Acer Travelmate 240 Service Guide

Chapter 382
7.See “Installing the CPU Heatsink Plate” on page 88.
8.See “Installing the VGA Heatsink Plate” on page 88.
9.See “Installing the Floppy Disk Drive Module” on page 88.
10.See “Installing the Touchpad Cable” on page 89.
11 .See “Installing the Touchpad Board” on page 89.
12.See “Installing the Upper Case Assembly” on page 90.
13.See “Installing the Processor” on page 91.
14.See “Installing the Thermal Module” on page 91.
15.See “Installing the MiniPCI Card Plate” on page 92.
16.See “Installing...

83TravelMate 240/ 250
Assembling the LCD Module
Installing the LCD Hinges
1.Place the left hinge to the LCD panel. Secure the left hinge with one screw.
2.Place the right hinge to the LCD panel. Fasten the right hinge with one screw.
Installing the LCD Coaxial Cable
1.See “Installing the LCD Hinges” on page 95.
2.Connect the LCD coaxial cable and fasten with mylar. Fasten the LCD coaxial cable with mylar.
 
Installing the LCD Brackets
1.See “Installing the LCD Hinges” on page 95.
2.See “Installing the...

Chapter 384
4.Attach the right bracket to the LCD. Fasten the right LCD bracket with four screws.
Installing the 15” TFT LCD
1.See “Installing the LCD Hinges” on page 95.
2.See “Installing the LCD Coaxial Cable” on page 95.
3.See “Installing the LCD Brackets” on page 95.
4.Place the LCD to the LCD panel.
5.Secure the left hinge with two screws. Fasten the right hinge with two screws.
 
Installing the Inverter Board (15” LCD)
1.See “Installing the LCD Hinges” on page 95.
2.See “Installing the LCD Coaxial...

85TravelMate 240/ 250
4.See “Installing the 15” TFT LCD” on page 96.
5.Connect the inverter cable to the inverter board. Connect the inverter board to the LCD.
NOTE: Please arrange the LCD inverter cable well to the LCD panel as the picture below shows when you 
reassemble the LCD module.
6.Secure the inverter board with one screw.
Installing the LCD Bezel
1.See “Installing the LCD Hinges” on page 95.
2.See “Installing the LCD Coaxial Cable” on page 95.
3.See “Installing the LCD Brackets” on page 95....

Chapter 386
7.Fasten the LCD bezel with the four screws. Then cover the four screw pads. 

87TravelMate 240/ 250
Installing the LCD Module
Installing the LCD Module
1.Place the LCD module to the main unit.
2.Fasten the LCD module with the two screws on the bottom; one on the right and another one on the left.
3.Secure the LCD hinge with the four screws; two on the right and two on the left.
 
4.Connect the inverter cablet to the main board. Connect the LCD coaxial cable to the maine board. Then 
fasten the LCD coaxial cable with one screw.
 
Installing the Launch Board
1.Attach the launch...

Chapter 388
Installing the Middle Cover
1.See ”Installing the Launch Board” on page 99.
2.Connect the launch board cable to the launch board.
.
3.Attach the middle cover to the main unit carefully. Then close the LCD panel and fasten the middle cover 
with your fingers on its ridge.
4.Secure the middle cover with one screw as the picture shows.
5.Then attach the left hinge cap.
6.Secure the middle cover with one screw on another side as the picture shows.
7.Then attach the right hinge cap. 

89TravelMate 240/ 250 

Chapter 390
Installing the Hard Disk Drive Module
1.Inster the hard disk drive to the main unit. Then push it to the original position carefully.
NOTE: Please attend the positive and negative of hard disk drive when insert the hard disk drive to the main 
unit. 

91TravelMate 240/ 250
Removing the Modem Board
1.Connect the modem cable to the modem board.
2.Place the modem board to the main unit carefully. Then fasten the modem board with the two screws.
3.Place the modem cover back to the machine. Then secure the modem cover with one screw.