Acer Projector Ph110 User Manual

 ... English
21
Image
(Computer Mode)
User Controls
Keystone
Adjust image distortion caused by tilting projection. ( 15 degrees)
Aspect Ratio
Use this function to choose your desired aspect ratio.
16:9 : The input source will be scaled to fit the width of the screen.
4:3 : The input source will be scaled to fit the projection screen.
Crop : A 4:3 aspect ratio picture is enlarged and the upper and
lower portions of the picture are cropped to fit the 16:9 screen.
L. Box : The input source will be scaled to...

English...
22
Image
(Video Mode)
User Controls
Keystone
Adjust image distortion caused by tilting projection. ( 15 degrees)
Aspect Ratio
Use this function to choose your desired aspect ratio.
16:9 : The input source will be scaled to fit the width of the screen.
4:3 : The input source will be scaled to fit the projection screen.
Crop : A 4:3 aspect ratio picture is enlarged and the upper and
lower portions of the picture are cropped to fit the 16:9 screen.
L. Box : The input source will be scaled to fit...

 ... English
23
Audio
(Computer / Video
Mode)
User Controls
Volume
Press the  to decrease the volume.
Press the  to increase the volume.
Mute
Choose the “On” to turn mute on.
Choose the “Off” to turn mute off. 

English...
24
Management
(Computer / Video
Mode)
User Controls
Menu Location
Choose the Menu location on the display screen.
Projection
Front-Desktop
The factory default setting.
Rear-Desktop
When you select this function, the projector reverses the image so
you can project behind a translucent screen.
Front-Ceiling
When you select this function, the projector turns the image upside
down for ceiling-mounted projection.
Rear-Ceiling
When you select this function, the projector reverses and turns the
image...

 ... English
25
Management
(Computer / Video
Mode)
User Controls
Source Lock
When source lock is turned off, the projector will search for other
signals if the current input signal is lost. When source lock is turned
on, it will “Lock” the current source channel before you press “Source”
button on remote control for next channel.
Lamp Hour Elapse
Displays Hour the lamp’s elapsed operating time (in hours).
Lamp Hour Reset
Press the  button and then choose “Yes“ to turn the lamp hour
counter to 0 hours....

English...
26
Management
(Computer / Video
Mode)
Start-up Screen
Use this function to select your desired start-up screen. If you change
the setting from one to another, when you exit the OSD menu, the
new setting will take effect immediately.
Acer: The default start-up screen of Acer projector.
User: The user customized start-up screen, which is downloaded
from PC to projector via the USB cable and My Start-up Screen
utility (refer to the description of below section).
My Start-up Screen
User Controls 

 ... English
27
AcerMy Start-up Screen is a PC utility for user to change the default
start-up screen of Acer projector to their desired image. You can install
My Start-up Screen from the bundled CD. Connect the projector to
your PC with the bundled USB cable then execute My Start-up Screen
utility to download your desired image from your PC to projector.
Before the download starts, the projector must enter “Download
Mode” first. Please follow the instruction below to enter “Download
Mode”.
1. If the AC...

English...
28
Troubleshooting
If you experience trouble with the projector, refer to the following
information. If the problem persists, please contact your local
reseller or service center.
Problem: No image appears on screen.
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp”...

 ... English
29
4. Follow the above steps 1-2. Click on the “Advanced Properties”
button.
5. Select the “Change” button under the “Monitor” tab .
6. Click on “Show all devices”. Then select “Standard monitor
types” under the “Manufacturers” box ; choose the resolution
mode you need under the “Models” box.
7. Verify that the resolution setting of the monitor display is less
than or equal to 854 x 480.
If you are using a Notebook PC:
1. You are required to implement the above steps of resolution
setting of...

English...
30Problem: The image is shrunk when displaying 4:3 DVD.
The projector automatically detects 4:3 DVD and adjusts the aspect
ratio by digitizing to full screen with 16:9 default setting.
If the image is still shrunk, you will also need to adjust the aspect
ratio by referring to the following:
Please select 16:9 aspect ratio type on your DVD player if you are
playing a 4:3 DVD.
If you can’t select 16:9 aspect ratio type on your DVD player, please
select 16:9 aspect ratio on screen menu.
Problem:...