Acer TravelMate 2410 User Manual

							Chapter 235
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.Press e.
                After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
ParameterDescriptionOption
User Password is Shows the setting of the user password.
Clear or Set
Supervisor Password is Shows the setting of the Supervisor password
Clear or Set
Set User Password Press Enter to set the user password. When 
user password is set, this password protects 
the BIOS Setup Utility from unauthorized 
access. The user can enter Setup menu only 
and does not have right to change the value of 
parameters.
Set Supervisor Password Press Enter to set the supervisor password. 
When set, this password protects the BIOS 
Setup Utility from unauthorized access. The 
user can not either enter the Setup menu nor 
change the value of parameters.
Primary HardDisk Security Enables or disables primary hard disk security 
function. 
Password on Boot Defines whether a password is required or not 
while the events defined in this group 
happened. The following sub-options are all 
requires the Supervisor password for changes 
and should be grayed out if the user password 
was used to enter setup.
Disabled or Enabled 
						

							36Chapter 2
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. 
The computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning. 
						

							Chapter 237
If the new password and confirm new password strings do not match, the screen will display the following 
message. 
						

							38Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility 
    Information       Main       Security        Exit 
 
  
Item Specific Help 
+Hard Drive  
CD-ROM/DVD Drive    
 
 Keys used to view or configure
devices: 
 to expands or
collapses devices with a + or -
  and  moves the
device up or down.
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub -Menu      F10 Save and Exit  
Network Boot
Boot
Floppy Devices 
						

							Chapter 239
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
PhoenixBIOS Setup Utility 
  Information         Main             Security             Boot
 
  
Item Specific Help 
Exit Saving Changes  
Exit Disarding Changes   
Load Setup Defaults 
 
 Exit System Setup and save 
your changes to CMOS.
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub -Menu      F10 Save and Exit  
Discard ChangesExit
Save Changes 
						

							40Chapter 2 
						

							Chapter 341
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
TWrist grounding strap and conductive mat for preventing electrostatic discharge
TSmall Philips screw driver
TPhilips screwdriver
TPlastic flat head screw driver
TTw e e z e r s
NOTE: The screws for the different components vary in size. During the disassembly process, group the 
screws with the corresponding components to avoid mismatch when putting back the components. 
When you remove the stripe cover, please be careful not to scrape the cover.
Chapter 3
Machine Disassembly and Replacement 
						

							42Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system.
3.Remove the battery pack. 
						

							Chapter 343
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.
Start
Battery
Middle CoverHDD CoverDIMM CoverH*2
P*1
HDD ModuleO*4 H*3
CPU
Lower Case
Assembly
86.9A353.3R0*2
Modem Board
Memory
ODD Module
Wireless LAN
Card
HDDHDD BracketM*4
Keyboard
LCD ModuleJ*2 on bottom side
K*2 on top side
E*1 on upper case assemby
E*12 on bottom side
F*3 on bottom side
A*2 on rear side
Upper Case
Assembly
N*3
Upper CaseTouchpad
Assembly
Touchpad
BracketTouchpad
Lower CaseMain Board
Assembly
Speaker Set
CPU HeatsinkC*1
D*2
RTC Battery
Bluetooth
Module
ODD Module
G*2
ODDODD Bracket E*1
Microphone
North Bridge
Plate86.9A353.3R0*2 *2
O*2 O*2Fan 
						

							44Chapter 3
Screw List
ItemDescriptionPart Number
A SCW HEX NYL I#R-40/O#4-40 L5.5 34.00015.081
B SCREW MACH WAFER M2*L4 NI  86.00059.220 (PC Card slot 
x4)
C CPU SCREW M2.5*4.3L (2.3 KG) 86.00D01.230
D CPU SCREW M2.5*4.3L (1.55 KG) 86.00D02.230
E SCREW M2.5-6 86.9A323.6R0
F SCRW M2.5*L8(NON NYLOK) 86.9A323.8R0
G SCREW M2*3 NYLON 1JMCPC-420325 86.9A352.3R0
H SCREW 86.9A352.4R0
I SCREW M2.5*4L(NYLOCK)BLACK ZN  86.9A353.4R0
J SCREW M2.5X6   86.9A353.6R0
K SRW M2.5*8L B/ZN NYLOK 700  86.9A353.8R0
L SCRW M2.5*L3(NON NYLOK) 86.9A523.3R0
M SCREW M3x4(86.9A524.4R0) 86.9A524.4R0
N SCREW WAFER NYLOK NI 2ML3    86.9A552.3R0
O SCRW M2*4 WAFER NI 86.9A552.4R0
P SCRW M2.5*3 WAFER NI 86.9A553.3R0
4 screw caps
J*4 for 15
J*8 for 15.4
LCD Bezel
I*2
LCD Inverter
LCD
AssemblyLCD Panel
G*8I*2
LCD Module
LCDLCD Wire
CableLCD Brackets