Acer Projector Pd116p User Manual

21... English
Color
(Computer / Video
Mode)
User Controls
Tint
    Adjusts the color balance of red and green.
4Press the  to increase the amount of green in the image.
4Press the  to increase the amount of red  in the image.
Color R
Adjusts the red color.
Color G
Adjusts the green color.
Color B
Adjusts the blue color.     

22English ...
User Controls
 Keystone
Adjust image distortion caused by tilting projection. (±16 degrees)\
Aspect Ratio
Use this function to choose your desired aspect ratio.
44:3 : The input source will be scaled to fit the projection screen.
416:9 : The input source will be scaled to fit the width of thescreen.
4Auto : Keep the image with original width-higth ratio and
maximize the image to fit native horizontal or vertical pixels.
H.Position (Horizontal Position)
4
Press the  to move the image left....

23... English
Image
(Computer/Video
Mode)
Tracking
“Tracking” synchronizes the signal timing of the display with the
graphic card. If you experience an unstable or flickering image,
use this function to correct it.
Sharpness
Adjusts the sharpness of the image.
4Press the  to decrease the sharpness.
4Press the  to increase the sharpness.
™“Sharpness”
functions is not
supported under DVI
and Computer mode.
User Controls       

24English ...
User Controls
Audio
(Computer / Video
Mode)
Volume
4
Press the  to decrease the volume.
4Press the  to increase the volume.
Mute
4
Choose the “On” to turn mute on.
4Choose the “Off” to turn mute off.     

25... English
ECO Mode
Choose “On” to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise.  Choose ”Off”
to return normal mode.
Menu Location
Choose the Menu location on the display screen.
Projection
4
Front-Desktop
The factory default setting.
4Rear-Desktop
When you select this function, the projector reverses the image
so you can project behind a translucent screen.
4Front-Ceiling
When you select this function, the projector turns the image
upside down for...

26English ...
Source Lock
When source lock is turned off, the projector will search for other
signals if the current input signal is lost. When source lock is turned
on, it will “Lock” the current source channel before you press
“Source” button on remote control for next channel.
Lamp Hour Elapse
Displays the lamp’s elapsed operating time (in hours).
Lamp Hour Reset
Press the  button after choosing “Yes ”to turn the lamp hour
counter to 0 hours.
Lamp Reminding
Choose this function to show or to hide...

27... English
Management
(Computer / Video
Mode)
Acer My Start-up Screen is a PC utility for user to
change the default start-up screen of Acer projector to their desired image. You can install
My Start-up Screen  from the bundled CD.
Connect the projector to your PC with the
bundled USB cable then execute  My Start-up
Screen  utility to download your desired image
from your PC to projector. Before the download
starts, the projector must enter “Download
Mode” first. Please follow the instruction below...

28English ...
Appendices
Problem: No image appears on screen.
4Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
4Ensure the pins of connectors are not crooked or broken.
4Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
4Make sure you have removed the lens cap and the projector is
switched on.
4Ensure that the “Hide” feature is not enabled.
Problem: Partial, scrolling or...

29... English
6.Click on “Show all devices”. Then select “Standard monitor
types” under the “Manufacturers” box ; choose the resolution
mode you need under the “Models” box.
7. Verify that the resolution setting of the monitor display is less
than or equal to 800 x 600.
4If you are using a Notebook PC:
1.You are required to implement the above steps of resolution
setting of the computer first.
2. Switch the Notebook PC display to the “external display only”
or “CRT only” mode.
4If you experience...

Problem: The image is outstretched when displaying 16:9
DVD.
The projector automatically detects 16:9 DVD and adjusts the aspect
ratio by digitizing to full screen with 4:3 default setting.
If the image is still outstretched, you will also need to adjust the asp\
ect
ratio by referring to the following:
4Please select 4:3 aspect ratio type on your DVD player if you are
playing a 16:9 DVD.
4If you can’t select 4:3 aspect ratio type on your DVD player, please
select 4:3 aspect ratio in the on screen menu....