Acer Travelmate 2440 Service Guide
Here you can view all the pages of manual Acer Travelmate 2440 Service Guide. The Acer manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 91
Chapter 481 46h 2-1-2-3 Check ROM copyright notice 48h Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h Initialize EISA board 52h Test keyboard 54h Set key click if enabled 58h 2-2-3-1 Test for unexpected interrupts 59h Initialize POST display service 5Ah Display prompt “Press F2 to enter SETUP” 5Bh Disable CPU...
Page 92
82Chapter 4 8Ch Initialize floppy controller 8Fh Determine number of ATA drives (optional) 90h Initialize hard-disk controllers 91h Initialize local-bus hard-disk controllers 92h Jump to UserPatch2 93h Build MPTABLE for multi-processor boards 95h Install CD ROM for boot 96h Clear huge ES segment register 97h Fixup Multi Processor table 98h 1-2 Search for option ROMs. One long, two short beeps on checksum failure. 99h Check for SMART drive (optional) 9Ah Shadow option ROMs 9Ch Set up Power Management 9Dh...
Page 93
Chapter 483 D2h Unknown interrupt CodeBeeps E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize the system timer E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize Multi Processor EAh Initialize OEM special code EBh Initialize PIC and DMA ECh Initialize Memory type EDh Initialize Memory size EEh Shadow Boot Block EFh System memory test F0h Initialize interrupt vectors F1h Initialize Run...
Page 94
84Chapter 4 Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / ErrorAction in Sequence LCD backlight doesnt work LCD is too dark LCD brightness cannot be adjusted LCD contrast cannot be adjustedEnter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. Reconnect the LCD connectors. Keyboard (if contrast and brightness function key doesnt work). LCD inverter ID LCD cable LCD inverter LCD System board Unreadable LCD screen Missing pels in characters Abnormal screen...
Page 95
Chapter 485 Battery can’t be charged See “Check the Battery Pack” on page 75. Battery pack System board PCMCIA-Related Symptoms Symptom / ErrorAction in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly System board PCMCIA slot pin is damaged. PCMCIA slot assembly Memory-Related Symptoms Symptom / ErrorAction in Sequence Memory count (size) appears different from actual size.Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system. DIMM System board...
Page 96
86Chapter 4 NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined Problems” on page 88. Battery fuel gauge in Windows doesn’t go higher than 90%. Remove battery pack and let it cool for 2 hours. Refresh battery (continue use battery until power off, then charge battery). Battery pack System board System hangs intermittently. Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / ErrorAction in...
Page 97
Chapter 487 Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1.Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2.If no error is detected, do not replace any FRU. 3.If any...
Page 98
88Chapter 4 Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on...
Page 99
Chapter 589 Top View 1 U39 LAN controller RTL8100CL 8 KB1 Keyboard FFC connector 2 U34 PCMCIA controller ENE CB1410 9 LED1 LED FFC connector 3 U29 Clock generator ICS951413 10 TPAD1 Touch pad FFC connector 4 U17 KBC ENE3910 11 WLBTN1 Wireless LAN launch button 5 MIC1 Microphone cable connector 12 BTBTN1 Bluetooth launch button 6 LCD1 LCD cable connector 13 SPKR1 Speaker cable connector 7 CVR1 LID switch 14 BT1 Bluetooth module cable connector Jumper and Connector Locations Chapter 5
Page 100
90Chapter 5 Bottom View NOTE: This is engineering sample. The image above may not be exactly the same as the real main board you get. 1 U53 CPU socket 13 MINI1 Wireless LAN Card Slot 2 U51 North bridge ATI RC410ME 14 DM1 DIMM Slot1 3 U57 South bridge ATI SB460 15 DM2 DIMM Slot2 4 Audio Codec ALC883 16 HDD1 HDD connector 5 U49 BIOS ROM MX29LV800 17 LIN1 Line-in Jack 6 USB3 USB connector 18 MIC2 Headphones/Speakers/Line-Out Jack 7~8 USB1 USB connectors 19 LOUT1 Line-in Jack 9 CRT1 External VGA display 20...