Acer Projector Pd726w User Manual

							
9... English

Appendices

Replacing the lamp
The	projector	will	detect	the	lamp	life	itself.	It	will	show	you	a	
warning	message	“Lamp	is	approaching	the	end	of	its	useful	
life	in	full	power	operation.	Replacement	Suggested!”	When	
you	see	this	message,	changing	the	lamp	as	soon	as	possible.	
Make	sure	the	projector	has	been	cooled	down	for	at	least	30	
minutes	before	changing	the	lamp.	
Warning:	Lamp	
compartment	is	hot!		
Allow	it	to	cool	down	
before	changing	lamp!
Warning:  To	
reduce	the	risk	of	
personal	injury,	do	not	
drop	the	lamp	module	
or 	touch 	the 	lamp 	bulb.	
The	bulb	may	shatter	
and	cause	injury	if	it	is	
dropped.
	13
4	2
Lamp Changing Procedure: 
1.	 Turn	the	power	off	the	projector	by	pressing	the	Power	button.
2.	 Allow	the	projector	to	cool	down	at	least	30	minutes.
3.	 Disconnect	the	power	cord.
4.	 Remove	the	cover.

5.	 Push	up	and	remove	the	cover.	
6.	 Remove	the	3	screws	from	the	lamp	module.
7.		Pull	out	the	lamp	module.	
To replace the lamp module, reverse the previous steps. 
						

							
0English ...

Appendices

Problem: Message Reminders
	“Lamp	is	approaching	the	end	of	its	useful	life	in	full	power	opera-
tion.	Replacement	Suggested!”	will	be	shown	about	10	seconds	
when	lamp	life	is	going	to	deplete.
	“Projector 	Overheated.	 Lamp	will	automatically	turn	 off	soon.” 	will	
be	shown	when	the	system	temperature	is	over	heat.
	“Fan	fail.	Lamp	will	automatically	turn	off	soon.”	will	be	shown	
when	the	fan	is	out	of	order. 
						

							
... English

Appendices

SpecificationsSpecifications
The	specs	specified	below	are	subject	to	change	without	notice.		Regarding	the	final	specs,	
please	refer	to	Acer	accounced	marketing	specs.
Light	Valve-Single	Chip	DLPTM	Technology	by	Texas	Instruments
Lamp-260W	User	Replaceable	Lamp	for	PD724
-
300	W	User	Replaceable	Lamp	for	PD726
Number	of	Pixels
- 1024	pixels(H)	X	768	lines(V)
Displayable	Color
- 16.7M	colors
Contrast	Ratio
- 2500:1	(Full	On/Full	Off)
Uniformity-90%
Noise	Level-28dB(A)(standard	mode	/	26dB(A)(ECO	mode)	for	PD724
- 30dB(A)(standard	mode	/	28dB(A)(ECO	mode)	for	PD726
Projection	Lens
- F/2.4~2.6	f=28.0~33.6mm	with	1.2X	Manual	zoom	lens
Projection	Screen	Size	(Diag.)
- 25	to	300	inches	Diagonal
Projection	Distance
-3.94	to	39.43	feet	(1.2	to	12.02	meters)
Video	Compatibility
- NTSC	 3.58/NTSC	 4.43/PAL/SECAM	 and	HDTV	 compat-
ible		
- Composite	video	&	S-Video	capability
H.	Frequency
- 31.5kHz~100kHz	horizontal	scan
V.	Frequency
- 56Hz~85Hz	vertical	refresh
Power	Supply
- Universal	AC	input	100-240V	;	Input	Frequency	50/60Hz
I/O	Connectors
- Power:	AC	power	input	socket
-One	DVI	connector
-One	15-pin	D-sub	for	VGA,	component	and	HDTV	signal
-One	HDMI	input	for	Digital	Video	input
-RS232:	For	projector	remote	control
-VGA	Output:	One	15-pin	D-sub
-Video	Input:	
	 One	Composite	video	RCA	input
	 One	S-Video	input
	One	set	(3	RCA)	of	component	input
-USB:One	USB	connector
-Audio	Input:	One	phone	jack	for	audio	input
-Audio	 Output:	 One	phone	 jack	for	wireless	 audio	output	(for PD724W/PD726W only)
-Lan	 Output:	 One	Lan	port	 (RJ45	 connector	 for	10/100M	
Ethernet)	(for PD724W/PD726W only)
Weight- 7.6	lbs	(3.5kg)
Dimensions	(W	x	H	x	D)
-13.9	x	11.10	x	4.68	inches	 (350	x	282	x	119	mm)
Environmental- Operating	Temperature:	41~95oF	(5~	35oC)
Humidity:	80%	maximum	(Non-condensing)
- Storage	Temperature:	-4~140oF	(-20~60oC)
Humidity:	80%	maximum	(Non-condensing)
Safety	Regulation
- FCC	 Class	 B,	CE	 Class	 B,	VCCI-II,ETL,	 cETL,	ETL-GS,	
C-tick,	PSB,	PSE,	CB	Report,	CCC 
						

							
English ...

Appendices

Compatibility Modes
ModesResolutionV.Frequency [Hz]H.Frequency [KHz]
VGA - Analog
VGA640x4806031.5640x4807237.9
640x4807537.5640x4808543.3
720x4007031.5720x4008537.9
SVGA800x6005635.2800x6006037.9
800x6007248.1800x6007546.9
800x6008553.7XGA1024x7686048.4
1024x7687056.51024x7687560.0
1024x7688568.7SXGA1152x8647063.8
1152x8647567.51152x8648577.1
1280x10246063.981280x10247276.97
1280x10247579.98QuadVGA1280x9606059.7
QuadVGA1280x9607575.23SXGA+1400x10506063.98
MAC	LC	13”
640x48066.6634.98
MAC	II	13”640x48066.6835
MAC	16”
832x62474.5549.725
MAC	19”1024x7687560.24
MAC1152x87075.0668.68
MAC	G4640x4806031.35
i	Mac	DV
1024x7687560
i	Mac	DV1152x8707568.49
i	Mac	DV
1280x9607575
VGA - Analog – Extended Wide timing
WXGA 1280	x	7686048.36
1280	x	7687557.6
1280	x	768
8568.63
1360	x	7686047.72
DVI – Digital
VGA640x4806031.5
640x4807237.9
640x4807537.5
640x4808543.3
720x4007031.5
720x4008537.9 
						

							
... English

Appendices

ModesResolutionV.Frequency [Hz]H.Frequency [KHz]
DVI – Digital
SVGA(Compressed)800x6005635.2
800x6006037.9
800x6007248.1
800x6007546.9
800x6008553.7
XGA(Native)1024x76843.435.5
1024x7686048.4
1024x7687056.5
1024x7687560.0
1024x7688568.7
SXGA(Compressed)1152x8647063.8
1152x8647567.5
1152x8648577.1
1280x10246063.98
1280x10247579.98
1280x10248591.1
SXGA+(Compressed)1400x10506063.98
UXGA(Compressed)1600x12006075
HDMI – Digital
(1) PC Signal.*Support	above	DVI	digital	timing	format.
(2) Video Signal.
480i704	x	48059.94(29.97)15.73
480p 704	x	48059.9431.47
576i720	x	57650(25)15.63
576p 720	x	5765031.25
720p1280	x	7206045.00
720p1280	x	7205037.5
1080i1920	x	108060(30)33.75
YPbPr – Analog
480i 704	x	48059.94(29.97)15.73
480p 704	x	48059.9431.47
576i720	x	57650(25)15.63
576p 720	x	5765031.25
720p1280	x	7206045.00
720p1280	x	7205037.5
1080i1920	x	108060(30)33.75 
						

							
English ...

Appendices

Regulation & safety notices
This	appendix	lists	the	general	notices	of	your	Acer	Projector.	
FCC notice 
This	device	 has	been	 tested	 and	found	 to	comply	 with	the	limits	 for	a	Class	 B	
digital	 device	 pursuant	 to	Part	 15	of	the	 FCC	 rules.	 These	 limits	are	designed	
to 	provide 	reasonable 	protection 	against 	harmful 	interference 	in 	a 	residential	
installation. 	This 	device 	generates, 	uses, 	and 	can 	radiate 	radio 	frequency 	en
-
ergy 	and, 	if 	not 	installed 	and 	used 	in 	accordance 	with 	the 	instructions, 	may	
cause	harmful	interference	to	radio	communications.	
However,	 there	is	no	 guarantee	 that	interference	 will	not	occur	 in	a	particular	
installation. 	If 	this 	device 	does 	cause 	harmful 	interference 	to 	radio 	or 	televi
-
sion	 reception,	 which	can	be	determined	 by	turning	 the	device	 off	and	 on,	the	
user	 is	encouraged	 to	try	 to	correct	 the	interference	 by	one	 or	more	 of	the	 fol
-
lowing	measures:	
•	Reorient	or	relocate	the	receiving	antenna.	
•	Increase	the	separation	between	the	device	and	receiver.	
•	Connect	 the	device	 into	an	outlet	 on	a	circuit	 different	 from	that	to	
	
which	the	receiver	is	connected.	
•	Consult	the	dealer	or	an	experienced	radio/television	technician	for	
	
help.
Notice: Shielded cables 
All 	connections 	to 	other 	computing 	devices 	must 	be 	made 	using 	shielded	
cables	to	maintain	compliance	with	FCC	regulations.	
Caution 
Changes	 or	modifications	 not	expressly	 approved	 by	the	 manufacturer	 could	
void 	the 	user’s 	authority, 	which 	is 	granted 	by 	the 	Federal 	Communications	
Commission,	to	operate	this	computer.
	 
						

							
... English

Appendices

Operation conditions	
This	 device	 complies	 with	Part	15	of	the	 FCC	 Rules.	 Operation	 is	subject	 to	the	
following	two	conditions:	 1.	this	device	may	not	cause	harmful	interference,	and
2.	this 	device 	must 	accept 	any 	interference 	received, 	in 	cluding 	interfer
-
ence	that	may	cause	undesired	operation.	
Notice: Canadian users 
This	Class	B	digital	apparatus	complies	with	Canadian	ICES-003.	
Remarque à l’intention des utilisateurs canadiens 
Cet 	appareil 	numerique 	de 	la 	classe 	B 	est 	conforme 	a 	la 	norme 	NMB-003 	du	
Canada.	
Declaration of Conformity for EU countries 
Hereby,	 Acer,	declares	 that	this	Acer	 projector	 is	in	 compliance	 with	the	essen-
tial 	requirements 	and 	other 	relevant 	provisions 	of 	Directive 	1999/5/EC. 	(Please	
visit	http://	global.acer.com.)	
Compliant with Russian regulatory certification  
						

							
6English ...

Appendices

Important safety instructions 
Read	these	instructions	carefully.	Save	them	for	future	reference.	1.		 Follow	all	warnings	and	instructions	marked	on	the	product.	
2.		 Unplug	 this	product	 from	the	wall	 outlet	 before	 cleaning.	 Do	not	 use	
liquid 	cleaners 	or 	aerosol 	cleaners. 	Use 	a 	water-moistened 	cloth 	for	
cleaning.	
3.		 Do	not	use	this	product	near	water.	
4.		 Do 	not 	place 	this 	product 	on 	an 	unstable 	cart, 	stand 	or 	table. 	If 	the	
product	falls,	it	could	be	seriously	damaged.	
5.		 This	 product	 should	be	operated	 from	the	type	 of	power	 indicated	 on	
the	 marking	 label.	If	you	 are	not	 sure	 of	the	 type	 of	power	 available,	
consult	your	dealer	or	local	power	company.	
6.		 Do 	not 	allow 	anything 	to 	rest 	on 	the 	power 	cord. 	Do 	not 	locate 	this	
product	where	people	will	walk	on	the	cord.	
7.		 Never	 push	objects	 of	any	 kind	 into	this	product	 through	 cabinet	slots	
as 	they 	may 	touch 	dangerous 	voltage 	points 	or 	short-out 	parts 	that	
could 	result 	in 	a 	fire 	or 	electric 	shock. 	Never 	spill 	liquid 	of 	any 	kind	
onto	or	into	the	product.	
8.		 Do	 not	attempt	 to	service	 this	product	 yourself,	 as	opening	 or	remov
-
ing	 covers	 may	expose	 you	to	dangerous	 voltage	points	or	other	 risks.	
Refer	all	servicing	to	qualified	service	personnel.	
9.		 Unplug	 this	product	 from	the	wall	 outlet	 and	refer	 servicing	 to	quali
-
fied	service	personnel	under	the	following	conditions:	
a.	When	the	power	cord	or	plug	is	damaged	or	frayed.	
b.	If	liquid	has	been	spilled	into	the	product.
c.	If	the	product	has	been	exposed	to	rain	or	water.
d.	If	the	 product	 does	not	operate	 normally	 when	the	operating	 in
-
structions	 are	followed.	 Adjust	only	those	 controls	 that	are	cov
-
ered 	by 	the 	operating 	instructions, 	since 	improper 	adjustment	
of 	other 	controls 	may 	result 	in 	damage 	and 	will 	often 	require	
extensive 	work 	by 	a 	qualified 	technician 	to 	restore 	the 	product	
to	normal	condition.
e. 	If 	the 	product 	has 	been 	dropped 	or 	the 	case 	has 	been 	damaged. 	If	
the	product	exhibits	a	distinct	change	in	performance,	indicating	
a	needfor	service.
10.		To 	avoid 	hazard 	of 	unexpected 	electrical 	shock, 	use 	the 	AC 	adapter	
only	when	the	wall	socket	is	properly	grounded.	 
						

							
... English

Appendices

Canada  —  Low-power  license-exempt  radio 
communication devices (RSS-210)	
a.	Common 	information 	Operation 	is 	subject 	to 	the 	following	
two	conditions:	
1.	This	device	may	not	cause	interference,	and	
2. 	This 	device 	must 	accept 	any 	interference, 	including 	interfer
-
ence	that	may	cause	undesired	operation	of	the	device.
b. 	Operation 	in 	2.4 	GHz 	band 	To 	prevent 	radio 	interference 	to	
the	 licensed	 service,	this	device	 is	intended	 to	be	 operated	 in
-
doors	and	installed	outdoors	is	subject	to	licensing.