Acer Projector Pd721 User Manual

E

Lens capPower / Standby
Power Switch
 1
2
3
Powering On the Projector
1.Remove the lens cap.n
2.Ensure that the power cord and signal cable are securely
connected.
3.Turn on the main power switch on the side of the projector
and allow the projector to warm up for 1-2 minutes. o
4.Turn on the lamp by pressing “Power/Standby” button on
the control panel. p
The  startup screen will display and count down for 20
seconds and the Power/Standby indicator will light solid
amber.
The “LAMP” LED...


E

Installation
Powering Off the Projector
1.Press the “Power/Standby” button to turn off the projector
lamp.
2.After pressing the “Power/Standby” button, you will see a
message “Power off the lamp?” on the on-screen display.
Press the “Power/Standby” button again to confirm.
Otherwise the message will disappear after 5 seconds.
3.“Power/Standby” LED indicator will light solid amber for
about 30 seconds. After the “Power/Standby” indicator
starts flashing, you can turn off the main power switch...


E

The projector is equipped with an elevator foot for adjusting the
projector height.
To raise the projector:
1.Press the elevator button 
n
2.Raise the projector to the desired display angle o, then
release the button to lock the elevator foot into position.
3.Use 
p to fine-tune tilt-adjustment.
To lower the projector:
1.Press the elevator button.
2.Lower down the projector, then release the button to lock the
elevator foot into position.
3.Use 
p to fine-tune tilt-adjustment.
Adjusting the...


E

. x a M 1 . 8 2 8 . 3 7 0 . 3 2 1 2 . 2 7 1 5 . 1 2 2 1 . 6 4 2
. n i M4 . 3 25 . 1 65 . 2 0 15 . 3 4 15 . 4 8 11 . 5 0 2
) H x W ( . x a M 6 8 . 6 1 x  8 4 . 2 2 8 2 . 4 4 x  4 0 . 9 5 8 . 3 7 x  4 . 8 9 2 3 . 3 0 1 x  6 7 . 7 3 1 0 9 . 2 3 1 x  0 2 . 7 7 1 6 6 . 7 4 1 x  8 8 . 6 9 1
) H x W ( . n i M4 0 . 4 1 x  2 7 . 8 10 9 . 6 3 x  0 2 . 9 40 5 . 1 6 x  0 0 . 2 80 1 . 6 8 x  0 8 . 4 1 10 7 . 0 1 1 x  0 6 . 7 4 16 0 . 3 2 1 x  8 0 . 4 6 1
 4 7 . 3 4 8 . 9 4 . 6 1 7 9 . 2 2 3 5 . 9 2 1 8 . 2...


E

User Controls
Remote Control Panel Control
Panel Control & Remote Control
There are two ways for you to control the functions: Remote
Control and Panel Control.
Use the Remote Control
Power / Standby
Refer to the “Power On/Off the Projector” section on page
11~12.
Source
Press “Source” to choose RGB, DVI-Digital, DVI-Analog,
S-Video, Composite, Component and HDTV sources.
Re-Sync
Automatically synchronizes the projector to the input source,
when you press this button while the remote...


E

User Controls
Multi-Directional Selector
When you close the cover of remote control, this key can be used
as a mouse to control direction.
™The above function is only enabled with the connection
between computer and projector by Remote Mouse Y
Cable.
When the cover of remote control is opened, this key can be
used for the  
       operation for OSD display.
Page Up (Computer mode only)
Use this button to page up.
Page Down (Computer mode only)
Use this button to page down.
Laser
Aim the...


E

Enter
Confirm your selection of items, when you open the front cover
of remote control.
If the remote control cover is closed, the Enter button functions
like the left mouse button.
Use the Panel Control
Power / Standby
Refer to the “Power On/Off the Projector” section on page
11~12.
Source
Press “Source” to choose RGB, DVI-Digital, DVI-Analog,
S-Video, Composite, Component and HDTV sources.
Re-Sync
Automatically synchronizes the projector to the input source.
Zoom
When you press “Zoom”...


E

User Controls
How to operate
The Projector has multilingual On-Screen Display(OSD) menus that
allow you to make image adjustments and change a variety of
settings. In computer source, the OSD will be the “Computer
OSD”. In video source, the OSD will be the “ Video OSD”. The
projector will detect the source automatically.
To open the OSD menu, press the “Menu” button on the Remote
Control or Panel Control.
When OSD is displayed, press     key to select main items.
E.g.:Image-I
J  Image-IIJ...

	
E

User’s Info
Edits user preferences by OSD interface.  Press “Yes” to enter
“Users info” screen, you can edit as you wish.  Edited user Info
will display on lower left corner of the screen when projector is
powered ON.
1.> Use the 
   to select “Line1” function, and then press the
“Menu” button. You can input the character to line one.
2.> Use the 
       to select character, and then press
“Menu” to confirm your selection.
3.> Use the 
   to select “Line2” function, and then press the
“Menu”...



E

5.> Press “” to save and exit the “Users info.” menu.
6.> The startup screen will display the new wording after restart the
projector.
Note:

Each line can input 35 characters only.
Once entering “Users info.” menu can use remote control to
operate only.
Use “Del” to delete the previous character.
Use “Space” to add a space.
User Controls