Acer Projector Pd322 User Manual

							11... English
Installation
Power/Standby
Powering On the Projector
1.Remove the lens cap.
2.Ensure that the power cord and signal cable are securely
connected.  The Power LED will flash Red.
3.Turn on the lamp by pressing “Power/Standby” button on the
control panel.nAnd the Power LED will turn Blue.
4.Turn on your source (computer, notebook, video player ,etc.).  The
projector will detect your source automatically.
™If the screen displays “No Signal”,  please make sure the signal
cables are securely connected.
™If you connect multiple sources at the same time, using the
“Source”button on the remote control or control panel to
switch.
Powering On/Off the Projector
™Turn on the projector
first and then the signal
sources.
1       
						

							12English ...
Installation
Warning Indicator
™When the “LAMP” indicator lights solid red, the projector will
automatically shut itself down.  Please contact your local reseller
or service center.
™When the “TEMP” indicator lights solid red for about 20 seconds,
it indicates the projector has been overheated.  You will see a
message “Projector Overheated. Lamp will automatically turn off
soon.” on the on-screen display.  The projector will automatically
shut itself down.
Under normal conditions, the projector can be switched on again
after it has cooled down.  If the problem persists, you should
contact your local dealer or our service center.
™When the “TEMP” indicator flashs red for about 10 seconds, you
will see a message “Fan fail. Lamp will automatically turn off
soon.” on the on-screen display.  Please contact your local dealer
or our service center.
Powering Off the Projector
1.Press the “Power/Standby” button to turn off the projector lamp,
you will see a message “Please press power button again to
complete the shutdown process.  Warning: DO NOT unplug while
the projector fan is still running.” displayed on the projector’s
screen. Press the “Power/Standby” button again to confirm,
otherwise the message will disappear after 5 seconds.
2.The cooling fans continue to operate for about 15 seconds for
cooling cycle and the Power LED will keep red flashing from fast
to slow.  When the Power LED begins flashing slow, the projector
has entered standby mode.
If you wish to turn the projector back on, you must wait until the
projector has completed the cooling cycle and has entered
standby mode.  Once in standby mode, simply press “Power/
Standby” button to restart the projector.
3.Disconnect the power cord from the electrical outlet and the
projector.
4.   Do not turn on the projector immediately following a power off
procedure.   
						

							13... English
Adjusting the Projected Image
Adjusting the Projector Image Height
Elevator Foot
 1
23
Elevator Button
The projector is equipped with an elevator foot for adjust-
ing the image height.
To raise the image:
1.Press the elevator button 
n.
2.Raise the image to the desired height angle o, then release
the button to lock the elevator foot into position.
3.Use 
p to fine-tune the display angle.
To lower the image:
1.Press the elevator button.
2.Lower the image, then release the button to lock the elevator
foot into position.
3.Use 
p to fine-tune the display angle.
Installation
Tilt Adjusting Wheel     
						

							14English ...
Max.37.0(93.8cm)74.0(187.5cm)123.0(312.5cm)172.2(437.5cm)246.0(625.0cm)300.0(762.5cm)
Min. 32.10(81.5cm) 64.19(163.0cm) 106.98(271.7cm) 149.78(380.4cm) 213.97(543.5cm) 261.04(663.0cm)
Max.(WxH)29.50 x 25.60 (75.0 x 62.5cm)59.06 x 44.29
(150.0 x 112.5cm)98.43  x 73.82
(250.0 x 187.5cm)137.80 x 103.35 (350.0 x 262.5cm)196.85 x 147.64(500.0 x 375.0cm)240.16 x 180.12 (610.0 x 457.5cm)
Min.(WxH) 25.68 x 19.26
(65.2 x 48.9cm) 51.35 x 38.51
(130.4 x 97.8cm) 85.59  x 64.19
(217.4 x 163.0cm) 119.82  x 89.87
(304.3 x 228.3cm) 171.17  x 128.38
(434.8 x 326.1cm) 208.83 x 156.62
(530.4 x 397.8cm)
4.99(1.5m)9.84(3.0m)16.40(5.0m)22.97(7.0m)32.81(10.0m)40.03(12.2m)
Foctus Ring Zoom Ring
Adjusting the Projector Zoom / Focus
You may turn the zoom ring to zoom in or out.  To focus the image, rotate
the  focus ring until the image is clear. The projector will focus at di\
s-
tances from 5 to 40 feet (1.5 to 12.2 meters).
Adjusting Projection Image Size
64.1
(163.0cm)
106.98
(271.7cm)
149.78
(380.4cm)
213.97
(543.5cm)
261.04
(663.0cm)
37.0 (93.8cm)
74.0(187.5cm)
123.0(312.5cm)
172.2(437.5cm)
246.0(625.0cm)
300(762.5cm)
4.99
40.03 32.81 22.97 16.40
9.84
(1.5m)
(12.2m) (10.0m) (7.0m) (5.0m)
(3.0m)
32.1
(64.1cm)
Screen
(Diagonal)
Screen Size Distance
™This graph is for user’s reference only.
Installation       
						

							15... English
User Controls
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote
Control and Control Panel.
Using the Control Panel
Power/Standby
4Refer to the “Power On/Off the Projector” section on pages
11-12.
Source
4Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite, Video and HDTV sources.
Menu / Enter
4Press “Menu/Enter” to launch the on screen display (OSD)
menu. To exit OSD, press “Menu” again.
4Confirm your selection of items.
Four Directional Select Keys
4Use        to select items or make adjustments to
your selection.       
						

							16English ...
User Controls
Using the Remote Control
Power
4Refer to the “Power On/Off the Projector” section on pages
11-12.
Empowering  Key
4Display the “Display Mode” submenu of the onscreen display
menu to select display mode from PC, Vedio, Theatre and User
directly.
Menu
4Press “Menu” to launch the on screen display menu.  To exit
OSD, press “Menu” again.
Four Directional Select Keys
4Use         to select items or make adjustments to
your selection.
Laser Button
4Aim the remote at the viewing screen, press and hold this
button to activate the laser pointer.
Zoom
4Zoom in / out
Keystone +  / -
4Adjusts image distortion caused by tilting the projector (±16
degrees).
Page Up (Computer mode only)
4Use this button to page up.  This function is only available
when the projector is connected to a computer via an USB cable.
Page Down (Computer mode only)
4Use this button to page down. This function is only available
when the projector is connected to a computer via an USB cable.
Re-Sync
4Automatically synchronizes the projector to the input source.
Hide
4Momentarily turns off the video. Press “Hide” to hide image,
press again to restore display of the image.
Source
4Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Freeze
4Press “Freeze” to pause the screen image.     
						

							17... English
The Projector has multilingual On Screen Display menus
that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect
the source.
How to operate
1.To open the OSD menu, press “Menu” on the Remote
Control or press “Menu/Enter”on the Control Panel.
2.When OSD is displayed, use     keys to select any item in the
main menu. After selecting the desired main menu item, press 
to enter sub menu for feature setting.
3.Use    keys to select the desired item and adjust the
settings by 
    key.
4.Select the next item to be adjusted in the sub menu and adjust as
described above.
5.Press “Menu” on the Remote Control or press “Menu/Enter”on
the Control Panel, the screen will return to the main menu.
6.To exit OSD, press “Menu” on the Remote Control or press
“Menu/Enter”on the Control Panel again.  The OSD menu will
close and the projector will automatically save the new settings.
On Screen Display Menus
User Controls
Main Menu
Sub Menusettings     
						

							18English ...
Language
(Computer / Video
Mode)
Language
Choose the multilingual OSD menu . Use the   or  key to select
your prefered language.
Press “Menu” on the Remote Control or press “Menu/Enter”on
the Control Panel to finalize the selection.
User Controls     
						

							19... English
User Controls
Color
(Computer / Video
Mode)
Display Mode
There are many factory presets optimized for various types of
images.
4PC : For computer or notebook.
4Video : For playing video in a bright environment.
4Theatre : For Home Theatre usage in a dark room.
4User : Memorize user’s settings.
Brightness
Adjust the brightness of the image.
4Press the  to darken image.
4Press the  to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
4Press the  to decrease the contrast.
4Press the  to increase the contrast.
Color Temperature
Adjust the color temperature. At higher temperature, the screen
looks colder; at lower temperature, the screen looks
warmer.     
						

							20English ...
Color
(Computer / Video
Mode)
White Segment
Use the white Segment control to set the white peaking level of
DMD chip.  0 stands for minimal segment, and 10 stands for
maximum segment.  If you prefer a stronger image, adjust towards
the maximum setting.  For a smoothand more natural image, adjust
towards the minimum setting.
Degamma
Effects the represent of dark scenery.  With greater gamma value,
dark scenery will look brighter.
Saturation
Adjusts a video image from black and white to fully saturated color.
Press the  to decrease the amount of  color in the image.
Press the  to increase the amount of color  in the image.
™“Saturation” and
“Tint” functions are not
supported under
computer mode.
User Controls