Acer Projector Pd321 User Manual

11
English
Powering Off the Projector
1.Press the “Power” button to turn off the projector lamp.
2.After pressing the “Power” button, you will see a message
“Power off the lamp?” on the on-screen display. Press the
“Power” button again to confirm.
Otherwise the message will disappear after 5 seconds.
3.Power/Standby indicator flashes orange for about 40
seconds. The projector will  automatically shut itself down.
If you want to turn on the projector again, you must press the
“Power” button within 40...

12
English
Installation
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with an elevator foot for adjusting
the projector height.
To raise the projector:
1. Press the elevator button 
n.
2.Raise the projector to the desired display angle o, then
     release the button to lock the elevator foot into position.
3. Use 
p to fine-tune the display angle.
To lower the projector:
1. Press the elevator button.
2. Lower the projector, then release the button to lock the...

13
English
. x a M) m c 4 . 1 8 (  1 . 2 3) m c 6 . 3 0 2 (  2 . 0 8) m c 3 . 9 3 3 (  6 . 3 3 1) m c 2 . 7 0 4 (  3 . 0 6 1) m c 0 . 3 4 5 (  8 . 3 1 2) m c 7 . 8 7 6 (  2 . 7 6 2
. n i M)m c 0 . 0 7 (  6 . 7 2)m c 1 . 5 7 1 (  9 . 8 6)m c 8 . 1 9 2 (  9 . 4 1 1)m c 2 . 0 5 3 (  9 . 7 3 1)m c 9 . 6 6 4 (  8 . 3 8 1)m c 7 . 3 8 5 (  8 . 9 2 2
) H x W ( . x a M 6 2 . 9 1 x  8 6 . 5 2
) m c 8 . 8 4 x m c 1 . 5 6 ( 2 1 . 8 4 x  6 1 . 4 6
) m c 2 . 2 2 1 x m c 9 . 2 6 1 ( 6 1 . 0 8 x  8 8 . 6 0 1
) m c 6 . 3...

14
English
User Controls
Remote Control Panel Control
Panel Control & Remote Control
There are two ways for you to control the functions: Remote
Control and Panel Control.
Using the Panel Control
Power
4Refer to the “Power On/Off the Projector” section on pages
10-11.
Source
4Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Menu
4Press “Menu” to launch the on screen display (OSD) menu.
To exit OSD, press “Menu” again.
Keystone   
4Adjusts image distortion...

15
English
Using the Remote Control
Power
4Refer to the “Power On/Off the Projector” section on pages
10-11.
Source
4Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
PiP
4Displays the “PiP” menu of the on screen display.
Keystone   / 
4Adjust image distortion caused by tilting the projector (±16
degrees).
Hide
4Press “Hide” to hide the image, press again to resume display of
           the image.
Zoom In   / Zoom Out 
4Press “in” to magnify an image on...

16
English
The Projector has multilingual On Screen Display menus
that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect
the source.
How to operate
1.To open the OSD menu, press “Menu” on the Remote Control or
Panel Control.
2.When OSD is displayed, use     keys to select the main menu.
While making a selection on a particular page, press “Enter/ 
”
key to enter sub menu.
3.Use      keys to select the desired item and adjust the
settings by...

17
English
Language
Language
You can display the multilingual OSD menu . Use the   or 
key to select your prefered language.
Press “Menu” to finalize the selection.
Computer / Video Mode
User Controls   

18
English
Edits user preferences by OSD interface. Press “Yes” to enter “User’s
info.” screen, you can edit as you wish. Edited User’s info will
display on lower left corner of the screen when projector is  powered
ON.
             1. Use the WX to select “Line1” function, and then press the  “Menu”
    button. You can input the character to line one.
2. Use the STWX  to select character, and then press “Menu” to
    confirm your selection.
3. Use the WX to select “Line2” function, and then press the...

19
English
            
5. Press “ “ to save and exit the “User’s info.” menu.
             6. The startup screen will display the new wording after restart
                 the projector.
Note:
4Each line can input 35 characters only.
4Once entering “User’s info.” menu can use remote control  tooperate only.
4Use “Del” to delete the previous character.
4Use “Space” to add a space.
User’s Info     

20
English
User Controls
All Images
Brightness
Adjusting the brightness of the image.
4Press the  to darken image.
4Press the  to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
4Press the  to decrease the contrast.
4Press the  to increase the contrast.
Image Optimization
Image Optimization can be incrementally adjusted between 0 and
10.  Click on...