 280
7.Remove the inverter cable from the main board with a plastic flat screwdriver.
8.Remove the LCD module from the main unit carefully.
9.Disconnect the launch board cable from the main board and remove it.
NOTE: Please arrange the inverter cable and the coaxial cable well in the way as shown after you connect 
them to the main board. 
Start reading Acer Travelmate 280 Service Guide

Related Manuals for Acer Travelmate 280 Service Guide

All Acer manuals