Acer Travelmate 2480 Service Guide

92Chapter 4
Phoenix BIOS Beep Codes
CodeBeepsPOST Routine Description
02h Verify Real Mode
03h Disable Non-Maskable Interrupt (NMI)
04h Get CPU type
06h Initialize system hardware
07h Disable shadow and execute code from the  ROM.
08h Initialize chipset with initial POST values
09h Set IN POST flag
0Ah Initialize CPU registers
0Bh Enable CPU cache
0Ch Initialize caches to initial POST values
0Eh Initialize I/O component
0Fh Initialize the local bus IDE
10h Initialize Power Management
11h Load alternate...

Chapter 493
47h Initialize I20 support
48h Check video configuration against CMOS
49h Initialize PCI bus and devices
4Ah Initialize all video adapters in system
4Bh QuietBoot start (optional)
4Ch Shadow video BIOS ROM
4Eh Display BIOS copyright notice
50h Display CPU type and speed
51h Initialize EISA board
52h Test keyboard
54h Set key click if enabled
55h Enable USB devices
58h 2-2-3-1 Test for unexpected interrupts
59h Initialize POST display service
5Ah Display prompt “Press F2 to enter SETUP”
5Bh...

94Chapter 4
8Bh Test and initialize PS/2 mouse
8Ch Initialize floppy controller
8Fh Determine number of ATA drives (optional)
90h Initialize hard-disk controllers
91h Initialize local-bus hard-disk controllers
92h Jump to UserPatch2
93h Build MPTABLE for multi-processor boards
95h Install CD ROM for boot
96h Clear huge ES segment register
97h Fixup Multi Processor table
98h 1-2 Search for option ROMs. One long, two short 
beeps on checksum failure.
99h Check for SMART drive (optional)
9Ah Shadow option...

Chapter 495
C7h Initialize notebook docking late
C8h Force check (optional)
C9h Extended checksum (optional)
CAh Redirect Int 15h to enable remote keyboard
CBh Redirect Int 13h to Memory Technologies 
Devices such as ROM, RAM, PCMCIA, and 
serial disk.
CCh Redirect Int 10h to enable remote serial video
CDh Re-map I/O and memory for PCMCIA
CEh Initialize digitizer and display message.
D2h Unknown interrupt The following are for boot block in Flash ROM
E0h Initialize the chipset
E1h Initialize the bridge...

96Chapter 4
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / ErrorAction in Sequence
LCD backlight doesnt work First, plug a monitor to CRT port. Next, enter BIOS utility to running  “Load Default Settings” then reboot the system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesnt work).
LCD cable
LCD inverter
LCD
Main board
LCD is too dark
LCD brightness cannot be adjusted Enter BIOS Utility to execute “Load Setup Default Settings”, then 
reboot system....

Chapter 497
Battery can’t be charged or discharged See “Check the Battery Pack” on page 88. 
Battery pack
Main board
System hang during POST ODD/HDD/FDD/RAM module Main board
PCMCIA-Related Symptoms
Symptom / ErrorAction in Sequence
System cannot detect the PC Card  (PCMCIA)  PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged. PCMCIA slot assembly
PC Card cannot be inserted or ejected Check if the PCMCIA slot is blocked Main board
Memory-Related Symptoms
Symptom / ErrorAction in Sequence
Memory...

98Chapter 4
The system doesnt resume from hibernation/ 
standby mode.Connect AC adapter then check if the system resumes from 
Standby/Hibernation mode. 
Check if the battery is low.
Hard disk drive
Main board
The system doesnt resume from standby mode 
after opening the lid of the portable computer. LCD cover switch
Main board
Battery fuel gauge in Windows doesn’t go higher 
than 90%.  Refresh battery (continue use battery until power off, then charge 
battery).
Battery pack
Main board
System hangs...

Chapter 499
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined 
Problems” on page 101.
Modem/LAN-Rela
ted Symptoms
Symptom / ErrorAction in Sequence
Internal modem does not wo rk correctly. Phone cable
Driver
Reconnect the Internal modem cable to the main board tightly.
Main board
Internal LAN does not work correctly Lan cable Driver
Main board 

100Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a 
hardware defect, such as: cosmic radiation, electros tatic discharge, or software errors. FRU replacement 
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected,  do not replace any FRU.
3. If any...

Chapter 4101
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, 
whether a short circuit is suspected, or  whether the system is inoperative.  
Follow these procedures to isolate the faili ng FRU (do not isolate non-defective FRU).
NOTE:  Verify that all attached devices  are supported by the computer.
NOTE:  Verify that the power supply being used at the time  of the failure is operating correctly. (See “Power 
System...